EVOLVE 50 Portable Column System
en
Installation manual
EVOLVE 50 Portable Column System Table of contents | en 3
Table of contents
1
1.1 Important safety instructions 4
1.2 FCC information 5
1.3 Precautions 7
1.4 Certifications 7
1.5 Notices 8
2
2.1 Shipping contents 10
3
3.1 System features 12
3.2 Quick setup 13
4
5
5.1 Amplifier DSP controls 15
5.2 System status 16
5.3 DSP control menu 17
6
7
7.1 Stereo pair of EVOLVE 50 systems 24
7.2 Solo musician performance 25
8
9
9.1 Dimensions 29
9.2 Frequency response 30
Safety 4
Short information 10
Description 12
Installation 14
Amplifier DSP 15
Pairing the QuickSmart Mobile application 23
Recommended configurations 24
Troubleshooting 26
Technical data 28
Electro-Voice Installation manual 2018-11 | 04 | F.01U.341.540
4 en | Safety EVOLVE 50 Portable Column System
!
1 Safety
1.1 Important safety instructions
The lightning flash with arrowhead
symbol, within an equilateral triangle is
intended to alert the user to the
WARNING: TO REDUCE THE RISK OF
FIRE OR ELECTRIC SHOCK, DO NOT
OVEREXPOSE THIS APPLIANCE TO RAIN
OR MOISTURE
AVIS: RISQUE DE CHOC ELECTRIQUE,
NE PAS OUVRIR.
WARNING: THE MAINS PLUG OR AC
INLET IS USED AS A DISCONNECT
DEVICE. THE DISCONNECT DEVICE
SHALL REMAIN READILY OPERABLE.
WARNING: CONNECT ONLY TO MAINS
SOCKET WITH PROTECTIVE EARTHING
CONNECTION.
WARNING: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK) AS THERE ARE NO
USER-SERVICABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED
PERSONNEL.
presence of uninsulated “dangerous
voltage” within the product’s enclosure
that may be sufficient magnitude to
constitute a risk of electric shock to
persons.
The exclamation point within an
equilateral triangle is intended to alert
the user to the presence of important
operating and maintenance (servicing)
instructions in the literature
accompanying the appliance.
The asterisk within an equilateral
triangle is intended to inform the user to
necessary installation or removal
instructions regarding equipment or
hardware use relating to the system.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer's
instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug
has two blades with one wider than the other. A grounding type plug has two blades and
a third grounding prong. The wide blade or the third prong is provided for your safety. If
the provided plug does not fit into your outlet, consult an electrician for replacement of
the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or
with the apparatus. When a cart is used, use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
13. Unplug the apparatus during lightning storms or when unused for long periods of time.
2018-11 | 04 | F.01U.341.540 Installation manual Electro-Voice
EVOLVE 50 Portable Column System Safety | en 5
!
!
14. Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is damaged,
liquid has been spilled or objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has been dropped.
15. No naked flame sources, such as lighted candles, should be placed on the apparatus.
16. To reduce the risk of fire or electric shock, do not expose this apparatus to rain or
moisture. The apparatus should not be exposed to dripping or splashing. Objects filled
with liquids, such as vases should not be placed on apparatus.
17. Do not block any ventilation openings. Install in accordance with the manufacturer's
instructions.
18. Minimum 60 cm (2 ft) distances around the apparatus for sufficient ventilation.
19. The ventilation should not be impeded by covering the ventilation openings with items,
such as newspapers, table-cloths, curtains, etc.
20. To completely disconnect AC power from this apparatus, the power supply cord must be
unplugged.
Warning!
This product is not designed to be suspended. Do NOT use handles or any other method to
suspend the loudspeaker. Handles on Electro-Voice loudspeakers are intended to only be
used for temporary transport by people.
Items, such as fiber rope, wire rope, cables, or other types of materials cannot be used to
suspend loudspeaker from the handles.
Caution!
Do not attempt to move this loudspeaker system when it is fully assembled.
You may damage the system or cause personal injury.
1.2 FCC information
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause
undesired operation.
Electro-Voice Installation manual 2018-11 | 04 | F.01U.341.540
6 en | Safety EVOLVE 50 Portable Column System
Notice!
This product has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This product generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this product does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/TV technician for help.
The device contains a BT module CYBLE-022001-00 which has been granted by FCC and IC,
the FCC ID:WAP2001 and IC:7922A-2001. And module is assembled on the PRE PCB
Please take attention that changes or modification not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
This equipment should be installed and operated with a minimum distance 20cm between the
radiator and your body
This device complies with Industry Canada license-exempt RSS standard(s). Operation is
subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired
operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils
radioexempts de licence. L'exploitation est autorisée aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna
of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To
reduce potential radio interference to other users, the antenna type and its gain should be so
chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that
necessary for successful communication.
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut
fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour
l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage
radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain
de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité
nécessaire à l'établissement d'une communication satisfaisante.
2018-11 | 04 | F.01U.341.540 Installation manual Electro-Voice
EVOLVE 50 Portable Column System Safety | en 7
!
!
!
!
