Electro-Voice FM6.2 Datasheet
Electro-Voice | EVID FM6.2
EVID FM6.2
▪ 6.5 inch two-way system with polypropylene
diaphragm for reliable long-term operation
▪ Extremely compact depth fits into tight spaces
including walls and tight ceiling spaces
▪ Titanium coated tweeter gives even uniform high
frequency coverage
▪ Front baffle wattage tap adjustment allows for easy
level matching after installation
▪ Integrated low loss matching transformer allows for
either 70v/100v or 8 ohm operation
The EVID FM6.2 loudspeaker system from ElectroVoice is a complete two-way in-wall loudspeaker
package. The package consists of a bezel assembly,
grille, rear enclosure, 6.5 inch two-way loudspeaker
coupled with a 6.5 inch passive radiator and an
internal line-matching transformer. The loudspeaker
features 6.5 inch low-frequency cone and hightemperature voice-coil assembly along with a 6.5 inch
long excursion passive radiator and titanium coated
dome tweeter. The EVID FM6.2 loudspeaker utilizes a
crossover network, centered at 3,300 Hz, that provides
16-dB-per-octave tweeter protection outside of its
operating range. In addition the FM6.2 features a
comprehensive protection circuit to shield the woofer
and tweeter drivers from excessive power levels.
The FM6.2 utilizes a transformer that offers a selection
of 7.5, 15, 30, or 60 watts delivered to the
loudspeaker system using either 70-V or 100-V lines.
The wattage is selected via a convenient switch on the
front baffle. The unit can also be operated as an 8-ohm
speaker via the same front panel selector switch.
The perforated grille is finished in semi-gloss white
powder-coated enamel. The baffle and bezel is
constructed from heat resistant ABS. The rear
enclosure is constructed from zinc-plated, steel. The
rear enclosure provides an optimum internal volume,
ensuring extended low-frequency performance. It is
constructed from heavy-gauge, rugged steel. The steel
rear enclosure was optimized using FEA to virtually
eliminate panel resonance. The entire enclosure is less
than 4 inches deep providing an easy installation into
nearly any tight wall or ceiling space. A rear cover,
with provisions for a junction box fitting, provides
access to a 4-pin terminal block that allows direct
connection to the speaker and provides pass through
to additional speakers. FM6.2 loudspeakers provide
wide dispersion, high-efficiency, high-maximum
output, ease of installation, and wide-range
reproduction of music or voice.
Technical specifications
Frequency Response (-3 dB): 60 Hz - 20 kHz
Frequency Range (-10 dB):
Sensitivity: 90 dB (SPL 1W/1m)
Maximum SPL:
Coverage: 120°
Impedance:
Crossover Frequency:
Rec. Highpass Frequency:
Power Handling: 75W Cont. Prog. / 300W Peak
HF Transducer:
52 Hz - 20 kHz
115 dB
1
8 ohms nominal (transformer
bypass)
3.3 kHz
60 Hz
2
1 in (25.4 mm)
8.33"
[21
1.6mm]
3.45"
[87.6mm]
10.09"
[256.4mm]
18.32"
[465.4mm]
3.95"
[100.3mm]
50 100 1000 10000 20000
3.16
10
100
70
80
90
100
1
10
Sensitivity (dB)
Frequency (Hz)
Frequency Response, Half Space
Impedance
2 | EVID FM6.2
LF Transducer: 6.5 in (165.1 mm)
Passive Radiator: 6.5 in (165.1
mm)
Transformer Taps:
70V: 7.5, 15, 30, or 60W
100V: 15, 30, or 60W
Bypass: 8 ohms nominal
Connectors:
Enclosure Material:
4 pin phoenix style terminals
Baffle: UL 94V-O rated ABS
Backcan: Zinc plated steel
Grille: Perforated powdercoated steel with
safety tether
Mounting System:
Support Hardware:
Integrated toggle anchors
Cutout template, Paint shield
Dimensions: 465.4 mm x 256.4 mm x 100.3 mm
(18.32 in x 10.09 in x 3.95 in)
Net Weight (Each):
5.8 kg (12.7 lb)
Shipping Weight (Pair): 12.9 kg (28.4 lb)
All specifications based on Half-Space Environment as flush-mounted.
1
Measured on an IEC Baffle. Symmetric coverage
angle.
2
Continuous Program Rating: 3 dB greater than
continuous pink noise rating (IEC-shaped pink noise
with 6 dB crest factor)
Block diagram:
Dimensions:
Notice!
All specifications based on Half-Space Envi-
ronment as flush-mounted.
Architectural and engineering specifications:
The EVID FM6.2 loudspeaker system shall be
comprised of a baffle/bezel assembly, front grille, rear
enclosure, transformer, 6.5 inch passive radiator, and
6.5 inch loudspeaker. The loudspeaker shall meet the
requirements of UL 2043 and UL 1480. The
loudspeaker will feature a 6.5 inch low-frequency cone
and a high-temperature voice-coil assembly, coupled
with a 6.5 inch passive radiator. A 1 inch wide
dispersion titanium coated dome tweeter extends the
response to 20 kHz. Frequency response, uniform from
85 Hz to 18 kHz. Pressure sensitivity, 90 dB SPL at 1
meter (88dB at 4 feet) on axis with one watt of bandlimited pink noise from 500 Hz to 3 kHz (ref. 20 µPa).
Frequency response and impedance:
Minimum impedance, 8.6 ohms. The loudspeaker shall
be 465.4 mm (18.32 in) by 256.4 mm (10.09 in and
100.3 mm (3.95 in)) deep. Weight shall be 5.8 kg (12.7
lb). The in-wall loudspeakers packages shall be the
FM6.2 Electro-Voice model.
Loading...