Electronics Line EL-2635, EL2635-P User guide
2
Figure 1: Typical Single Repeater
EL-2635 & EL2635P Repeater & Programming keypad – Repeater & Programierbedienteil – Repeteur & Clavier – Repeater & Keypad
Conrad No: 1276483 & 1276484
SAFETY WARNINGS
•
To prevent short circuits, this product should only be used inside and only in dry
spaces. Do not expose the components to rain or moisture. Do not use the product
close to a bath, swimming pool etc.
•
Do not expose the components of your systems to extremely high temperatures
or bright light sources.
•
In case of improper usage or if you have altered and repaired the product
yourself, all guarantees expire. Electronics Line does not accept responsibility in
the case of improper usage of the product or when the product is used for
purposes other than specified. Electronics Line does not accept responsibility for
additional damage other than covered by the legal product responsibility.
•
This product is not a toy. Keep out of reach of children.
•
The product should only be repaired or serviced by a qualified repairman.
•
Keep batteries out of the reach of children. Dispose of batteries as chemical
waste. Never use old and new batteries or different types of batteries together.
Remove the batteries when you are not using the system for a longer period of
time. Check the polarity (+/-) of the batteries when inserting them in the product.
Wrong positioning can cause an explosion.
•
Only connect the adapter to the mains after checking whether the mains voltage
is the same as the values on the identification tags. Never connect an adapter
when it is damaged. In that case, contact your supplier.
INTRODUCTION
The EL-2635 wireless repeater is a part of the Electronics Line Secuplace series,
and operates together with the Secuplace alarm system. When you wish to
know more about the complete system, its possibilities and its settings, then
you can check out the installation manual or visit www.electronics-line.com. Up to
four repeaters can be registered to the control panel with 32 transmitters
registered to each repeater. The repeater is powered by either 9VAC or
12VDC with a 6V rechargeable backup battery pack. Registration and
maintenance tests are performed using a plug-in LCD Programming Keypad
(EL2635-P) that provides a comprehensive interface to the repeater.
3
EL-2635 Repeater & Programming keypad – Repeater & Programierbedienteil – Repeteur & Clavier – Repeater & Keypad
Conrad No: 1276483 & 1276484
INSTALLATION
1.
Register all wireless devices to the Secuplace control panel as explained in
the Secuplace installation manual.
2.
On the control panel, define the detection devices that are intended to transmit
via the repeater as follows:
From the Programming menu, select Devices, Zones [911].
Select the zone you want to program (1-32).
From the zone’s sub-menu, select Repeater [#9].
Select “Use Repeater”.
Note: It is not necessary to define, at the control panel, the keypads and
keyfobs that are registered to the repeater.
3.
Open the EL-2635’s plastic housing. To do so, remove the two cover
screws and lift the front cover away from the base.
Antenna
Connector
Upper
Mounting
Hole
Transmitter
Receiver
Power Input
Terminals
AC Power
Protection Fuse
Lower
Mounting
Hole
Wiring
Hole
Figure 2: EL-2635 (cover
removed)
LED Indicator
Flash
Programming
Programming
Keypad (EL2635P)
Backup
Battery Pack
Battery Connector
Lower
Mounting
Hole
Tamper
Switch
4
EL-2635 Repeater & Programming keypad – Repeater & Programierbedienteil – Repeteur & Clavier – Repeater & Keypad
Conrad No: 1276483 & 1276484
4.
Connect the antenna provided to the antenna connector.
5.
Connect the backup battery pack to the Battery connector.
6.
Connect a 9VAC or 12VDC transformer to the Power Input terminal block
(polarity is not important).
7.
All registration and test functions, described in the following sections, are
performed from the LCD Programming Keypad (EL2635-P) shown in Figure
Loading...