1.3 Precautions
If an Electro-Voice loudspeaker is used outdoors on a sunny day, place the
loudspeaker in a shaded or covered area. The loudspeaker amplifiers have
protection circuits that temporarily shut the loudspeaker off when extremely
high temperatures are reached. This can happen on hot days when the
loudspeaker is in direct sunlight.
Do not use Electro-Voice loudspeakers in an environment where temperatures
are below 0°C (32°F) or exceed +35°C (95°F).
Never expose an Electro-Voice loudspeaker to rain, water, or high moisture.
Electro-Voice loudspeakers are easily capable of generating sound pressure
levels sufficient to cause permanent hearing damage to anyone within normal
coverage distance. Caution should be taken to avoid prolonged exposure to
sound pressure levels exceeding 90 dB.
1.4 Certifications
Brazil:
"Este equipamento não tem direito à proteção contra interferência prejudicial e não pode
causar interferência em sistemas devidamente autorizados"
Mexico:
“La operación de este equipo está sujeta a las siguientes dos condiciones: (1) es posible que
este equipo o dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo
debe aceptar cualquier interferencia, incluyendo la que pueda causar su operación no
deseada”
Singapore:
Republic of Korea:
제품명: 앰프내장형 스피커
모델명: EVOLVE50-SB-AP
정격: 100-240Vac, 50-60Hz, 1000W
수입업체(상호)명: 로버트보쉬코리아(유)
제조자: Bosch Security Systems, lnc.
제조연월:별도표기 제조국 : 중국
Electro-Voice Installation manual 2018-11 | 04 | F.01U.341.540
8 en | Safety EVOLVE 50 Portable Column System
A/S: 02-702-2845
해당 무선설비는 운용 중 전파혼신 가능성이 있음
해당 무선설비는 전파혼신 가능성이 있으므로 인명안전과 관련된 서비스는 할 수 없습니다.
United Arab Emirates:
TRA Registered no.: ER58747/17
Dealer no.: DA45733/15
1.5 Notices
Old electrical and electronic appliances
Electrical or electronic devices that are no longer serviceable must be collected separately and
sent for environmentally compatible recycling (in accordance with the European Waste
Electrical and Electronic Equipment Directive).
To dispose of old electrical or electronic devices, you should use the return and collection
systems put in place in the country concerned.
Copyright and disclaimer
All rights reserved. No part of this document may be reproduced or transmitted in any form by
any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior
written permission of the publisher. For information on getting permission for reprints and
excerpts, contact Electro-Voice.
All content including specifications, data, and illustrations in this manual are subject to change
without prior notice.
Notice!
Bluetooth® is available in select countries.
Contact your nearest Electro-Voice dealer or Electro-Voice distributor for more information.
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc.
and any use of such marks by Bosch Security Systems, Inc. is under license. Other trademarks
and trade names are those of their respective owners.
2018-11 | 04 | F.01U.341.540 Installation manual Electro-Voice
EVOLVE 50 Portable Column System Safety | en 9
For use in China: CHINA ROHS DISCLOSURE TABLE
Electro-Voice Installation manual 2018-11 | 04 | F.01U.341.540
10 en | Short information EVOLVE 50 Portable Column System
2 Short information
The following table lists products in a family, with CTN (Commercial Type Number) and
identifying product name DESCRIPTION.
CTN Description
EVOLVE50-TB Column speaker array, pole, black
EVOLVE50-SB-US Column speaker sub US, black
EVOLVE50-SB-EU Column speaker sub EU, black
EVOLVE50-SB-AP Column speaker sub AP, black
EVOLVE50-SB-GL Column speaker sub, black, global, no BT
EVOLVE50-TW Column speaker array, pole, white
EVOLVE50-SW Column speaker sub, white, global w BT
EVOLVE50-SW-GL Column speaker sub, white, global, no BT
EVOLVE50-PL-SB Column speaker pole, short, black
EVOLVE50-PL-SW Column speaker pole, short, white
EVOLVE50-CASE Column speaker carrying case, wheels
EVOLVE50-SUBCVR Subwoofer cover
2.1 Shipping contents
Quantity Component
1 Subwoofer
1 Power cord
1 Installation manual
1 Warranty card
1 Safety manual
Tab.2.1: Subwoofer box (EVOLVE50-US, EVOLVE50-EU, and EVOLVE50-AP models)
Quantity Component
1 Subwoofer
2 Power cords
1 Installation manual
1 Warranty card
1 Safety manual
Tab.2.2: Subwoofer box (EVOLVE50-SB-GL, EVOLVE50-SW, and EVOVLVE50-SW-GL models)
2018-11 | 04 | F.01U.341.540 Installation manual Electro-Voice
EVOLVE 50 Portable Column System Short information | en 11
Quantity Component
1 Column array
1 Sub pole
1 Carry bag
Tab.2.3: Column array box (EVOLVE50-TB and EVOLVE50-SW models)
Electro-Voice Installation manual 2018-11 | 04 | F.01U.341.540
12 en | Description EVOLVE 50 Portable Column System
3 Description
Thank you for choosing an Electro-Voice portable column system. Please take time to consult
the manual to understand all the features built into your EV system and fully utilize its
performance capabilities.
