Refrigerator
INSTRUCTION BOOKLET
818 21 42--01/1
ERC3709
GB
DK
Important Safety Instructions
Your new fridge may have other functions compared to your previous one.
These warnings are provided in the interests of your safety. Ensure that you understand them all before
installing or using the appliance. Your safety is of paramount importance. If you are unsure about any of the
meanings or warnings contact the Customer Care Department.
Keep the instruction booklet. It will come in handy if you later sell the appliance or give it to somebody else.
Prior to Installation
· Check the appliance for transport damage. Under
no circumstances should a damaged appliance be
installed. In the event of damage please contact
your retailer.
Installation
· This appliance is heavy. Care should be taken
when moving it.
· It is dangerous to alter the specifications or
attempt to modify this product in any way.
· Ensure that the appliance does not stand on the
electrical supply cable. If the supply cable is
damaged, it must be replaced by a cable
avaliable from your local Service Force Centre.
· Any electrical work required to install this
appliance should be carried out by a qualified
electrician or competent person.
· Parts which heat up should not be exposed.
Whenever possible, the back of the appliance
should be close to a wall, but leaving the
required distance for ventilation, as stated in the
installation instructions.
The appliance should be left for 2 hours after
installation before it is turned on, in order to
allow the refrigerant to settle.
Child Safety
· Do not allow children to tamper with the controls
or play with the product.
· There is a risk of suffocation! Keep packaging
material away from children.
the refrigerating system on the back of and inside
the cabinet. If the refrigerating system is
punctured, the cabinet will be damaged and
foodstuff inside may spoil.
If the refrigerant circuit should become
damaged:
avoid open flames and sources of ignition
thoroughly ventillate the room in which the
appliance is placed
The refrigerant isobutane (R600a) is contained
within the refrigerant circuit of the appliance, a
natural gas with a high level of environmental
compatibility, which is nevertheless flammable.
· Do not place carbonated or fizzy drinks in the
freezer compartment. Bottles and cans must not
be placed in the frezeer compartment as they can
burst when the contents freeze.
Maintenance and Cleaning
· Before cleaning, always switch off the apppliance
and disconnect from the electrical supply
· When unplugging always pull the plug from the
mains socket, do not pull on the cable
.
Servicing
· This product should be serviced by an
authorised engineer and only genuine spare
parts should be used.
· Under no circumstances should you attempt to
repair the appliance yourself. Repairs carried out
by inexperienced persons may cause injury or
serious malfunctioning. Contact your local
Service Force Centre.
During Use
· This appliance is designed for domestic use only,
specifically for the storage of edible foodstuffs.
It is not intended for commercial or industrial
use.
· Containers with flammable gases or liquids can
leak at low temperatures. Do not store any
containers with flammable materials, such as
spray cans, fire extinguisher refill cartridges etc.
in the refrigerator or freezer.
Do not let sharp objects come into contact with
At the end of the Appliance Life
· When disposing of your appliance use an
authorised disposal site.
· Remove the plug and ensure that any locks or
catches are removed, to prevent young children
being trapped inside.
Scrapping old cabinets
When discarding the cabinet, hand it over to a
recycling station. For m ore information, contact your
local Council or Environmental Health office.
Electrolux 818 21 42-01/1
2
Contents
Important Safety Instructions 2.......
Scrapping old cabinets 2.......................
Contents 3..........................
Description of the Appliance 4........
Control Panel 4..............................
Before use 4.........................
Using the fridge 5....................
To start the fridge and thermostat control 5........
Temperature inside the fridge 5.................
Measuring the temperature 5...................
Switching off 5..............................
Cabinet interior 6............................
Hints and Tips 6.....................
Energy Saving Advice 6.......................
Food Storage 6..............................
Normal Operating Sounds 7....................
Maintenance and Cleaning 7..........
Removing the ventilation grille 7................
Internal Cleaning 7...........................
External Cleaning 7..........................
Defrosting the fridge 7........................
To Change the Light Bulb 8....................
When the appliance is not in use 8...............
Something Not Working 8............
ServiceandSpareParts 9............
Customer Care Department 9...................
Guarantee Conditions 9..............
Standard Guarantee Conditions 9................
Technical specification 10.............
Installation 10........................
Mains Cable 10...............................
Unpacking 10................................
Removing the transport supports 10..............
Cleaning 10..................................
Installing the appliance 11......................
