Page 1
Issue 5.2014
EA DOGL128-6 GRAPHIC
128x64 DOTS, 3.3V
also available in low quantity !
flat: 6.5mm with LED B/L mounted
EA DOG
EA LED68x51-W
L128W-6 +
EA DOGL128B-6 +
EA LED68x51-W
EA DOG
EA LED68x51-A
L128W-6 +
TECHNICAL DATA
* HIGH-CONTRAST LCD SUPERTWIST DISPLAY (STN AND FSTN) WITH 15µm DOT GAP
* OPTIONAL LED BACKLIGHTS IN VARIOUS COLORS
* 128x64 PIXELS (CORRESPONDS TO 8x21 CHARACTERS OR 4x16 LARGE CHARACTERS)
* ST7565R CONTROLLER WITH SPI (4-WIRE) INTERFACE
* POWER SUPPLY: SINGLE SUPPLY 3.0V TO 3.3V (TYPICALLY 320µA)
* NO ADDITIONAL VOLTAGES REQUIRED
* OPERATING TEMPERATURE RANGE -20°C TO +70°C (STORAGE -30°C TO +80°C)
* LED BACKLIGHTING 5mA TO 90mA
* NO MOUNTING REQUIRED: SIMPLY SOLDER ONTO PCB
ORDERING CODE
GRAPHICS DISPLAY, 128x64, 68x51mm EA DOGL128x-6
x: W = white background (FSTN pos. transflective)
E = yellow/green background (STN pos. transmissive)
B = blue background (STN neg. transmissive)
S = black background (FSTN neg. transmissive)
L = yellow/green background (STN pos. reflective, cannot be backlit)
LED BACKLIGHT, WHITE EA LED68X51-W
LED BACKLIGHT, YELLOW/GREEN EA LED68X51-G
LED BACKLIGHT, BLUE EA LED68X51-B
LED BACKLIGHT, RED EA LED68X51-R
LED BACKLIGHT, AMBER EA LED68X51-A
LED BACKLIGHT, GREEN EA LED68X51-E
LED BACKLIGHT, FULL COLOR RGB EA LED68X51-RGB
ACCESSORIES
USB TEST BOARD FOR PC (WINDOWS 2000, XP, VISTA) EA 9780-2USB
TOUCH PANEL, 4-WIRE, ANALOG, STICK-ON EA TOUCH128-2
ZIF CONNECTOR FOR TOUCH PANEL, BOTTOM CONTACT EA WF100-04S
SOCKET CONNECTOR 4.8 mm HEIGHT (2 PCS. REQUIRED) EA FL-20P
CHARACTER SETS PLUS FONTEDITOR EA USBSTICK-FONT
Page 2
EA DOGL128-6 GRAPHIC
EA DOGL128-6
The EA DOGL128-6, a 128x64-pixel graphics display, is a new addition to ELECTRONIC ASSEMBLY’s EA DOGL
series. It, too, has pins that allow it to be mounted quickly and easily. 7 different optional LED backlights are
available. These can be combined with 5 different display technologies, making it possible to have up to around
20 different designs.
Designed for compact, handheld devices, this modern LCD series offers a number of benefits with and without
backlighting:
* Extremely compact (68x51 mm) with a large viewing area of 64x36 mm
* Super-flat: 2.8 mm without backlight module, and only 6.5 mm with a b./l. module mounted
* Serial SPI interface (4-wire)
* Single supply +3.0 V or +3.3 V or dual power supply +1.8..3.3V
* Typical power consumption of only 320µA in full operation (white LED backlight from 5mA)
* Easily mounted by soldering
* Wide range of design variants orderable as single units, backlighting color changes possible
CONTRAST ADJUSTMENT
The contrast can be set by means of a command for all the displays in the EA DOGL128-6 series. The contrast
setting of the display must be set once by the software, and is then kept constant throughout the entire operating
temperature range (-20..+70°C), thanks to the integrated temperature compensation.
LED BACKLIGHT
7 different variants are available for individual
backlighting: white, yellow/green, green, blue,
red, amber and a full-color version.
There are 3 separate LED paths available for
each monochrome backlight that can be
switched in parallel or in series to suit the
system voltage. This means that most
backlights can be run at either 3.3 V or a
higher voltage.
To operate the backlight, we recommend a
current source (e.g. CAT4238TD) or an
external series resistor to limit the current.
This can be calculated from R=U/I; you can
find the values in the table on the right. To
prolong the life of the backlights, we
recommend that you use a current source.
