Page 1
Key Features:
PolarChoice Series:
PC-12/FL
PC-18/FL
Threaded/Flange Mount Miniature
Multi-Pattern Podium Microphone
• Dual Capsule Design with four polar
patterns: Omnidirectional, Cardioid,
Supercardioid, and Hypercardioid.
• Thread or flange mount
• Cable can exit from the side or through
the bottom of the gooseneck
• Switchable high pass filter
• Consistent on-axis response.
• Available in 12 or 18 inch versions.
• Non-reflecting black finish
• Phantom powered back-electret
condenser
• Packaged with a two-piece shock mount
General Description:
The PC-12/FL and PC-18/FL are multi-pattern miniature gooseneck podium microphones designed for sound
reinforcement systems where sound quality and gain-before-feedback is of major importance. The multi-pattern
versatility of the PolarChoice microphone makes it true problem solver. With three directional and one nondirectional polar pattern available, the PolarChoice microphone is ideal for virtually any installation. Polar
patterns can be easily changed, using a small flat bladed screwdriver with the front mounted rotary control on
the external electronics module. The control switch has the following settings:
Switch Setting Polar Pattern
Altering the polar pattern does not change the on-axis sonic character of the
microphone; therefore changes in equalizer settings are unnecessary. The PC12/FL and PC-18/FL are acoustically designed for high-quality sound
reinforcement and broadcast applications. The frequency response is tailored
for wide-range sound reproduction with very natural sound pick-up for either
distant or close-up use.
The PC-12/FL and PC-18/FL microphones can be mounted in several different ways. They can be mounted on
any fixture that has a standard 5/8" X 27 microphone thread (such as a microphone stand), or they can be
mounted to any flat surface using the included threaded flange. Additionally, they can be mounted using the
included shock mount and adapter. The cable can be easily changed to exit from either the side, or through the
bottom of the microphone.
The small, dual diameter gooseneck has two supple joints and a rigid center tube. The rigid tube prevents
unsightly twisting of the gooseneck but permits the user to exactly position the microphone. The electronics
module is terminated with a male XLR-type 3-pin connector that allows the microphone to be plugged directly
into an existing panel-mount XLR receptacle. The electronics module can also be surface mounted using the
included mounting clips. The housing is machined brass for ruggedness and superior EMI/RFI attenuation. The
PC-12/FL and PC-18/FL are designed to be phantom-powered with a wide voltage range of 12-52V dc (DIN
Standard 45 596).
Page 2
PolarChoice Series PC-12/FL and PC-18/FL Microphones
Applications:
The PC-12/FL and PC-18/FL can be used on lecterns, podiums, desk and tabletops, or other applications that require a
threaded or flange mounted gooseneck microphone. To maximize gain-before-feedback the PolarChoices
three directional
polar patterns allow the user to pick the directional polar pattern for optimum effect. For those applications where gainbefore-feedback is not a problem, an omnidirectional pattern is included. Applications requiring speaking close to the
microphone at podiums, lecterns, or pulpits normally require a windscreen to control breath noise and P-popping or, in
some cases, wind noise from circulating air.
Technical Specifications:
Generation Element:
Dual condenser, back electret
Frequency Response:
50 Hz to 20,000 Hz (see chart)
Polar Patterns: (see chart)
Omnidirectional
Cardioid
Supercardioid
Hypercardioid
Sensitivity,
Open Circuit Voltage, 1 kHz:
5.6mV/Pascal
Clipping Level (1% THD):
>135 dB SPL
Equivalent Noise:
<26 dB SPL A weighted
(0 dB=20 micropascals)
Dynamic Range:
>109 dB
Output Impedance, 1 kHz:
200 ohms
Power Requirements:
Phantom, 12 52 VDC
Current Consumption:
< 8 mA with P12 supply
Polarity:
Pin 2 positive, referenced to pin 3, with positive pressure on
the diaphragm
Dimensions
Gooseneck Length:
PC-12/FL: 313.2 mm (12.3 in.)
PC-18/FL: 457.7 mm (18.0 in.)
Maximum Head Diameter: 14.6 mm (0.58 in.)
Gooseneck Diameter:
Lower section, 7.9 mm (0.31 In.)
Upper section, 6.4 mm (0.25 In.)
Electronics Module Diameter: 20 mm (0.79 in.)
Connector Diameter: 19 mm (0.75 in.)
Accessories Furnished:
Windscreen
Two-piece shock mount, with shock mount adaptor
Mounting clips for electronics module
Optional Accessories:
FMK flange-mount kit
CPSM shock-mount kit
Color:
Nonreflecting black
Environmental Conditions,
Relative Humidity 0-50%:
-29° to 74°C (-20° to 165°F)
Relative Humidity 0 to 95%:
-29° to 57°C (-20° to 135°F)
Net Weight:
PC-12/FL:
111 grams (3.9 oz), 252 grams (8.9 oz) with electronics
module
PC-18/FL:
119 grams (4.2 oz), 261 grams (9.2 oz) with electronics
module
Dimension Drawings:
Page 3
Engineering Data Sheet
EV Multi-Port Windscreen:
All PolarChoice microphones come with the exclusive EV
Multi-Port Windscreen. This unique one-piece ported design
offers greatly improved resistance to P-popping noise by
creating a two-stage filter that has an air space between the
stages. This makes the multi-port windscreen as effective as
much larger traditional designs.