Electrical connection 12........................
Door Reversal 13.............................
Guide to use the instruction book
The following Symbols will be found in the text to guide you through the instructions
Safety instructions
1, 2, 3 ...
Step by step instructions for an operation
Hints and tips
Electrolux 818 21 42-01/1
3
Description of the Appliance
1
2
1
1
1
5
1
5
1
1
5
6
Control Panel
10
10
7
8
9
4
3
Model ERC3709
1. glass shelf
2. bottle shelf
3. bottle shelf
4. egg holder
5. vegetable drawer
6. ventilation grille
7. butter compartment
8. door shelf +box
9. sliding shelf
10. door shelf
AB
A. Green pilot light
Illuminates when the fridge is operating.
Before use
·Remove all securing tapes.
·Wash the inside of the appliance with lukewarm
water with a little bicarbonate of soda added (5ml to
0,5 litre of water). Do not use soap or detergent as
the smell may linger. Dry the appliance thoroughly.
Do not use detergents, abrasive powders,
highly perfumed cleaning products, wax,
polishes or products containing alcohol.
Check that the drain hose at the rear of the cabinet
discharges into the drip tray.
·Before inserting the power plug into the socket and
switching on the appliance for the first time, leave it
standing upright for about 30 minutes, or for 2 hours
if it was transported horizontally. Otherwise the compressor may sustain damage. This time will allow the
oil sufficient time to return to the compressor.
B. Thermostat control knob
Usetoswitchonandsetthedesiredtemperaturein
the fridge.
GB
Electrolux 818 21 42-01/1
4
Using the fridge
To start the fridge and thermostat
control
Turn the thermostat control knob to the desired
position.
MIN The lowest position of the thermostat control
results in the highest temperature inside the cabinet.
MAX The highest position of the thermostat control
results in the lowest temperature inside the cabinet.
H : Switched off.
Allow the appliance to run for a period of 24 hours
whenever the temperature setting is changed. This
will allow the temperature to stabilise inside the
appliance.
Temperature inside the fridge
A suitable temperature inside the fridge is approx.
+5°C. If the thermostat control is set too cold, food
with a high water content may start to freeze if it has
been placed in the coldest places in the fridge.
(+ warm, - cold)
Meat, fish and milk should be put in the coldest part
of the cabinet.
The temperature will be affected by:
· How often the door is opened
· How much food is stored
· Position of the appliance (See the Installation
section.)
+
+
--
--
--
--
+
+
+
+
+
+
Measuring the temperature
If the temperature is measured using a standard,
single thermometer, this should be put in a glass of
water centrally placed inside the appliance. This will
reflect the temperature inside the food products. Do
not place the thermometer hanging or lying directly
on the shelf.
· Distribute foodstuffs to allow cold air to
circulate freely between the products.
· Do not place food products directly against the
cooling plate on the rear wall as they may
freeze here.
· Also never put warm products into the appliance.
Wait until they have cooled down.
· Cover all foods properly to avoid odours and
flavours from tainting other food.
Switching off
Turn the control anti-clockwise past the click
position to "H".
Remove the power supply plug from the wall socket.
Electrolux 818 21 42-01/1
5
Cabinet interior
The shelves and door compartments are removable
and can easily be re-arranged.
Certain shelves must be lifted up by the rear edge to
enable them to be removed.
The lower door compartment and the glass shelf
above the salad drawer must not be moved. They are
required for proper air circulation inside the cabinet.
Shelves with a raised edge should be placed with the
raised edge facing the rear wall of the cabinet, and
thus prevent food products from touching the
cooling plate.
The vegetable box has two moveable partitions with
five different choices in order to separate different
vegetables.
The vegetable box has a ventilation edging to
increase the circulation of air and reduce the risk of
condensation.
Hanging h alf-shelf
The half-shelf can be moved sideways. It can be
hung under all door shelves, except the lowest one.
Hints and Tips
Energy Saving Advice
· Do not install the cabinet close to sources of heat
such as a cooker, dishwasher or radiator.
· Locate the appliance in a cool well ventilated
room and make sure that the air openings of the
cabinet are not obstructed.
· Always leave warm food to cool down to room
temperature before placing in the fridge.
· Try to avoid keeping the door open for long
periods, or opening the door too frequently as
warm air will enter the cabinet, and cause the
compressor to switch on unnecessarily often.
· Ensure there are no obstructions preventing the
door from closing properly.