The operating life of the yellow/green, red and
LED backlight
yellow/green
EA LED68x51-G
white
EA LED68x51-W
amber
EA LED68x51-A
green
EA LED68x51-E
blue
EA LED68x51-B
red
EA LED68x51-R
full color
EA
LED68x51-RGB
Forward voltage (V)
min typ max @3,3 V @5 V
2,1 60 20 47
3,3 45
2,1 60 24 52
3,1 45
3,3 45
2 60 24 52
red green blue
typ. 4V typ. 4V typ. 4V
Current
max.
(mA)
60 each
colour
amber backlights is 100,000 hours. The life of the white and blue backlights is considerably shorter. We recommend
that you dim these or switch them off whenever possible.
Important: Never connect the backlight LEDs directly to a 5 V/3.3 V supply as this will immediately destroy
the LEDs. Always use a current source. Please note that derating applies at temperatures exceeding
+25°C.
Limiting resistor
(ohm, each
path)
CAT4238
CAT4238
CAT4238
-
39
33
39
15
ASSEMBLING
First, clip the display and backlight modules together by gently pushing the display pins through the corresponding
holes on the backlight module. Then insert the entire module into the socket, or into the soldering holes on the
pcb. The backlight pins (the 2 rows with 3 pins at the bottom) must be soldered on the top side as well to ensure
good contact between the modules.
Important: The display has 2 protective films on the top and the bottom (except the version EA DOGL128L
that does have 1 foil on the top only), and there is also one on the backlight. These must be removed.
Make sure that neither display nor backlight will never come into contact with any kind of liquid like
Fluxer, Cleaner, Water.
Page 2
ELECTRONIC ASSEMBLY reserves the right to change specifications without prior notice.
Printing and typographical errors reserved.
Page 3
EA DOGL128-6 GRAPHIC
5 DIFFERENT TECHNOLOGIES
See below for an overview of available technologies, combinations with available backlights and their usability:
display type technology
FSTN pos.
transflective
STN pos.
yellow/green
transmissive
STN neg. blue
transmissive
FSTN neg.
transmissive
optional
backlight
it's fine with and
without backlight
backli ght unit
required
usage only with
backlight
usage only with
backlight
readability
readable even
without
backlight
readable even
without
backlight
--- ---
--- ---
display color
non
backlighted
black on white
dark green on
yellow/green
display color
with
backlighted
black on backlight
color
black on
yellow/greenor
amber
backlight color on
blue b ackground
backlight color on
black background
recommended
backlight
color
white, blue, green,
RGB
yellow/green,
amber
white, yellow/green
white, green,RGB
STN pos.
yellow/green
reflective
no backli ght
possible
finestreadable
without
backlight
dark green on
yellow/green
--- ---
6 AND MORE DIFFERENT BACKLIGHTS
6 and more different backlight colors are available to match equipments design as much as possible. The
most effective and brightest one is the white one EA LED68x51-W.
EA LED68x51-W
White
If you see black and white pictures on this page but you want to see the colors
of the displays, you can download a full-colored version of this document at
http://www.lcd-module.de/eng/pdf/grafik/dogl128-6e.pdf
EA LED68x51-G
Yellow/green
EA LED68x51-B
Blue
EA LED68x51-R
Red
EA LED68x51-A
Amber
EA LED68x51-E
Green
EA LED68x51-RGB
Full Color
Printing and typographical errors reserved.
ELECTRONIC ASSEMBLY reserves the right to change specifications without prior notice.
Page 3
Page 4
APPLICATION EXAMPLES
+3.0V or +3.3V (single supply) operation
requires 9 external capacitors
EA DOGL128-6 GRAPHIC
LOW POWER
LOW VOLTAGE
If an external source of +10.5..+13.5V (does not have
to be stabilized) is available, the charge pump is not
needed and less external components are required.
Power supply voltage for display and logic may be
1.8..3.3V then.
ZIF CONNECTOR EA WF100-04S
As an accessory for the touch panel we do provide
a ZIF connector (4 pins) with pitch 1.0mm (SMD
type). This connector is a „bottom side contact“
type.
alle dimensions are in mm
SOCKET FOR THE DISPLAY
EA FL-20P provides a 20 pin socket which
matched perfect to the display. Note that 2 pcs.
per display are necessary.
Page 4
ELECTRONIC ASSEMBLY reserves the right to change specifications without prior notice.
Printing and typographical errors reserved.