The EVOLVE 50 portable column system is a new entry and form factor in the Electro-Voice
portable sound portfolio. Designed to deliver an uncompromising combination of low-profile
aesthetics and superior audio performance, the EVOLVE 50 sets a new standard for portable
columnar systems.
EVOLVE 50 is designed to quickly and easily be transported and assembled. The three handle
design on the subwoofer and convenient included carry case for the sub pole and column
array provide minimal resistance to getting excellent, professional sound anywhere you need
it. Installation is made easier via the symmetrical aluminum subwoofer pole with an integrated
wire assembly. The connection is secured by the magnetic assisted latching system, which
magnetically locks the sub pole in place.
The full-range column array and its eight 3.5-inch neodymium drivers are directed using
custom-designed waveguides for consistent 120° coverage. The ported subwoofer enclosure
houses a 12-inch woofer that is supported by 18 mm wood for enhanced stiffness and
acoustical performance. The Class-D amplifier provides up to 1000 watts of output power: 500
watts to the subwoofer and 500 watts to the column array. The input panel features EV's
industry-leading QuickSmartDSP interface—allowing intuitive navigation of system parameters
via an LCD with single-knob control—as well as multiple options for signal routing and inputs.
The new Electro-Voice QuickSmart Mobile application utilizes Bluetooth® Low Energy (BTLE)
technology for the wireless configuration, control, and monitoring of up to six EVOLVE 50
systems simultaneously. High-resolution Bluetooth® audio streaming adds convenience for
wireless music playback in breakout rooms, intermission, and musical accompaniment.
Bluetooth® is available in select countries.
Electro-Voice quality and testing procedures far exceed the industry norm to yield efficient
and effective electro-acoustic performance; this creates components that deliver an accurate,
linear response at the system’s highest output levels. When applied to EVOLVE 50, this
engineering philosophy results in a system that brings a new sonic benchmark to the column
speaker segment, all packaged in a sleek and portable enclosure that blends into the
background in any application from a lounge to a wedding reception.
3.1 System features
– EV QuickSmart Mobile application: quickly and wirelessly configure, control, and monitor
up to six EVOLVE 50 systems simultaneously, and receive immediate notification during
critical performance conditions. Bluetooth® connectivity is available in select countries.
– High-quality Bluetooth® audio streaming for background music or musical
accompaniment. Bluetooth® connectivity is available in select countries.
– Ultra-wide 120° horizontal coverage via custom-designed waveguides and array-formed
40° asymmetrical vertical coverage means all acoustical energy is directed towards both
sitting and standing audiences.
2018-11 | 04 | F.01U.341.540 Installation manual Electro-Voice
EVOLVE 50 Portable Column System Description | en 13
FUSE T5AL/250V
REPLACE AS M ARKED
OPERATING VO LTAGE / TEGANGAN:
100-240V AC / 50-60 Hz
MAINS I N
POWER
ON
OFF
– QuickSmartDSP provides best-in-class processing via EV's signature single-knob user
interface with LCD. Easy setup via four presets (Music, Live, Speech, Club), three-band
EQ (low, mid, high), five user-programmable presets (Store and Recall settings), output
delay, phantom power, visual monitoring of limiter status, input level control and meters,
and master volume control to optimize gain structure.
– Ideal for portable applications. Light weight and intuitive assembly via the magnet
assisted sub pole make a quality performance easier than ever.
3.2 Quick setup
Subwoofer
To set up a subwoofer, do the following:
Step Illustration
1. Connect the AC power cord from a
grounded line receptacle to the MAINS IN.
2. Connect the XLR or TRS cables from an
audio source to INPUT 1 or INPUT 2 or
connect the RCA cable or 3.5 mm mini jack
from an audio source to INPUT 3.
3. Adjust the input gain to (infinity).
4. Switch POWER to ON.
5. From the DSP home screen, increase the
input gain to the desired sound output.
6. Adjust the MASTER VOL knob to the
desired volume.
See also
– Amplifier DSP, page 15
Electro-Voice Installation manual 2018-11 | 04 | F.01U.341.540
14 en | Installation EVOLVE 50 Portable Column System
!
A
A
4 Installation
Caution!
Do not attempt to move this loudspeaker system when it is fully assembled.
You may damage the system or cause personal injury.
Assembling the loudspeaker system
To assemble the loudspeaker system, do the following:
1. Place the subwoofer on a level and stable surface.
2. Insert the symmetrical pole into the top of the subwoofer.
The pole has magnets (A) at each end. The pole can be inserted on either end.
3. Place the column array loudspeaker on top of the subwoofer pole.
4. The column array loudspeaker system set up is complete.
2018-11 | 04 | F.01U.341.540 Installation manual Electro-Voice
EVOLVE 50 Portable Column System Amplifier DSP | en 15
1 2 43
5 9876
5 Amplifier DSP
5.1 Amplifier DSP controls
The amplifier has a combination of controls and connectors to ensure the most versatile
loudspeaker system.
Portable column system control and monitoring interface
The portable column system DSP control menu selections are available for the EVOLVE 50 .
1. LCD – DSP control and monitoring interface.
2. MASTER VOL – Adjusts the sound level.
DSP – Scroll through the menu and select the available choices. Push the MASTER VOL
knob to enter the DSP menu.
