Electro-Voice MP1-B, CA-ZX User Instructions

ZX1 Portable Accessories

MP1-B and CA-ZX

User Instructions

MP1-B (P/N 301916-001)

1. Turn the ZX1-90 enclosure upside down, and remove the four #8 screws that attach the rubber feet to the bottom of
the ZX1-90 enclosure with a Phillips screwdriver (Figure 1). The screws will not be needed for the kit, but they will be
needed if you ever want to return the ZX1-90 to its original condition.

2. Remove the four rubber feet from the bottom of the ZX1-90 enclosure (Figure 2).

3. Place the four plastic spacers on the bottom of the ZX1-90 enclosure, and place the steel plate on the plastic spacers
(Figure 3).

4. Place the four rubber feet on the steel plate. Use the four #8 screws supplied with the kit to attach the plastic spacers
and plate to the enclosure (Figure 4). Apply enough torque to each screw so that the rubber foot is bulging slightly.
Do not apply too much torque, as it will damage the rubber foot.

5. Attach the single stud fittings by pressing down on the button, and placing the button through the “dog bone”
openings on the plate (Figure 5). Slide the fittings toward the center of the dog bone until it snaps in place.

Figure 1:

Removing Screws from Bottom of

Enclosure

Figure 3:

Attaching Spacers and Plate to Bottom

of Enclosure

Figure 5:

Attaching Stud Fittings to Steel Plate

Figure 2:

Removing Feet from Bottom of

Enclosure

Figure 4:

Attaching Feet to Steel Plate

WARNING: Suspending any object is potentially
dangerous and should only be attempted by
individuals who have a thorough knowledge of the
techniques and regulations of rigging objects
overhead. Electro-Voice® strongly recommends that
ZX1 speakers be suspended taking into account all
current national, federal, state and local regulations. It
is the responsibility of the installer to ensure that ZX1
speakers are safely installed in accordance with all
such regulations. If ZX1 speakers are suspended,
Electro-Voice® strongly recommends that the system
be inspected at least once a year. If any sign of
weakness or damage is detected, remedial action
should be taken immediately.

CA-ZX (P/N 302023-001)

1. Screw the truss clamp onto the pole mount spigot, using an adjustable wrench (Figure 1).

2. Turn the ZX1-90 enclosure upside down, and remove the setscrew from the back of the pole mount (Figure 2).

3. Insert the truss clamp and pole mount spigot into the pole mount on the ZX1-90 (Figure 3). Screw the eyebolt into the

back of the pole mount. Test that the eyebolt is located in the groove of the spigot properly by pulling on the truss
clamp, tighten eyebolt.

4. Mount the truss clamp to the truss (Figure 4). Securely tighten the clamp. Attach a cable (not included) to the

eyebolt and truss as a safety precaution.

Figure 1:

Screw Truss Clamp to Pole Mount

Spigot

Figure 3:

Attaching Clamp and Spigot to Pole

Mount on Bottom of Enclosure

Figure 2:

Removing Setscrew from Back of Pole

Mount

User Supplied

Safety Cable

Figure 4:

Mounting Truss Clamp to Truss

12000 Portland Avenue South, Burnsville, MN 55337
Phone: [phone], Fax: [phone]

www.electrovoice.com

© Telex Communications, Inc. 12/2005
Part Number 38110-518 Rev 2

U.S.A. and Canada only. For customer orders,

contact the Customer Service department at

Europe, Africa and Middle East only. For customer orders,

For warranty information, contact the Service Repair department at:

For technical assistance, contact Technical Support at:

Specifications subject to change without notice.

800/392-3497 Fax: [phone]

contact the Customer Service department at

49 9421-706 0 Fax: [phone]

616/695-6831 or 800/685-2606

866/78AUDIO