· It is advisable to periodically clean the
refrigeration system at the back of the appliance
with a duster or vacuum cleaner.
· Always leave warm food to cool downn to room
temperature before placing in the fridge.
· Make sure the door gasket is complete and
always clean.
Food Storage
· To obtain the best results from your appliance,
neither hot foods nor liquids which may
evaporate, should be placed in the larder
compartment.
· Keep the time between buying chilled food and
placing it in your fridge as short as possible.
· Do not push food together too much, try to allow
air to circulate around each item.
· Do not store food uncovered.
Remove suspect food from you refrigerator and
clean, refer to cleaning and maintenance.
Electrolux 818 21 42-01/1
6
Normal Operating Sounds
· You may hear faint gurgling or bubbling sounds
when the refrigerant is pumped through the coils
or tubing at the rear, to the cooling
plate/evaporator.
being pumped round, and you will hear a
whirring sound or pulsating noise from the
compressor.
· A thermostat controls the compressor and you
will hear a faint " click" when the termostat cuts
in and out.
· When the compressor is on, the refrigerant is
Maintenance and Cleaning
Removing the ventilation grille
The ventilation grille can be removed, e.g. to wash
the grille.
Make sure the door is open when removing the
ventilation grille. Unsnap the upper edge of the grille
by pulling outward/downward. Then pull the grille
straight out to completely remove it.
Internal Cleaning
Clean the inside and the accessories with warm
water and bicarbonate of soda (5 ml to 0,5 litre of
water).
Rinse and dry thoroughly.
Do not use detergents, abrasive
powders, high perfumed cleaning
products, wax polishes or cleaning
products containing bleach or alcohol .
Regulary check the door seals and wipe clean to
ensure they are clean and free from debris.
Clean out the drip channel inside the fridge at
regular intervals and ensure that the drip channel is
clear at all times. If blocked carefully clear using a
piece of flexible curtain wire inserted into the drain
outlet to remove the blockage.
External Cleaning
Disconnect the appliance from electricity supply.
Wash the outer cabinet with warm soapy water.
Remove the ventilation grille (see the section
"Removing the ventilation grille") and vacuum-clean
under the cabinet. Once or twice a year dust the
condenser (black grille) and the compressor at the
back of the appliance, with a brush or vacuum
cleaner, as an accumulation of dust will affect the
performance of the appliance and cause excessive
electricity consumption.
When moving the cabinet, lift it by
the front edge to avoid scratching
the floor.
Defrosting the fridge
The fridge is defrosted automatically every time the
compressor stops. Frost formation can be prevented
by:
· not putting warm foodstuff inside the cabinet.
· avoiding frequently opening the door or keeping
it open too long.
· not placing foodstuffs directly against the cold
cooling plate.
Electrolux 818 21 42-01/1
7
To change the light bulb
The light is switched on automatically when the
door is opened. Before replacing the light bulb,
disconnect the power plug from the outlet.
Press the spring together and pull the grille
downward at the same time.
Use a bulb of the same type, E14 socket, maximum
ratingof25W.
When the appliance is not in use
Disconnect the appliance from electricity supply.
Empty all foods and clean the appliance, leaving the
doors ajar to prevent unpleasant smells.
If the appliance is left on, e.g. while on holiday, ask
somebody to check it once in a while to prevent the
food inside from spoiling in case of a power failure.
Something Not Working
Before contacting your local Service Force Centre check the following points:
Symptom Solution
The temperature is too high inside the
refrigerator.
It is too cold inside the refrigerator. Set a warmer temperature.
There is water on the cooling plate inside
the refrigerator.
Water is running inside the refrigerator. Clean the water drain and drain hole inside the refrigerator
Water comes out on the floor. Place the drain hose at the back of the appliance above the
The compressor operates continuously. Set a warmer temperature.
Set a lower temperature.
Put food products in the right place inside the refrigerator. See
the chapter "Temperature inside the refrigerator".
Distribute the food products to allow cold air to circulate
around them.
Make sure that the door is completely closed and that the
rubber door seal is complete and clean.
The temperature where the cabinet is placed is not within its
operating limits. See installation section.
See the section"To start the fridge and thermostat control".
This is normal. During automatic defrosting, frost thaws on the
cooling plate.
using a piece of flexible curtain wire.