Mounting the Electronics Module:
The external electronics module can either be plugged directly
into any standard 3-pin XLR input, or it can be surface mounted
in a location adjacent to the microphone using the provided
mounting clips. If required, the cable between the microphone
and the electronics module can be shortened. Simply cut the
cable to the desired length, and remove sufficient insulation from
the wires to allow the conductors to be inserted into the terminal
strip in the electronics module. Connect the wires to the module
as shown in the wiring guide on this page. For best results, the
conductors should first be tinned with solder.
Shock Mount Installation:
Drill a 1-3/8 inch hole to mount the hard plastic flange into the
desk, table, or lectern top. Drill three holes to secure the
flange. The type of screws used to fasten the flange will
depend on the desktop material. To insert the flexible shock
mount:
1. First route the cable, as desired, either out the side of the
mic, or through the bottom.
2. Screw the included shock mount adaptor into the bottom
of the microphone.
3. Gently push the flexible shock mount onto the adaptor.
4. Insert the microphone and shock mount into the hard
plastic flange using a twisting action to seat the shock
mount.
Changing the Cable from Side Exit to
Bottom Exit:
1) Disconnect the cable from the electronics module
2) Unscrew the hex retainer from the bottom of the gooseneck.
3) Thread the cable through the knurled ring and hex retainer.
4) Screw the hex retainer back on the bottom of the goose
neck and tighten securely.
5) Reconnect the cable to the electronics module, according to
the wiring diagram.
Page 4
Frequency Response: Polars:
Architectural & Engineering Specs:
PolarChoice Series PC-12/FL, PC-18/FL
The microphone shall be a back-electret condenser type with a frequency response of 50 Hz to 20 kHz. The microphone shall have a nominal, balanced output
impedance of 200 ohms. The microphone shall have four selectable polar patterns: omnidirectional, cardioid, supercardioid, and hypercardioid. The microphone
shall have an output level of 5.6 mV/Pascal, and outputs shall not be appreciably affected by the following temperature and humidity extremes: -29° to 74° C (20° to 165°F) when the relative humidity is 0-50%; -29° to 57°C (-20° to 135°F) when the relative humidity is 0-95%. Dimensions shall be 350.7 mm (13.8 in.)
long (PC-12/FL), and 495.1 mm 19.5 in.) long, (PC-18/FL) with a maximum head diameter of 14.6 mm (0.58 in). The PC-12/FL microphone shall include a 313.2
mm (12.3 in.) gooseneck. The PC-18/FL microphone shall include a 457.7 mm (18.0 in.) gooseneck. The PC-12/FL and PC-18/FL goosenecks microphones will
include an external electronics module, which is terminated with a professional XLR-type 3-pin style connector. The electronics module will have a switchable high
pass filter to roll off low frequencies. The microphone shall be of metal construction. The microphone will include an external windscreen. The microphone shall
have a nonreflecting black finish. The Electro-Voice PolarChoice series PC-12/FL or PC-18/FL is specified.
Warranty (Limited)
Electro-Voice products are guaranteed against malfunction due to defects in materials or workmanship for a specified period, as noted in the individual productline statement(s) below, or in the individual product data sheet or owners manual, beginning with the date of original purchase. If such malfunction occurs during
the specified period, the product will be repaired or replaced (at our option) without charge. The product will be returned to the customer prepaid.
Exclusions and Limitations: The Limited Warranty does not apply to: (a) exterior finish or appearance; (b) certain specific items described in the individual
product-line statement(s) below, or in the individual product data sheet or owners manual; (c) malfunction resulting from use or operation of the product other
than as specified in the product data sheet or owners manual; (d) malfunction resulting from misuse or abuse of the product; or (e) malfunction occurring at any
time after repairs have been made to the product by anyone other than Electro-Voice Service or any of its authorized service representatives.
Electro-Voice Wired Microphones are guaranteed against malfunction from any cause for three (3) years from the date of original purchase. Any and all active
electronics incorporated in these microphones are guaranteed against malfunction due to defects in materials or workmanship for a period of three (3) years from the
date of original purchase. The Limited Warranty does not extend to cables, cable connectors, or switches.
Obtaining Warranty Service:
To obtain warranty service, a customer must deliver the product, prepaid, to Electro-Voice Service or any of its authorized service representatives together with
proof of purchase of the product in the form of a bill of sale or receipted invoice. For warranty repair or service information, contact the Service Repair
department at: 800/392-3497.
Incidental and Consequential Damages Excluded:
Product repair or replacement and return to the customer are the only remedies provided to the customer. Electro Voice shall not be liable for any incidental or
consequential damages including, without limitation, injury to persons or property or loss of use. Some states do not allow the exclusion or limitation of incidental
or consequential damages so the above limitation or exclusion may not apply to you.
Other Rights: This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state.
For Technical Assistance, contact Technical Support at 800/234-6831 or 616/695-6831, M-F, 8:00 a.m. to 5:00 p.m. Eastern Standard time. Specifications
subject to change without notice.
12000 Portland Avenue South, Burnsville, MN 55337
Phone: 952/884-4051, Fax: 952/884-0043
www.electrovoice.com
© Telex Communications, Inc. 3/2003
Part Number 38110-226 Rev. A
U.S.A. and Canada only. For customer orders, contact Customer Service at:
Europe, Africa, and Middle East only. For customer orders, contact Customer Service at:
Other International locations. For customer orders, contact Customer Service at:
For warranty repair or service information, contact the Service Repair department at:
For technical assistance, contact Technical Support at: 866/78AUDIO
Specifications subject to change without notice.
800/392-3497 Fax: 800/955-6831
+ 49 9421-706 0 Fax: + 49 9421-706 265
+ 1 952 884-4051 Fax: + 1 952 736-4212
800/392-3497
Loading...