Electrolux STM3900, STM4200, SBM3800, SBM4300 User Manual
IK007 integration kit installation manual
refrigeration
STM3900, STM4200,
SBM3800, SBM4300,
WTM2800, WTM3000, WTM3300, WTM3900, WTM4200, WTM4400, WTM5200,
WTE4200, WTE5200,
WBM3700, WBM3800, WBM4000, WBM4300, WBM5100,
WBE4300, WBE5100,
WRM3700, WRM4300,
WFM3000, WFM3600,
KTM3600, KTM3900, KTM4200, KTM4400, KTM5200,
KBM3800, KBM4300, KBM5100.
2 contents refrigeration integration kit
ContentsCongratulations
Congratulations and thank you for choosing our integration
kit. Before you install the integration kit, we recommend that
you read through the entire installation manual.
To avoid the risks that are always present when you install
an electrical appliance, it is important that the integration kit
and appliance is installed correctly. Please read the safety
instructions in this installation manual as well as the appliance’s
user manual to carefully to avoid misuse and hazards.
We recommend that you keep this instruction booklet
for future reference and pass it on to any future owners.
After unpacking the integration kit please check it is not
damaged. If in doubt, do not use the integration kit but
contact your local Electrolux Customer Care Centre.
• General warnings 3
• Refrigerator integration kit items 4
• Cupboard dimensions 5
• Installation of 120˚ hinge 8
• Preparation 9
• Attaching top hinge bracket 9
• Attaching slide-housing to refrigerator doors 10
• Placing refrigerator in cupboard 12
• Refrigerator alignment 12
• Securing refrigerator in cupboard 13
• Attaching slide-bar to cupboard door 14
before you call
Please ensure you read the installation manual fully
before you call for service, or a full service fee could
be applicable.
environmental tip
Information on disposal for users
• Most of the packing materials are recyclable. Please dispose
of those materials through your local recycling depot or by
placing them in appropriate collection containers.
• If you wish to discard this product, please contact your
local authorities and ask for the correct method of disposal.
General warnings
Please read the installation manual carefully and store in a
handy place for later reference. Pass the installation manual
on to possible new owners of the refrigerator. Please refer to
the fridge user manual for warnings relating to the appliance.
The symbols you will see in this booklet have these meanings:
tips and information
This symbol indicates tips and information about use
of the refrigerator
environmental tip
This symbol indicates tips and information about
economical and ecological use of the refrigerator
NOTE: We strongly recommend that a professional
builder/cabinetmaker builds this unit into required
cabinetry prior to finished installation in customer’s
kitchen. Electrolux can not take responsibility for
any installation issues when customer retrofits this
product into cabinetry. Cabinet door height built in
excess of refrigerator door height will be unsupported
and risk bowing.
refrigeration integration kit general warnings 3
NOTE: Please refer to your Appliance User Manual for
warnings relating to the appliance.
4 kit items refrigeration integration kit
120° hinge
120° hinge
mounting plate
120° hinge
mounting plate
120° hinge
mounting plate
120° hinge
mounting plate
Refrigerator integration kit items
Because this kit is common to a variety of models, you need
to select the items required to suit your model. The items
required for the models covered in this instruction booklet
are shown below.
Those items not required on your particular model should
be discarded.
item quantity in kit quantity required description
two door model single door model
Top Hinge Bracket
PNº 1433129
Slide-Housing
PNº 1445132
Slide-Bar
PNº 1421620
Location Bracket
Front Footing
PNº 1444993
Refrigerator Screws
PNº 741249
Cupboard Screws
PNº 1449422
1 1 1
2 2 1
2 2 1
1 1 1
8 8 4
12 12 8
120º Hinge
PNº 1457832
Mounting plate for hinge
PNº 1458211
Self tapping wood screws
PNº 1458212
5 5 (3+2) 3
5 5 (3+2) 3
20 20 12
NOTE: For the single door models WRM4300, WRM3700,
WFM3600 & WFM3000 an additional kit, part number 1449661
is required (see page 11 for details).
Cupboard dimensions
tips and information
Pages 5, 6, 7 and 8 should be given to the person
responsible for cupboard design and construction.
The cupboard dimensions required for each model are
shown on page 6,7 & 8.
NOTE:
1. All sizes are internal and measured in millimetres.
2. It is important to ensure that the correct cupboard
sizes are used to ensure adequate air flow around
the refrigerator.
3. Cupboard hinges should be a 120° opening type.
(Use hinges supplied).
4. Three hinges should be used on each cupboard
door higher than 1000mm.
5. Ensure the refrigerator is not connected to a power
supply whilst installation takes place.
6. Each operation should be carried out in the sequence
specified in this instruction sheet.
refrigeration integration kit cupboard dimensions 5
NOTE: All sizes are internal and in millimetres.
Model
(capacity litres)
2 door top freezer models Please
280 litre
290 litre
300 litre
330 litre
360 litre
390 litre
420 litre
440 litre
520 litre
2 door bottom freezer models
370 litre
380 litre
400 litre
430 litre
510 litre
single door models
300 litre
360 litre
370 litre
430 litre
Dim ‘A’
(mm)
minimum
1640
1640
1710
1810
1730
1810
1730
1810
1810
1660
1810
1760
1810
1810
1810
1810
1810
1810
Dim ‘B’
(mm)
680
680
680
680
680
680
740
740
740
740
680
740
740
740
680
680
680
680
Dim ‘C’
(mm)
700
700
700
700
795
795
795
795
895
745
795
745
795
895
700
795
700
795
Dim ‘D’*
(mm)
1047
1047
1117
1217
1137
1217
1137
1217
1217
702
702
702
702
702
–
–
–
–
Dim ‘E’
(mm)
500
500
500
500
600
600
600
600
600
600
600
600
600
600
500
600
500
600
Dim ‘G’
(mm)
219
219
219
219
241
241
241
241
278
241
241
241
278
219
241
219
241
Dim ‘H’
(mm)
300
300
300
300
395
395
395
395
495
395
395
395
395
495
300
395
300
395
use the
calculation
below to
measure
Dimension
‘I’ for your
specic
model.
Dim ‘I’*
(mm)
Step 1
Measure and conrm Dimension ‘A’.
Step 2
To calculate Dimension ‘I’ use the equation below.
Dim ‘I’ = Dim ‘A’ - (Dim ‘D’ + 5mm) mm
Step 3
* Add cabinetry thickness to Dimension ‘D’ and
Dimension ‘I’ for nal measurement before construction.
Loading...