Food products could have been placed near the rear of the
appliance, preventing the water from running into the drain.
drain bowl. See the chapter "Before use"
Make sure that the door is completely closed and that the
rubber door seal is complete and clean.
The temperature where the cabinet is placed is not within its
operating limits. See installation section.
The cabinet does not operate at all.
Cooling or interior light does not
operate. No indicator lamps light.
The appliance is not switched on.
Power does not reach the appliance. (Try connecting another
electrical device to the power outlet.)
The fuse has blown.
The power plug is not properly connected.
Electrolux 818 21 42-01/1
8
Noise The refrigerating system will always produce some sounds. A
pulsing sound is heard when coolant is pumped inside the
cooling pipes. A ticking sound from the thermostat can be
heard when the compressor switches on and off. The sound
level varies depending on the operation of the cabinet.
If you feel the sound level is incorrect:
If the cushion spacers (between the cabinet wall and pipes)
come loose, put them back in place again.
Carefully follow t he instructions in the chapter "Installing the
cabinet".
Service and Spare Parts
In the event of your appliance requiring service, or if you wish to purchase spare parts please contact your
local Service Force Centre by telephoning:
08705 929929
Your tephone call be automatically routed the Service Force Centre covering your post code area.
For the address of your local Service Force Centre and further information about Service Force, please visit the
website at www.serviceforce.co.uk
Before calling out an engineer, please ensure you have read the details under the heading "Something Not
Working".
When you contact the Service Forse Centre you will need to give the following details:
1. Your name, address and post code
2. Your telephone number
3. Clear and concise details of the fault
4. The model and serial number of the appliance (found on the rating plate)
5. The purchase date.......................................................
Please note that a valid purchase receipt or guarantee documentation is required for in-guarantee
service calls.
Customer Care Department
For general enquiries concerning your Electrolux appliance or further information on Electrolux products, you
are invited to contact our Customer Care Department by letter or phone as follows or visit our website at
www .electrolux.co.uk
Customer Care Department
Electrolux
55-77 High Street
Slough
Berkshire
SL1 1DZ
Tel: 08705 950950*
* calls to this number may be recorded for training purposes.
Guarantee Conditions
Standard Guarantee Conditions
See Guarantee C onditions on the Registration Card.
Electrolux 818 21 42-01/1
9
Technical Specification
Model ERC3709
Gross volume 370 l
Width 595 mm
Height 1800 mm
Depth 600 mm
Energy consumption 179 kWh/year
Energy class A
Rated power 110 W
Installation
Mains Cable
In the event of damage to the appliance's main cable,
to avoid risks only an authorised service company
recommended by the supplier or a qualified person
may adjust it.
Unpacking
Unpack the appliance and check that it is in good
condition and free of any transport damage. Notify
the dealer immediately of any damage. Hand the
packaging over for recycling.
Do not allow children to play with the
packaging. The plastic film can cause
suffocation.
Removing the transport supports
Remove the tape and the transport supports from
· the door sides
· the shelves
Remove the transport support on the glass shelf by
pushing the support forward along the edge of the
shelf until it stops. Take hold of the rear edge of the
glass shelf and pull the shelf and transport support
forward until the shelf tilts and the transport support
can be removed. Some models are fitted with a
silencing pad under the cabinet. Do not remove this
pad.
Cleaning
Wash the inside of the appliance using lukewarm
water and bicarbonate of soda (5 ml to 0,5 litre of
water).
Do not use soap or detergent as the smell may
linger. Dry thoroughly.
10
Electrolux 818 21 42-01/1
Installing the appliance
When two appliances are placed beside each other,
the spacers enclosed in the plastic wrapping should
be glued between the appliances. As shown in the
illustration.
To obtain the best performance from the appliance,
ensure :
· the appliance is placed in a dry, cool place and
is not exposed to direct sunlight.
· the appliance is not placed close to a source of
heat, e.g. a cooker or dishwasher.
· the appliance is level. The appliance should not
lean
against any wall. If necessary adjust the
feet using the adjustment spanner supplied.
· there is good air circulation around the appliance
and that the air channels below and behind
the appliance are not blocked. The ventilation
space above the appliance must be at least 4 cm.
The ventilation space can either be
a) directly above the appliance, or
b) behind and above the top cupboard. In this case,
the space behind the cupboard must be at least
50 mm deep.
The appliance must be placed at a location whose
ambient temperature corresponds to the climate
classification*, for which the appliance is designed.
