
AB-34 / AB-64 Array Bracket System
Assembly and Installation Instructions
360° Array Bracket Kit
AB-34 and AB-64 series kits feature a 4 sided powder
coated steel mounting assembly that allows the mounting
of 4 EVID speakers into a 360° pattern array configuration. The AB-34 works with the EVID 3.2 series and can
be used with a threaded rod for suspension from the ceiling. The AB-64 is used with the EVID 4.2 or 6.2 series
speakers and can be hung from the ceiling using a threaded
rod or used with a speaker stand tripod as shown. The
EVID’s can then be adjusted using the Strong Arm Mount™
to cover a variety of patterns to best serve the installation
requirements. All assembly hardware is included.
sedulcnItiKtekcarByarrA°0632.4/2.6divE
metI.ytQnoitpircseD
12 2.3divE,tekcarByarrA
21063 ° 2.3divE,retpadAyarrA
302"5.x02-"4/1,wercS
402).aiDedisni"4/1(,rehsaWtalF
50202-"4/1,tuNkcoL
sedulcnItiKtekcarByarrA°0632.3divE
metI.ytQnoitpircseD
12 2.4/2.6divE,tekcarByarrA
21063 ° 2.4/2.6divE,retpadAyarrA
302"5.x02-"4/1,wercS
442).aiDedisni"4/1(,rehsaWtalF
54202-"4/1,tuNkcoL
64 "5.x02-"4/1,wercSdaeHtalF
71 2.4/2.6divE,retpadAdoRdedaerhT
81 tnuoMeloP
Ceiling Suspension (All Sizes)
Step 1: Assemble Array Brackets
Assemble the 2 Array Brackets (Item 1) using 4 Screws (Item 3), 4 Flat Washers (Item 4), and 4 Lock Nuts (Item 5) as
shown in Figure 1.
(Item 3)
Screws
(Item 1)
Array Brackets
(Item 5)
Lock Nuts
(Item 4)
Flat Washers
Figure 1

Ceiling Suspension (Continued)
Step 2: Assemble SAM’s to Array Bracket
Attatch the Strong Arm Mounts™ (SAM) to the Array Bracket (Item 1) using 4 Screws (Item 3), 4 Flat W ashers (Item 4),
and 4 Lock Nuts (Item 5) per SAM as shown in Figure 2. One Screw for each SAM will be used to attatch the 360°
Array Adapter (Item 2).
(Item 4)
Flat
Washers
(Item 5)
Lock Nuts
(Item 2)
360° Array Adapter
Figure 2
Evid 6.2/4.2/3.2 Bracket Assembly
Step 3: Assemble Threaded Rod Adapter to 360°
Array Adapter
Attatch the Threaded Rod Adapter (Item 7) to the 360° Array
Adapter (Item 2) using 4 Flat Head Screws (Item 6), 4 Flat
Washers (Item 4), and 4 Lock Nuts (Item 5) as shown in Figure 3.
.
Strong-Arm
Mount
(SAM)
(Item 3)
Screws
(Item 1)
Array Bracket
(Item 5)
Lock Nuts
(Item 4)
Flat
Washers
(Item 2)
360° Array Adapter
(Item 7)
Threaded Rod
Adapter
Threaded Rod Adapter Assembly
(Item 6)
Flat Head
Screws
Figure 3

Tripod Mounting (6.2/4.2 only)
Step 1: Assemble Array Brackets
(See Page 1.)
Step 2: Assemble SAM’s to Array Bracket
(See Page 2.)
Step 3: Assemble Pole Mount to 360
Array Adapter
Mount Pole Mount (Item 8) to the 360° Array
Adapter (Item 7) using 4 Flat Head Screws (Item
6), 4 Flat Washers (Item 4) and 4 Lock Nuts
(Item 5) as shown in Figure 4.
(Item 7)
360° Array Adapter
°
(Item 5)
Lock Nuts
(Item 4)
Flat
Washers
(Item 8)
Pole Mount
Figure 4
Pole Mount Assembly
(Item 6)
Flat Screws

3/8 Threaded Rod
Threaded Rod Suspension
This guide provides instruction on how to use EVID components to create example arrays. Correct use of this
hardware is required for secure array construction. Only persons with the knowledge of proper hardware and safe
suspension techniques should attempt to suspend any sound systems overhead. CAUTION! The weakest
component determines the size and safety of the entire array. Before suspending any array always inspect all
components of the array including building structural supports for cracks, deformations, corrosion or damage that
could reduce strength and safety of the array.
It is the responsibility of the user to ensure that any Electro-Voice loudspeaker system is suspended overhead in
accordance with all current federal, state, and local regulations.
© T elex Communications, Inc. 1 1/2001
Part Number 38110-062 Rev A
Pole Mount
Suspension Safety Warning
12000 Portland Avenue South, Burnsville, MN 55337
Phone:952/884-4051, Fax:952/884-0043
www.electrovoice.com