Electro-Voice RE920Tx User Manual

Key Features:

-

• Wide, Smooth Frequency Response

• Cardioid Polar Pattern

• Handles High SPL Levels

• Flexible Gooseneck Allows Easy Mic
Adjustment

General Description:

The Electro-Voice® model RE920Tx is a cardioid condenser
mic, designed specially for wireless use with musical
instruments. It includes a specially designed instrument­mount clip assembly, which securely holds the mic in place,
while isolating it from mechanical vibration. The mic is
terminated in a T A4F connector wired f or use with EV & Tele x
bodypack transmitters, and includes a two-stage foam
windscreen, and a gig bag.

RE920Tx

Unidirectional Condenser

Instrument Microphone

with T A4F Connector

Technical Specifications:

:tnemelEgnitareneG

:esnopseRycneuqerF)trahcees(zHk81–08
:nrettaPraloPdioidraC)trahcees(
tiucriCnepO,ytivitisneS

:zHk1,egatloV
:leveLgnippilCLPSBd841>
:esioNtnelaviuqELPSABd13
:egnaRcimanyDBd711>
:zHk1,ecnadepmItuptuOsmho0001
:stnemeriuqeRrewoPCDV5
:noitpmusnoCtnerruCAu005<

snoisnemiD)mm5.01(”214.0)ciM(retemaiD

feilerniarts

:elbaC5.1(tf5xretemaiD)mm45.2(”001.0

gnol)m

:gniriWrotcennoCdleihS,dnuorG–1#niP

C/N–4#niP

:dehsinruFseirosseccAneercsdniWegatSowT

gaBgiG
:roloCkcalbgnitcelfernoN
:snoitidnoClatnemnorivnE:%05-0ytidimuHevitaleR

:thgieWteN)smarg45(.zo9.1

2tertcelekcab,resnednocdesaiB-fleS

mgarhpaidderettupsdlog,kcihtnorcim

lacsaP/Vm3.1

ssel)mm1.42(”849.0)ciM(htgneL

)mm851(”2.6)detnuoM(htgneL

etihW,oiduA–2#niP

deR,egatloVsaiB–3#niP

)F°561ot°02-(C°47ot°92-

:%59-0ytidimuHevitaleR

)F°531ot°02-(C°75ot°92-

)smarg45(.zo18.0:ylnociM

Frequency Response:

270°

0°

@1kHz

0

FREQUENCY IN HERTZ

K

+10

dB

Polar Response:

330°

300°

0°

30°

60°

-10

20 50

100 1K 5K 10K 20

500

240°

210°

-20dB

-15dB

-10dB

-5dB

180°

150°

9

120°

Application Notes:

Cable Clips:

The gooseneck on the RE920Tx includes a pair of soft vinyl clips to hold the microphone cable. These can be adjusted
as needed to make sure the cable does not interfere with the use of your instrument.

Using the Windscreen:

The RE920Tx includes a windscreen that can be used anytime wind noise is a problem. To install the windscreen,
simply press it on the top of the microphone. The windscreen has an internal frame that includes a stop to help
positioned the windscreen correctly . When installing the windscreen, make sure to push it down on the microphone as
far as it will go . This will ensure that the frame inside the windscreen doesn’t co ver any of the acoustic side ports on
the microphone.

Microphone Placement:

Some suggested microphone placements are described
below . The tone of the instrument can be varied a great
deal depending on the exact placement of the mic. The
optimum placement is the one where the mic sounds
best and is mostly a matter of personal preference.

Mic Removal/Insertion/Dimensions:

T rumpets and T r ombones

Mount the microphone on the bell of the instrument as
shown on the rev erse side of this sheet. P ointing the
mic towards the center of the bell will result in a
brighter sounding tone.

Saxophones

Mount the microphone on the bell of the instrument as
shown on the rev erse side of this sheet. P ointing the
mic towards the center of the bell will result in a
brighter sounding tone.

Woodwinds

For a bright sound, clamp the microphone on the bell of
the instrument and point it towards for the center of the
bell. For a mellower sound, reverse the mic clamp so
that mic points towards the instrument keys.

12000 Portland Avenue South, Burnsville, MN 55337
Phone:[phone], Fax:[phone]

www.electro voice.com

© T elex Communications, Inc. 3/2005

Part Number 38110-436 Rev A

Microphone Removal:

To remove the mic from its clip ,

gently twist it upward as shown
while grasping the plastic clip.

Microphone Insertion:

To insert the mic into its clip,
push the mic straight down as
shown until it snaps into place.
Make sure the grove in the mic
engages the internal ribs in the
clip .

U.S.A. and Canada only. For customer orders, contact Customer Service at:

800/392-3497 Fax: [phone]

Europe, Africa, and Middle East only. For customer orders, contact Customer Service at:

+ 49 9421-706 0 Fax: + 49 9421-706 265

Other International locations. For customer orders, contact Customer Service at:

+ 1 952 884-4051 Fax: + 1 952 736-4212

For warranty repair or service information, contact the Service Repair department at:

800/553-5992 or 402/467-5321

For technical assistance, contact Technical Support at: 800/392-3497 or 952/736-4656

Specifications subject to change without notice.