Page 5
EA DOGL128-6 GRAPHIC
TABLE OF PROGRAMMING COMMANDS
DATA TRANSFER
Data transfer is unidirectional. That means that data can only be written; it cannot be read again. In contrast to
other displays, a busy query is not necessary with this display. The clock-pulse rate of the SCL line can be up
to 20 MHz at 3.3V, depending on the supply voltage. You will find more detailed information on timing on pages
64 and 65 of the data sheet of the ST7565R controller, which you will find on our website at
http://www.lcd-module.de/eng/pdf/zubehoer/st7565r.pdf
Printing and typographical errors reserved.
ELECTRONIC ASSEMBLY reserves the right to change specifications without prior notice.
Page 5
Page 6
EA DOGL128-6 GRAPHIC
INITIALISATION EXAMPLE „LOW POWER“
Using the internal contrast voltage generator (single supply +3.0..+3.3V).
Application „LOW POWER“.
Initialisation example for single supply +3.3V (bottom view)
C omma nd
(2) Display start line set 0 0 1 0 0 0 0 0 0 $40 Display start line 0
(8) ADC s et 0 1 0 1 0 0 0 0 1 $A1 ADC reverse *)
(15) Common output mode select 0 1 1 0 0 0 0 0 0 $C0 Normal COM0~COM63
(9) Display normal/reverse 0 1 0 1 0 0 1 1 0 $A6 Display normal
(11) LCD bias set 0 1 0 1 0 0 0 1 0 $A2 Set bias 1/9 (Duty 1/65)
(16) Power control set 0 0 0 1 0 1 1 1 1 $2F
(20) Booster ratio set
(17) V0 voltage regulator set
(18) Electronic volume mode set 0
(19) Static indicator set 0
(1) Display ON/OFF 0 1 0 1 0 1 1 1 1 $AF Display on
A0 D7 D6 D5 D4 D3 D2 D1 D0 He x
1 1 1 1 1 0 0 0 $F8
0
0 0 0 0 0 0 0 0 $00
0 0 0 1 0 0 1 1 1
1 0 0 0 0 0 0 1 $81
0 0 0 1 0 1 1 0 $10
1 0 1 0 1 1 0 0 $AC
0 0 0 0 0 0 0 0 $00
Remark
Booster, Regulator and Follower
on
Set internal Booster to 4x
$27
Contrast set
No indicator
*) Make sure that for 6:00 viewing direction ADC has to be set to „reverse“ (mirrored layout) !
INITIALISATION EXAMPLE „LOW VOLTAGE“
Using an external power supply for contrast voltage (dual power supply).
Application „LOW VOLTAGE“.
Initialisation example for dual power supply(bottom view)
C omma nd
(2) Display start line set 0 0 1 0 0 0 0 0 0 $40 Display start line 0
(8) ADC s et 0 1 0 1 0 0 0 0 1 $A1 ADC reverse *)
(15) Common output mode select 0 1 1 0 0 0 0 0 0 $C0 Normal COM0~COM63
(9) Display normal/reverse
(11) LCD bias set 0 1 0 1 0 0 0 1 0 $A2 Set bias 1/9 (Duty 1/65)
(16) Power control set 0 0 0 1 0 1 0 1 1 $2B
(17) V0 voltage regulator s et 0 0 0 1 0 0 1 1 1 $27
(18) Electronic volume mode set 0
(19) Static indicator set 0
(1) Display ON/OFF 0 1 0 1 0 1 1 1 1 $AF Display on
A0 D7 D6 D5 D4 D3 D2 D1 D0 He x
0 1 0 1 0 0 1 1 0
1 0 0 0 0 0 0 1 $81
0 0 0 1 0 1 1 0 $10
1 0 1 0 1 1 0 0 $AC
0 0 0 0 0 0 0 0 $00
$A6 Display normal
Remark
Booster off, Regulator, Follower
on
Contrast set
No indicator
Orientation for 6 o’clock
(Bottom View)
*) Make sure that for 6:00 viewing direction ADC has to be set to „reverse“ (mirrored layout) !
Page 6
ELECTRONIC ASSEMBLY reserves the right to change specifications without prior notice.
Printing and typographical errors reserved.
Page 7
EA DOGL128-6 GRAPHIC
Initialisation example top view
Comma nd
A0 D7 D6 D5 D4 D3 D2 D1 D0 Hex
Remar k
(8) ADC set 0 1 0 1 000 0 0 $A0 ADC normal
(15) Common output mode select 0 1 1 0 0 1 0 0 0 $C8 Reverse COM63~COM0
Specification
Specification min max Unit
Top-Bottom 100 400
Ω
Left-Right 110 410
Ω
Voltage 3 12 V
Current 5 25 mA
Linearity 1,5 %
Force 45 65 g
Contact
Bo unce
5 10 ms
Op.
