Electronics Line 3000 EL2601-2 Users Manual

EL-2602

r

A

f

y

The EL-2602 is a universal transmitter designed for use with Electronics Line 3000’s supervised wireless range of receivers.
This transmitter includes a single input for use in a wide range of wireless applications.

Installation Instructions

1. To open the housing, insert a small screwdriver at the bottom of
the unit between the front and back cover and twist the
screwdriver to release the cover.

2. Remove the insulator separating the battery from the contacts on
the battery holder. When you apply power and the Tamper
switch is open, the EL-2602 enters Test mode during which a
transmission is sent every few seconds. You can terminate Test
mode by closing the Tamper switch. Test mode is automatically
terminated after approximately five minutes.

occurrence of voltage delay in lithium batteries that have been in
storage, the batteries may initially appear to be dead. In this case,
leave the unit in Test mode for a few minutes until the battery
voltage level is stabilized.

3. While the EL-2602 is in Test mode, set the receiver to
Registration mode and make sure that the EL-2602’s LED
lights up at least twice. After registration, momentarily close
the Tamper switch to terminate Test mode. Write the number
of the zone and the transmitter number (where applicable) on
the sticker provided. Affix the sticker inside the front cover for
future reference.

4. Before permanently mounting the unit, test the transmitter
from the exact mounting position. If necessary, relocate the
transmitter to a better position.

5. To remove the printed circuit board (PCB), press the PCB
release tab, carefully lift the board and slide it away from the
back cover.

pressure on the antenna.

Note: When handling the PCB, do not apply

Note: Due to the

6. Knockout the wiring hole in the back cover.

7. Thread the wires through the wiring hole.

8. Mount the back cover to the wall using two screws and replace the PCB. Use ISO
7050 (ST3.5 x 22) or similar countersunk screws so that the screw head will not
touch the PCB – see Figure 2.

9. Connect the terminal block as follows: 1 - Alarm; 2 - GND.

Note: The EL-2602 does not have EOL supervision of its loop wiring. Therefore, for
UL Household Burglary installations, the loop wiring may not exceed 3 feet.

10. Test the transmitter making certain that the LED is lit during transmissions.

11. Close the front cover of the EL-2602.

Technical Specifications

Antenna: Built-in Internal Whip
Frequency: 418MHz FM
Power: 3.6V ½ AA Lithium Battery (Part No. BT5055)

Caution: Fire, explosion and severe burn hazard!

Do not recharge, disassemble or heat above 212°F (100°C).

Current Consumption: 25mA (transmission), 10µA (standby)

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a r esidential installation. This equipment generates, uses and can radiate radio f requenc
energy and, if not installed and used in accordance with the instructions, may cause harmful interf erence to radio communications. However, there is no guar antee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the f ollowing measures:

1. Reorient or relocate the receiving antenna, 2. Increase the separation between the equipment and the receiver, 3. Connect the equipment into an outlet on a
circuit different from that to which the receiver is connec ted, 4. Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modifications to this equipment not expres sly approved by the party responsible for compliance (Electronics Line 3000 Ltd.) could void the
user’s authority to operate the equipment.

Antenna

LED

Indicato

Location
of wiring

knockout

Input Voltage Range: 0-15VDC/AC (peak to peak)
RFI Immunity: 40V/m
Operating Temperature: 32-140°F (0 to 60°C)
Dimensions: 2.6”H X 1.2”W X 1”D (65 x 30 x 25mm)

Figure 1: EL-2602 (Cover Off)

PCB

HOUSING

Figure 2: Mounting

Screw Position

FCC ID: RIYEL2601-2

Battery
Holder

Tamper
Switch

Terminal
Block

PCB
Release
Tab

Electronics Line 3000 Ltd.: 2 Granit Street, Kiryat Arieh, POB 3253, Petah Tikvah 49130 Israel. Tel: ( 972-3) 918-1333, Fax: [phone]

USA: 5637 Arapahoe Avenue, Boulder, Colorado 80303. Tel: [phone], Fax: [phone]

UK: Unit 7, Leviss Trading Estate, Station Road, Stechford, Birmingham B33 9AE. T el: (44-121) 789-8111, Fax: [phone]

France: ZI-61, rue du Marché Rollay, 94500 Champigny-Sur-Marne. Tel: [phone], Fax: [phone]

ll data is subject to change without prior notice. In no event shall Electronics Line 3000 Ltd. (EL3K) be liable for an am ount in excess of EL3K.’s original selling price o

this product, for any loss or damage whether direct, indirect, incidental, consequential or otherwise arising out of any failure of the product.

ZI0307A (10/03)