Electro-Voice CPSM EDS User Manual

CPSM

Shock-Mount Kit
for CP212 and CP218
Microphones

• Virtually eliminates
mechanically transmitted noise
from the mounting surface

• More than 15 dB of mechnical
shock isolation
at 200 Hz

• Provides theft-resistant mounting
of CP212 and CP218 microphones

• Mounts in panels up to

1

/2 inches thick

1

Description

The CPSM shock-mount kit is a permanent
mounting accessory providing shock isola­tion for the CP212 and CP218 podium mi­crophones. The amount of isolation is sub­stantial, in excess of 15 dB at 200 Hz (see
Figure 1). The CPSM is also theft resistant
after installation, with the microphone locked
to the shock mount’s sleeve insert. Mount­ing a CP212 or CP218 to a podium, lectern
or desk top is quick and easy using the CPSM
shock-mount kit.

The CPSM kit consists of a shock mount,
template, set screw, hex-key wrench and
three screws. It is designed for installation
into panels up to 1

Installation

1. Select the microphone location by first
checking for obstructions under the panel that
will interfere with the microphone, and for a
flat surface on which to properly seat the top
flange. Panel thickness may not exceed 1
inches (38.1 mm).

2. Clean the surface of the panel on which
the shock mount is to be installed.

3. Crack and peel off the protective back­ing of the template and carefully place the

1

/2 inches thick.

1

template on the panel surface at the chosen
location for the shock mount.

3

4. Drill a 1
mately 39.4 mm) through the center of the
template.

5. Drill three holes for the #6 wood screws.
The hole size for these screws will depend
on the panel material.

6. Set the roll-off switch on the microphone
for the desired response.

7. Insert the microphone into the shock
mount. Turn the microphone so that the plas­tic roll-off switch holder and the switch do
not come in contact with the set screw. In­sert the microphone to the top of the
microphone’s electronics housing, as shown
in the photograph. (The top of the electron­ics housing is the junction just above the
three holding set screws.)

8. Mount the kit’s set screw on the pro­vided hex-key wrench. Insert the set screw
into the tapped hole in the steel sleeve and
tighten, securing the microphone in the shock

/

mount.

2

9. Connect the female 3-pin connector to
the microphone. If depth is restricted, a right­angle audio connector may be required. Place
the shock mount into the drilled hole. Align
the shock mount with the three drilled holes.

/8-inch diameter hole (approxi-

Secure the assembly to the panel by screw­ing in the three remaining wood screws.

Architects’and Engineers’ Specifications

The shock mount shall have a minimum of
15 dB of shock isolation at a frequency of
200 Hz in the vertical axis.

Dimensions shall be 2.06 inches (52.32 mm)
diameter and 1.29 inches (32.77 mm) high.
Net weight shall be 1.21 ounces (34.35
grams). The shock mount shall have a non­reflecting black polycarbonate plastic outer
flange that fits into a hole of 1
mm) in diameter and is secured to a desk
top by three screws; two butyl rubber shock
mounts; and a nickel-plated steel inner sleeve
that captures the microphone and acts as a
theft-resistant security device.

The Electro-Voice CPSM shock mount is
specified.

Limited Warranty

Electro-Voice products are guaranteed
against malfunction due to defects in mate­rials or workmanship for a specified period,
as noted in the individual product-line
statement(s) below, or in the individual prod­uct data sheet or owner’s manual, beginning
with the date of original purchase. If such

3

/8 inches (39.4

CPSM/Shock-Mount Kit for CP212 and CP218 Microphones

malfunction occurs during the specified pe­riod, the product will be repaired or replaced
(at our option) without charge. The product
will be returned to the customer prepaid. Ex-
clusions and Limitations: The Limited
W arranty does not apply to: (a) exterior fin­ish or appearance; (b) certain specific items
described in the individual product-line
statement(s) below, or in the individual prod­uct data sheet or owner’s manual; (c) mal­function resulting from use or operation of
the product other than as specified in the
product data sheet or owner’s manual; (d)
malfunction resulting from misuse or abuse
of the product; or (e) malfunction occurring
at any time after repairs have been made to
the product by anyone other than Electro­Voice Service or any of its authorized ser­vice representatives. Obtaining Warranty

Service: To obtain warranty service, a cus­tomer must deliver the product, prepaid, to
Electro-V oice Service or any of its authorized
service representatives together with proof
of purchase of the product in the form of a
bill of sale or receipted invoice. A list of au­thorized service representatives is available
from Electro-Voice Service at 600 Cecil
Street, Buchanan, MI 49107 (800/234-6831
or FAX [phone]). Incidental and
Consequential Damages Excluded: Prod­uct repair or replacement and return to the
customer are the only remedies provided to
the customer. Electro-Voice shall not be li­able for any incidental or consequential dam­ages including, without limitation, injury to
persons or property or loss of use. Some states
do not allow the exclusion or limitation of
incidental or consequential damages so the

FIGURE 1 —Shock and Vibration
Isolation of the CPSM Shock Mount
(Microphone output referenced
to 1 g acceleration at 200 Hz)

CPSM/Shock-Mount Kit for CP212 and CP218 Microphone

above limitation or exclusion may not apply
to you. Other Rights: This warranty gives
you specific legal rights, and you may also
have other rights which vary from state to
state. Electro-Voice Accessories are guar-
anteed against malfunction due to defects in
materials or workmanship for a period of one
(1) year from the date of original purchase.
Additional details are included in the Uni­form Limited W arranty statement.

For warranty repair or service informa­tion, contact the service repair department
at: 616/695-6831 or 800/685-2606.

For technical assistance, contact Technical
Support at 800/234-6831 or 616/695-6831,
M-F, 8:00 a.m. to 5:00 p.m. Eastern Stan­dard Time.

Specifications subject to change without no­tice.

Specifications
Construction:

Polycarbonate plastic shock mount with
a nickel-plated steel sleeve insert;
mounting flange top surface finished in
non-reflecting black

Recommended For:

CP212 and CP218 podium micro­phones

Maximum Panel Thickness:

1

1

/2 inches (38.1 mm)

Dimensions,
Height:

1.29 inches (32.77 mm)

Width:

2.06 inches (52.32 mm)

Net Weight:

1.21 ounces (34.35 grams)

Shipping Weight:

2.81 ounces (79.55 grams)

600 Cecil Street, Buchanan, MI 49107

616/695-6831, 616/695-1304 Fax

ACCESSORIES—Shock Mount Kit ©EVI Audio 1999 • Litho in U.S.A.

Part Number 531931-9943