Temperatur
-20 +60 °C
Stor.
Temperatur
-20 +70 °C
Transmission 75 85 %
Life Time 10000 Cycles
12:00 VIEWING ANGLE, TOP VIEW OPTION
If the display is read mostly from above (on the front of a laboratory power supply
unit, for example), the preferred angle of viewing can be set to 12 o’clock. This rotaties
the display by 180°. A slightly different initialization setup is
required for this. Also keep in mind that the leftmost column
(normally numbered as 0) will now change to 4.
Orientation for 12 o’clock
(Top V iew)
TOUCH PANEL EA TOUCH128-2 (OPTIONAL)
An analog touch panel is available as an accessory. It has a self-adhesive material on its rear surface and is
simply stuck onto the display. The connection is made by means of a 4-pin flexible cable for a ZIF connector (e.g.
EA WF100-04S) with a grid of 1.0 mm. Bending radius is defined
with min. 5mm. For optimum readability we recommend that you
use a backlight with the
display.
Interfacing to a processor can
be either done by an external
touch panel controller or with
a controller that is featured
with analogue input. The touch
panel is similar to a
potentiometer: connecting a
voltage of e.g. 3.3V to the pins
Top-Bottom
to read out a voltage on pin
Left
or
the Y-coordinate of the
pressed point. The Xcoordinate will result when the
voltage will be supplied to
Left-Right
and measurement is done at
Top
or
Bottom
The pinout of the connecting cable is shown in the drawing.
makes it possible
Right
which is linear to
.
USB-TEST BOARD EA 9780-2USB
For easy startup, a USB test board is available that can be connected to a PC. An USB cable and Windows
software is supplied with the product. This allows text and images (BMP) to
displayed directly on the connected display. You will find more information on
the test board in the EA 9780-2USB data sheet.
SIMULATION WITH WINDOWS
A simulator window also displays the contents of the display. The software can
simulate all the displays and colors even without the hardware. You can
download the software free from our website:
http://www.lcd-module.de/deu/disk/startdog.zip
Printing and typographical errors reserved.
ELECTRONIC ASSEMBLY reserves the right to change specifications without prior notice.
Page 7
Page 8
EA DOGL128-6 GRAPHIC
DIMENSIONS EA DOGL128-6
Pin Symbol Level Function Pin Symbol Level Function
1 NC (A1+: LED backlight) 21 V0 - LC Drive
2 NC (A2+: LED backlight) 22 V1 - LC Drive
3 NC (A3+: LED backlight) 23 V2 - LC Drive
4 24 V3 - LC Drive
5 25 V4 - LC Drive
6 26 VSS L Power Supply 0V (GND)
7 27 CAP2N - Voltage Converter
8 28 CAP2P - Voltage Converter
9 29 CAP1P - Voltage Converter
10 30 CAP1N - Voltage Converter
11 31 CAP3P - Voltage Converter
12 32 VOUT -
13 33 VSS L Power Supply 0V (GND)
14 34 VDD2 H Power Supply Booster
15 35 VDD H Power Supply +1.8..3,3V
16 36 SI H / L Serial Data In
17 37 SCL H / L Serial Clock
18 NC (C1-: LED backlight) 38 A0 H / L L= Command, H= Data
19 NC (C2-: LED backlight) 39 RST L Reset (active low)
20 NC (C3-: LED backlight) 40 CS1B L Chip Select (active low)
Voltage Output about
+12V
Technische Änderung vorbehalten.
Wir übernehmen keine Haftung für
Druckfehler und Applikationsbeispiele.
all dimensions are in mm
ATTENTION
handling precautions!
Note:
- LC displays are generally not suited for wave or
reflow soldering. Temperatures of over 80°C can
cause lasting damage.
- The surfaces of the displays and backlights are
protected from scratching by self-adhesive protective
foils. Please remove these before mounting.
- Make sure that either display nor backlight will never
come into contact with any kind of liquid like Fluxer,
Cleaner, Water.
DIMENSIONS EA LED68X51
ELECTRONIC ASSEMBLY GmbH
Zeppelinstraße 19
D-82205 Gilching
Germany
ATTENTION
handling precautions!
Note:
The 6(4) LED pins A1 to A3
and C1 to C3 also have to be
soldered from above to ensure
good contact.
all dimensions are in mm
Fon: +49 (0)8105-7780 90
Fax: +49 (0)8105-7780 99
e-Mail: info@lcd-module.de
Web: www.lcd-module.com
Loading...