3. LINE | MIC – Electronically balanced INPUT 1 and INPUT 2 MIC/LINE for the connection of
a line level signal source (such as mixer etc.) or a microphone. Phantom power (+15 V)
can be enabled Phantom 1 or 2 if a condenser microphone is being used. Establishing a
connection is possible via TRS or XLR-type plugs. Whenever possible, balanced signal
feed is always preferable to guard against potential noise or HF-interference. This control
lets you optimally adjust the incoming signals to match the sensitivity of the system.
4. AUX IN – Control to adjust the input trim of the stereo RCA type, 3.5mm, or Bluetooth®
streaming inputs. This control lets you optimally adjust the incoming signals to match the
sensitivity of the system. Bluetooth®connectivity is available in select countries.
5. MIX OUT – The post-fader audio signals of INPUT 1, INPUT 2 and INPUT 3 are mixed and
passed to MIX OUT. The ratio of the input signals changes when the level controls INPUT
1, 2 or 3 are adjusted. This feature allows the loudspeaker to act as a basic three-channel
mixer that can send the mix to another loudspeaker via the MIX OUT socket. This output
is laid out in GND-SENSING technology, a special pin assignment of the output socket,
offering all advantages of the balanced signal transmission, but lets you also connect
monaural plugs without a problem.
6. THRU – The THRU output socket is connected in parallel to INPUT 1, it is used for carrying
through the pre-fader input signal to additional powered loudspeaker or subwoofer.
7. INPUT – Electronically balanced INPUT 1/2 MIC/LINE for the connection of a line level
signal source (such as mixer etc.) or a microphone. Establishing a connection is possible
via TRS or XLR-type plugs. Whenever possible, balanced signal feed is always preferable
to guard against potential noise or HF-interference.
8. INPUT 3 RCA Connector – Stereo unbalanced RCA type INPUT 3 AUX IN for connecting
sources such as CD players or MP3 players.
Electro-Voice Installation manual 2018-11 | 04 | F.01U.341.540
16 en | Amplifier DSP EVOLVE 50 Portable Column System
EVOLVE 50
F
U
SE T5AL/250V
REPLACE AS MARKED
OPERATING VOLTAGE / TEGANGAN:
100-240V AC / 50-60 Hz
MAINS IN
POWER
ON OFF
BOSCH SICHERHEITSSYSTEME GMBH
85626 GRASBRUNN, GERMANY
BOSCH SECURITY SYSTEMS, INC
14450 FAIRPORT, NY, USA
FOR INDONESIA ONLY:
IMPORTED BY / DIIMPOR OLEH
PT ROBERT BOSCH
JAKARTA, INDONESIA
www.electrovoice.com | MADE IN CHINA
10
11
IN1
IN
2
LEVEL 0dB
C
1
IN3
1
2
3
4
5
6
7
8
S
E
9. INPUT 3 3.5mm connector – Balanced mono or unbalanced stereo input for mobile
phones, laptops, etc.
Notice!
Markings and statements on amplifier panel may vary.
5.2 System status
2018-11 | 04 | F.01U.341.540 Installation manual Electro-Voice
10. MAINS IN – The device receives its power supply via the MAINS IN socket. Only the
provided power cord may be used. Connect the device only to a mains network, which
corresponds to the requirements indicated on the type plate.
11. POWER – AC switch for switching the power ON or OFF. The LCD screen lights up when
the power is turned ON, after approximately 3 seconds.
Normal
Figure5.1: Normal system status home screen with Bluetooth® status
1. LEVEL – Indicates the master gain of the system in dB. The range is from mute to +10 dB,
in 1 dB increments.
2. IN1 – VU meter displays the signal level of INPUT 1 into the amplifier INPUT 1 XLR
connector. IN1 and IN2 are independent of each other.
3. IN2 – VU meter displays the signal level of INPUT 2 into the amplifier INPUT 2 XLR
connector. IN1 and IN2 are independent of each other.
4. IN3 – VU meter displays the signal level of INPUT 3.
5. C - Control app; the available options are:
OFF - DISABLED
FLASHING - PAIRING MODE
SOLID - CONNECTED
6. 1 - Indicates the selected store function number. There are five user defined store
function numbers available.
7. E - Indicates the preset is not saved. When the preset is saved the E is not displayed.
8. S - Audio streaming; the available options are:
OFF - DISABLED
EVOLVE 50 Portable Column System Amplifier DSP | en 17
FLASHING - PAIRING MODE (120s)
SOLID - CONNECTED
Notice!
Bluetooth® is available in select countries.
Contact your nearest Electro-Voice dealer or Electro-Voice distributor for more information.
System protection
System protection limiters indicate when a system is exceeding recommended usage by
indicating CLIP or LIMIT on the LCD display.
CLIP
CLIP indicates the signal to the loudspeaker is too high, resulting in a clipped signal into the
loudspeaker. If CLIP is shown, reduce the input gain knob and/or the signal on the mixer or
source equipment.
LIMIT
LIMIT protects the loudspeaker from short-term peaks which can cause distortion. When
LIMIT is shown small on the screen, the limiter is active but keeps distortion under control.