* See on the rating plate on the inside of the
appliance.
The following table shows which ambient
temperature is correct for each climate classification.
Climate
classification
SN
for an ambient temperature of
+10°C to +32°C
a)
b)
50mm
N
ST
T
+16°C to +32°C
+18°C to +38°C
+18°C to +43°C
·Check that the drain hose at the rear of the cabinet
discharges into the drip tray.
If the appliance is placed in a corner and the side
with the hinges facing the wall, the distance between
the wall and the appliance must be at least 230 mm
to allow the door to open enough so that the shelves
can be removed.
The power plug must be accessible after installation
of the appliance.
11
Electrolux 818 21 42-01/1
Electrical connection
Any electrical work required to install this
appliance should be carried out by a
qualified electrician or competent person.
This appliance must be earthed.
The manufacturer declines any liability should
these safety measures not be observed.
Electrical Requirements
Before switching on, make sure the electricity
supply voltage is the same as that indicated on the
appliance rating plate.
The appliance is supplied with a 13amp plug fitted.
In the event of having to change the fuse in the plug
supplied, a 13amp ASTA approved (BS1362) fuse
must be used.
Should the plug need to be replaced for any reason.
The wires in the mains lead are coloured in
accordance with the following code:
Green and yellow -Earth
Blue -Neutral
Brown -Live
The wire coloured green and yellow must be
connected to the terminal marked with the letter "E"
or by the earth symbol
yellow.
The wire coloured blue must be connected to the
terminal marked "N" or coloured black
The wire coloured brown must be connected to the
terminal marked "L" or coloured red.
Upon completion there must be no cut, or stray
strands of wire present and the cord clamp must be
secure over the outer sheath.
or coloured green and
12
Electrolux 818 21 42-01/1
Door Reversal
1. Close the appliance and disconnect the appliance
from the electricity socket.
2. Remove the ventilation grille. There is a part on
the grille that can be removed. Remove and
reposition it on the opposite side.
3. Support t he appliance on a wooden block when it
is laid down. This will make it easier to grip under
the appliance when returning to an upright position.
1
2
3
4. On the upper part of the appliance. Remove the
hinge pin and replace on the other side.
5. On the lower part of the appliance.
a. Unscrew the hinge.
b. Remove the door-closing fittings from the hinge
and put the hinge pin on the other side. Then attach
the supplied door-closing fitting.
6. a. Remove the door-closing fitting from the
bottom of the door.
b. Remove the plastic plug from the corresponding
hole on the other side. Use a screwdriver to lever the
plug loose. Then secure the supplied door-closing
fitting.
c. Secure the lower hinge.
7. Raise the appliance and replace the ventilation
grille.
8. To transfer the handle.
Unscrew the screws. Push the blanking plugs into
the holes on the opposite side of the door. Fit the
handle onto the opposite side by turning it one half
circle. Press the supplied plastic plugs into the holes
to which the handle was previously fitted.
4
5b
5a
6
a
b
c
9. Put the appliance in position. Check that the
appliance is level. See the section "Positioning the
appliance".
Electrolux 818 21 42-01/1
13
14
Electrolux 818 21 42-01/1
15
Electrolux 818 21 42-01/1
© Electrolux plc 2003
qЬЙ=bдЙЕнкздмс=dкзмй=бл=нЬЙ=пзкдЗDл=д~кЦЙлн=йкзЗмЕЙк=зС=йзпЙкЙЗ=~ййдб~еЕЙл=Сзк=вбнЕЬЙеI=ЕдЙ~ебеЦ=~еЗ=змнЗззк=млЙK
jзкЙ=нЬ~е=RR=гбддбзе=bдЙЕнкздмс=dкзмй=йкзЗмЕнл=EлмЕЬ=~л=кЙСкбЦЙк~нзклI=ЕззвЙклI=п~лЬбеЦ=г~ЕЬбеЙлI=о~Еммг=ЕдЙ~еЙклI
ЕЬ~бе=л~пл=~еЗ=д~пе=гзпЙклF=~кЙ=лздЗ=Й~ЕЬ=уЙ~к=нз=~=о~дмЙ=зС=~ййкзсK=rpa=NQ=Дбддбзе=бе=гзкЙ=нЬ~е=NRM=ЕзменкбЙл
~кзмеЗ=нЬЙ=пзкдЗK
MARIESTAD DT-AV
Loading...