SMART THERMOMETER INSTRUCTION MANUAL
Congratulations on your purchase of the Williams-Sonoma
Smart Thermometer. In order to get started there are a few
things that you should do:
1. Your Smart Thermometer is designed to pair with the
iPhone, iPad, and iPod Touch devices using iOS5 or
above. It will not work with android phones or devices.
2. When first using the thermometer press the “on”
button on the rear of the unit and notice the level of
battery charge. It is best to plug the unit in using the
adaptor and allowing the unit to fully charge. The LCD
screen will show you when the unit is fully charged.
3. You should check your home router and make note of
the security settings. The settings are on the back of
your router and are either – WPA/WEP, WPA2 or NONE.
You will need to know this to set up your connection
with your Smart Thermometer.
4. Download the Williams-Sonoma Smart Thermometer
App to your iDevice.
of the screen and Manual will bring up a screen letting you set
your own temperature.
Connect the stainless steel probe to the Smart Therm and
once connect successfully the probe icon will show on the LCD.
Place the probe in the thickest part of the meat making
sure that it is not touching fat pockets or bone. The Smart
Therm will track the cooking process after the food reaches 90
degrees F and tell you when your food will be done.
Complete instructions for your Smart Thermometer are on the
Williams-Sonoma web site – www.williams-sonoma.com
Frequently Asked Questions:
How long will the battery last? - If fully charged the battery
should last 6 hours. The unit will work fully functionally until
the power is down to 20% at which time the wifi will not stay
connected.
The Smart Therm (WS Thermxxxx) is not showing up on my
iDevice in settings? - Reset your Smart Therm by using a pin
and gently push into the reset hole on the back of the unit.
Then completely shut down your Smart Therm by holding the
on/off button until the screen shuts off.
What is the range of the thermometer? - Normally the range
will be about 60meters (200 feet). There are many factors that
can change the range making it longer or shorter. In most cases
you should not have an issue with range in the home.
Can the unit be used without my iDevice? – Yes it can be used
as a stand along thermometer.
What happens if I am disconnected in the middle of cooking?
In many cases the unit will re-connect automatically. However
if it does not, close the app completely and re-open the app.
Most of the time this is caused by lost wifi connections and
your iDevice will remember the connection.
What is the maximum temperature that the unit will read? The unit will read up to 392F.
What if I see --- on the LCD? Usually this means that there is a
short in the wire or probe due to it being exposed to heat
above 750F or water has gotten into the wire. In this case the
probe and wire must be replaced.
How do I replace the probe and wire? You can request a
replacement by calling 1-800-526-0954 or Williams-Sonoma
customer service line. Replacement probes and wires are also
available at most Williams-Sonoma store locations.
the product has been tampered with. This product is not for
commercial use.
MADE IN CHINA
FCC Declaration of Conformity
This device has been tested and found to comply with the limits
for a Class B Digital Device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
device generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the
instructions, may cause harmful that interference will not occur
in a particular installation.
Any Changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority
to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
1) This device may not cause harmful interference
2) This device must accept any interference received,
including interference that may cause undesired operation.
This device complies with Part 15 of the FCC Rules and with
RSS-210 of Industry Canada. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
Changes or modifications to your device not expressly
approved by the party responsible for compliance can void the
user’s authority to operate the equipment.
RF Exposure Warning
The antennas used for this transmitter must be installed to
provide a separation distance of at least 20 cm from all persons
and must not be located or operating in conjunction with any
other antenna or transmitter.
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) This device may not cause interference, and
(2) This device must accept any interference, including interference that may cause undesired operation of the device.
Le présentappareilestconforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
L'exploitationestautorisée aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareildoit accepter tout brouillageradioélectriquesubi, mêmesi le
brouillageest susceptible d'encompromettre le fonctionnement.
RF Signal d'exposition
Les antennesutilisées pour cetransmetteurdoiventêtreinstallé
en considérantune distance de séparation de
toutepersonnesd’aumoins 20 cm et ne doivent pas
êtrelocaliséouutilisé en conflit avec tout
autreantenneoutransmetteur.
Loading...