The large LIMIT indicates the sound is negatively affected. Reducing the output volume
(MASTER VOL) is strongly recommended when the large limit indication is shown.
See also
– Pairing the QuickSmart Mobile application, page 23
5.3 DSP control menu
EXIT
MODE MUSIC (Default)
SUB LEVEL 0 dB (Default)
TREBLE 0 dB (Default)
MID 0 dB (Default)
MID FREQ 1200 Hz (Default)
LIVE
SPEECH
CLUB
Mute, -80 dB to +10 dB
-12 dB to +6 dB
-12 dB to +6 dB
200 to 12000 Hz
BASS 0 dB (Default)
-12 dB to +6 dB
PHANTOM 1 ON
OFF (Default)
Electro-Voice Installation manual 2018-11 | 04 | F.01U.341.540
18 en | Amplifier DSP EVOLVE 50 Portable Column System
PHANTOM 2 ON
OFF (Default)
MIX OUT L+R (Default)
R
DELAY FEET OFF (Default)
METERS
OFF, 0.1 to 100.0 m (and ft.)
LED OFF
ON (Default)
LIMIT
CONTROL APP
DISPLAY BACK
LCD DIM ON (Default)
OFF
BRIGHT 5 (Default)
1 to 10
CONTRAST 5 (Default)
1 to 10
BACK
STORE EXIT, 1, 2, 3, 4, 5, EXIT
RECALL EXIT, 1, 2, 3, 4, 5, EXIT
BLUETOOTH CONTROL
APP
ON
OFF (Default)
STREAMING PAIRING
ON
OFF (Default)
RESET RESET ALL SETTINGS?
NO (Default)
YES
INFO [PRODUCT NAME]
[FIRMWARE VERSION]
©2017 Electro-Voice
EXIT
Tab.5.4: Portable column system DSP Control Menu
2018-11 | 04 | F.01U.341.540 Installation manual Electro-Voice
EVOLVE 50 Portable Column System Amplifier DSP | en 19
EXIT Menu
The Exit menu is used to return to the home screen.
Notice!
The display returns to the home screen after two minutes of inactivity.
MODE Menu
The Mode menu is used to configure the type of sound the subwoofer delivers.
– MUSIC – is used for recorded music playback and electronic dance music applications.
(Default)
– LIVE – is used for live sound applications.
– SPEECH – is used for spoken word applications.
– CLUB – is used for recorded electronic music playback.
SUB LEVEL Menu
The Sub Level menu allows independent gain control of the subwoofer output. Changes to
this parameter effectively change the crossover of the EVOLVE 50 system. The default setting
of 0 dB is recommended for best audio performance.
The range is MUTE, -80 dB to +10 dB.
The default is 0 dB.
TREBLE Menu
The Treble menu is used to adjust the high frequency performance of the loudspeaker for
different applications or personal preference. The parameter controls a high shelving filter
that is centered on 6 kHz.
The range is -12 dB to +6 dB.
The default is 0 dB.
MID Menu
The MID menu is used to set the gain of the MID peak filter.
The range is -12 dB to +6 dB.
The default is 0 dB.
MID FREQ Menu
The MID Freq menu is used to set the center frequency of the MID peak filter.
The range is 200 -12000 Hz.
The default is 1200 Hz.
BASS Menu
The Bass menu item is used to configure the low frequencies of sound.
The range is -12 dB to +6 dB.
The default is 0 dB.
PHANTOM 1 or PHANTOM 2 Menu
The Phantom 1 or Phantom 2 menu is for activating phantom power (+15 V) of audio INPUT 1
or 2 whenever a suitable condenser microphone is being used. Available options for this
selection are: ON or OFF.
The default is OFF.
MIX OUT Menu
The Mix Out menu is used to select which signal of INPUT 3 AUX IN should be output at MIX
OUT and which signal should be delivered by the loudspeaker.
Electro-Voice Installation manual 2018-11 | 04 | F.01U.341.540
20 en | Amplifier DSP EVOLVE 50 Portable Column System
– L+R: The left and right signals of INPUT 3 are summed. The sum is output at MIX OUT and
is delivered by the loudspeaker. (Default)
– R: Only the right signal of INPUT 3 is output at MIX OUT. The loudspeaker will deliver only
the left signal.
DELAY Menu
The Delay menu is used to delay the output signal, e.g. to compensate for differences in
distance among individual loudspeakers. The delay can be set in meters or feet. Available
options for this selection are: OFF or a delay up to 100.0 m or 328 ft. The delay can be
changed in 0.1 meter increments or 0.1 foot increments.
The default is OFF.
DISPLAY Menu
The Display menu options are BACK, LCD DIM, BRIGHT, and CONTRAST.
LED Menu
The LED menu shows power on and indicates limit. Available options for this selection are:
ON, OFF, LIMIT or CONTROL APP.
– ON – turns the LED on when the power to the loudspeaker is ON. (Default)
– OFF – turns the LED off.
– LIMIT – turns the LED off under normal operation. The LED brief blinking indicates the
limiter is activating. Short-term blinking is not critical because the integrated limiter
keeps distortion under control. Constant lighting of the LED indicates the sound is
negatively affected. If the LED is constantly lit, check the rear LCD for more information.
Reducing the output volume is strongly recommended.
– CONTROL APP – indicates if Bluetooth® on the portable column system is trying to pair
or is connected to a Bluetooth® enabled mobile device. In pairing mode the LED will flash
blue indicating it is ready to pair. The LED is solid blue when it is connected.
The default is ON.
LCD DIM Menu
The LCD Dim menu is used to dim the display when the display is idle for 30 seconds.
Available options for this selection are: ON or OFF.
The default is ON.
BRIGHT Menu
The Bright menu is used to determine the brightness of the LCD.
The range is 1 to 10.
The default is five (5).
CONTRAST Menu
The Contrast menu is used to increase or decrease the visibility of the LCD screen.
The range is 1 to 10.
The default is five (5).
STORE Menu
The Store menu allows you create up to five customized user settings. Available options for
this selection are: EXIT, 1, 2, 3, 4, and 5.
Notice!
The customized user setting name can contain a combination of alphanumeric characters
including spaces. The alphanumeric character range is A to Z and 0-9.
The name field length is 12 characters.
2018-11 | 04 | F.01U.341.540 Installation manual Electro-Voice
EVOLVE 50 Portable Column System Amplifier DSP | en 21
Storing customized user settings
To store customized user settings, do the following:
1. From the DSP menu, scroll to STORE.
2. Push the MASTER VOL knob to select STORE.
The store screen appears.
3. Push the MASTER VOL knob to select 1.
The Enter name for 1 screen appears.
4. Use the MASTER VOL knob to scroll through the characters.
The characters appear.
5. Push the MASTER VOL knob to select the desired character.
6. Turn the MASTER VOL knob to move to the next character entry.
Continue selecting characters until the desired name is entered.
7. Use the MASTER VOL knob to scroll to SAVE.
8. Push the MASTER VOL knob to select SAVE.
9. Repeat steps 3 through 8 to store additional customized user settings.
10. Select EXIT to return to the home screen.
RECALL Menu
The Recall menu allows you retrieve up to five customized user settings. Available options for
this selection are: EXIT, 1, 2, 3, 4, and 5.
Recalling customized user settings
To recall customized user settings, do the following:
1. From the DSP menu, scroll to RECALL.
2. Push the MASTER VOL knob to select RECALL.
The recall screen appears.
3. Push the MASTER VOL knob to select 1.
The selected item is loaded.
4. Select EXIT to return to the home screen.
BLUETOOTH
The Bluetooth menu options are CONTROL APP and STREAMING.
CONTROL APP Menu
The Control App menu is used to enable the QuickSmart Mobile wireless control and
monitoring application. Available options for this selection are: ON or OFF.
The default is OFF.
Notice!
Bluetooth® is available in select countries.
Contact your nearest Electro-Voice dealer or Electro-Voice distributor for more information.
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc.
and any use of such marks by Bosch Security Systems, Inc. is under license. Other trademarks
and trade names are those of their respective owners.
Turning Bluetooth® ON or OFF
To turn Bluetooth® ON or OFF, do the following:
1. From the DSP menu, scroll to CONTROL APP.
2. Select ON.
OR
Select OFF.
Electro-Voice Installation manual 2018-11 | 04 | F.01U.341.540
22 en | Amplifier DSP EVOLVE 50 Portable Column System
STREAMING
The Streaming menu is used to stream audio from your Bluetooth® enabled device to the
loudspeaker system. Available options for this selection are: PAIRING, ON or OFF.
The default is OFF.
Pairing the portable column system with your Bluetooth® enabled device
To pair the portable column system with your Bluetooth® enabled device, do the following:
1. From the DSP menu, scroll to STREAMING.
2. Select PAIRING.
PAIRING mode enables 120 seconds of visibility to Bluetooth® enabled devices.
3. On your mobile device, select EV EVOLVE to initiate the pairing process.
Once the device is paired, all device audio will be output through the EVOLVE 50 system.
Notice!
If connected with a mobile device, notification alerts and ring tones will also be played
through the system.
Disable these notifications or enable Airplane mode on your mobile device to prevent
unwanted interruptions during audio playback.
Turning streaming ON or OFF
To turn streaming ON or OFF, do the following:
1. From the DSP menu, scroll to STREAMING.
2. Select ON.
OR
Select OFF.
RESET Menu
The Reset menu is used to reset the loudspeaker to original factory settings. Available options
for this selection are: NO or YES.
The default is NO.
Resetting the system
To reset the system to original factory settings, do the following:
1. From the DSP menu, select RESET.
The "RESET ALL SETTINGS?" validation message appears.
2. Select YES.
The system is reset to the original factory settings.
Notice!
The reset menu item is used to revert the loudspeaker to the original factory default settings.
All user settings will be deleted. The user customized settings in the STORE and RECALL
menus return to <EMPTY>.
INFO Menu
The Information menu is used to display the product name and firmware version.
See also
– Pairing the QuickSmart Mobile application, page 23
2018-11 | 04 | F.01U.341.540 Installation manual Electro-Voice
EVOLVE 50 Portable Column System Pairing the QuickSmart Mobile application | en 23
6 Pairing the QuickSmart Mobile application
The EV QuickSmart Mobile app is available for download for the iOS 10 and higher tablets and
smart phones from the iTunes App Store or Android Marshmallow and higher tablets and
smart phones from the Google Play Store.
Notice!
The EV QuickSmart Mobile app is designed to only find speakers from Electro-Voice with
Bluetooth® enabled.
The EV QuickSmart Mobile app will not display other types of Bluetooth® devices, e.g.
phones, laptops, tablets, or headsets.
Notice!
Bluetooth® is available in select countries.
Contact your nearest Electro-Voice dealer or Electro-Voice distributor for more information.
Prior to pairing the EV QuickSmart Mobile app with loudspeakers by Electro-Voice ensure
Bluetooth® is enabled on the smart phone or tablet, and the loudspeaker.
First time pairing:
To pair the loudspeaker with the EV QuickSmart Mobile app, do the following:
1. Open the EV QuickSmart Mobile app.
2. Finding nearby speakers is displayed on the screen
The EV QuickSmart Mobile app is looking for available Bluetooth® enabled Electro-Voice
loudspeakers.
3. The available loudspeakers are displayed on the screen.
The app will display up to eight available loudspeakers.
4. Tap the loudspeaker you want to pair with the app.
The selected loudspeaker will have a red line under it acknowledging it is selected.
5. Repeat the previous step until all of the desired loudspeakers are selected.
6. Tap the red CONNECT button.
7. The app pairs with the desired loudspeaker.
The app can connect to up to six loudspeakers.
Subsequent pairing:
To pair the loudspeaker with the EV QuickSmart Mobile app, do the following:
1. Tap the EV QuickSmart Mobile app icon.
2. Finding nearby speakers is displayed on the screen
The EV QuickSmart Mobile app is looking for available Bluetooth® enabled Electro-Voice
loudspeakers.
3. The available loudspeakers are displayed on the screen.
The app will display up to eight available loudspeakers.
4. Tap the loudspeaker you want to pair with the app.
The selected loudspeaker will have a red line under it acknowledging it is selected.
5. Repeat the previous step until all of the desired loudspeakers are selected.
6. Tap the red CONNECT button.
7. The app pairs with the desired loudspeaker.
The app can connect to up to six loudspeakers.
Electro-Voice Installation manual 2018-11 | 04 | F.01U.341.540
24 en | Recommended configurations EVOLVE 50 Portable Column System
LR
7 Recommended configurations
7.1 Stereo pair of EVOLVE 50 systems
R Right
L Left
Notice!
The direction of the arrow indicates the signal path.
Mode: Music
MIX-OUT: R
Tab.7.5: DSP settings for the portable column system
See also
– DSP control menu, page 17
2018-11 | 04 | F.01U.341.540 Installation manual Electro-Voice
EVOLVE 50 Portable Column System Recommended configurations | en 25
B
A
7.2 Solo musician performance
A Guitar, conga drum, etc.
B Condenser microphone
Notice!
The direction of the arrow indicates the signal path.
Mode: Live
Phantom 1: On
Tab.7.6: DSP settings for the portable column system
See also
– DSP control menu, page 17
Electro-Voice Installation manual 2018-11 | 04 | F.01U.341.540
26 en | Troubleshooting EVOLVE 50 Portable Column System
8 Troubleshooting
Problem Possible cause Action
1. No sound Amplifier Verify all the electronics are on, the signal
routing is correct, the source is active; the
volume is turned up, etc.
Correct/repair/replace as necessary. If there is
still no sound, the problem may be wiring.
Wiring Verify you have connected the correct cables to
the amplifier. Play something at a low level
through the amplifier. Connect a test
loudspeaker in parallel with the malfunctioning
line. If the sound level is gone or is very weak,
the line has a short in it (possibly a severe
scrape, pinch, or a missed connection). Using
the test loudspeaker, move down the line and
test each connection/junction until you find the
problem and correct it. Observe proper
polarity.
2. Intermittent
output such as
crackling or
distortion
3. Constant noise
such as
buzzing hissing
or humming
4. No sound
produced with
microphone
connected to
INPUT 1 or
INPUT 2
Faulty connection Check all connections at amplifier and
loudspeakers to ensure they are all clean and
tight. If the problem persists, check the wiring.
See problem 1.
Defective source or
other electronic
device
Poor system
grounding or ground
loop
Input gain knob is not
in the MIC position
Microphone requires
phantom power.
Input gain knob is not
in the MIC position
If noise is present, but no program material is
playing, evaluate each component as necessary
to isolate the problem. Most likely there is a
break in the signal path.
Check and correct the system grounding, as
required.
Slowly increase the input gain knob level to
engage the microphone pre-amp.
Use a dynamic microphone that does not
require phantom power (+15 V). If using a
microphone requiring phantom power, enable
PHANTOM POWER is the DSP menu, or use an
external phantom power source.
Slowly increase the input gain knob level to
engage the microphone pre-amp.
5. Sound is
distorted front
LED is OFF,
LCD screen
LIMIT is ON
2018-11 | 04 | F.01U.341.540 Installation manual Electro-Voice
Excessive input level Reduce the input level or loudspeaker level
knobs to prevent limit.
EVOLVE 50 Portable Column System Troubleshooting | en 27
Problem Possible cause Action
6. Microphone
produces
acoustic
feedback when
input level is
amplified
7. DSP menu is
locked
8. QuickSmart
Mobile app
does not
detect the
loudspeaker
Incorrect gain
structure or source
input (mixing console/
preamp) is overdriven
Verify level controls of the source are properly
structured by using the VU meter indicator on
the LCD screen. If the VU meter bar is solid or
the system indicates LIMIT, the input or source
level is too high.
Incorrect gain
structure
Reduce the microphone levels at the mixing
console or input source. If the microphone is
connected directly to the speaker, reduce the
input level on the speaker. Positioning the
microphone close to the sound source
increases gain-before-feedback. See problem 6.
MODE is set to MUSIC Change the MODE to LIVE or SPEECH.
Microphone position
is too close to the
front of the
loudspeaker
The Menu Lock
function has been
Whenever possible setup the loudspeakers so
the microphone is behind them. If using the
loudspeaker in a monitor position, aim the
loudspeaker to the back of the microphone.
Press and hold the MASTER VOL knob for 5
seconds.
turned on.
Enable Bluetooth® Ensure Bluetooth® is enabled on the
loudspeaker.
If these suggestions do not solve your problem, contact your nearest Electro-Voice dealer or
Electro-Voice distributor.
Electro-Voice Installation manual 2018-11 | 04 | F.01U.341.540
28 en | Technical data EVOLVE 50 Portable Column System
9 Technical data
Frequency response (-3 dB)1: 43 Hz-20 KHz
Frequency range (-10 dB)1: 37 Hz-20 KHz
Maximum SPL2: 127 dB
Coverage (H x V): 120° x 40°
Amplifier rating: 1000 W
LF channel rating: 500 W
HF channel rating: 500 W
Crossover frequency: 200 Hz
Connectors: 2x XLR/TRS Combo Jack Input
1x 3.5 mm Input
1x Stereo RCA Input
1x Wireless Bluetooth® Audio Input
1x XLR THRU Output
1x XLR MIX OUT Output
Enclosure: Sub: 15 mm plywood
Column: Composite
Pole: Aluminum
Grille: Steel with black or white powder coat
Color: Black or white
Dimensions (HxWxD):
mm (in)
Sub: 530 x 345 x 471 (20.9 x 13.6 x 18.5)
Column: 825 x 102 x 172 (32.5 x 4.0 x 6.9)
Pole: 929 x 48.5 x 55 (36.6 x 1.9 x 2.2)
Net weight: Sub: 44.66 lb (20.3 kg)
Column: 10.34 lb (4.7 kg)
Pole: 2.75 lb (1.25 kg)
Sub cover: 0.9 lb (0.4 kg)
Bag for column and pole: 1.87 (0.85 kg)
Shipping weight: Sub box: 50.71 lb (23 kg)
Column box: 18.30 lb (8.3 kg)
Power consumption3: 100-240 V AC, 50-60 Hz, 1.5-0.6 A
1
Full-space measurement using music DSP preset.
2
Maximum SPL is measured at 1 m using broadband pink noise at maximum output.
3
Current rating is 1/8 power.
2018-11 | 04 | F.01U.341.540 Installation manual Electro-Voice
EVOLVE 50 Portable Column System Technical data | en 29
345 mm
530.0 mm470 mm
492 mm
7 mm
930 mm
55 mm
48.5 mm
38.5 mm
789 mm
68 mm
37.9 mm
29.7 mm
102 mm
825 mm
121.2 mm
102.4 mm
102 mm
157.2 mm
121.2 mm
172.0 mm
108.7 mm
[13.58 in]
[6.8 in]
[6.2 in]
[4.8 in]
[4.0 in]
[32.5 in]
[4.0 in] [4.3 in]
[4.0 in]
[4.8 in]
[31.1 in]
[36.6 in]
[2.7 in]
[1.5 in]
[1.2 in]
[2.2 in]
[1.9 in]
[1.5 in]
[0.3 in]
[19.4 in]
[20.9 in]
[18.5 in]
471 mm
[18.54 in]
54.5 mm
2.1 in
48 mm
1.9 in
159 mm
6.3 in
319 mm
12.6 in
80 mm
3.1 in
9.1 Dimensions
Figure9.1: Dimensions EVOLVE 50 (subwoofer left, spacer center, and column right)
Figure9.2: Dimensions EVOLVE 50 short pole
Electro-Voice Installation manual 2018-11 | 04 | F.01U.341.540
30 en | Technical data EVOLVE 50 Portable Column System
9.2 Frequency response
Figure9.3: Frequency response EVOLVE 50 (Live Mode, Music Mode, Speech mode, and Club Mode)
2018-11 | 04 | F.01U.341.540 Installation manual Electro-Voice
Bosch Sicherheitssysteme GmbH
Robert-Bosch-Ring 5
85630 Grasbrunn
Germany
www.boschsecurity.com
© Bosch Sicherheitssysteme GmbH, 2018
Bosch Security Systems, Inc
12000 Portland Avenue South
Burnsville MN 55337
USA
www.electrovoice.com
Loading...