Electrolux SATF7000FS1 Installation Guide
Installation instructions
Instrucciones e Instalaci6n
P/N 137195800A (0906)
Table of Contents
{mportant Safety {nstructions ................................................ 2 {nsta{{ation {nstructions ................................................... 9-10
Pre-{nsta{{ation Requirements ................................................ 2 Accessories/Rep{acement Parts............................................ 11
{nsta{{ation Requirements .................................................. 3-4 Notes.................................................................................. 12
{nsta{{edWasher Dimensions ............................................. 5-6 Espa_o{............................................................................... 13
Unpacking Washer ............................................................ 7-8
Important Safety Instructions
Foryour safety the information in this manual must be followed to minimize the risk of fire or explosion or to
prevent property damage, personal injury or loss of life. Do not store or use gasoline or other flammable vapors and liquids in
the vicinity of this or any other appliance.
Recognize safety symbols, words and labels
Safety items throughout this manua{ are labe{ed with a
WARNING or CAUTION based on the risk type as described:
This symbol alerts you to situations that
may cause serious body harm, death or
property damage.
This symbol alerts you to situations that may
cause bodily injury or property damage.
Read all of the following instructions before installing and using this appliance:
• Destroy the carton and plastic bags after the washer is unpacked. Children might use them for play. Cartons covered with
rugs, bedspreads, or plastic sheets can become airtight chambers causing suffocation. Placeall materials in a garbage con-
tainer or make materials inaccessible to children.
The electrical service to the washer must conform with local codes and ordinances and the latest edition of the National
Electrical Code, ANSI/NFPA70, or in Canada, CSA 22.1 Canadian Electrical Code Part 1.
Toavoid back or other injury, have more than one person move or lift the washer.
The instructions in this manual and all other literature included with this washer are not meant to cover every possible condi-
tion and situation that may occur. Good safe practice and caution MUST be applied when installing, operating and main-
taining any appliance.
Save these instructions for future reference.
Pre-lnstallation Requirements
Tools and materia{s needed for insta{{ation:
OR OR
Adjustable 3/8"or 10 mm Ratchet and
wrench box wrench socket set
AND
Adjustable
pliers
AND
Carpenter's level
Installation Requirements
Electrical system requirements
CIRCUIT- Individual, properly polarized and grounded 15
amp. branch circuit fused with 15 amp. time delay fuse or
circuit breaker.
POWERSUPPLY- 2-wire, with ground, 120 volt single phase,
60 Hz, Alternating Current.
Because of potentially inconsistent voltage capabili-
ties, the use of this washer with power created by gas pow-
ered generators, solar powered generators, wind powered
generators or any other generator other than the local utility
company is not recommended.
OUTLETRECEPTACLE- Properly grounded 3-prong receptacle
to be located so the power supply cord is accessible when
the washer is in an installed position.
Grounding requirements
Groundin
Do not, under
any circumstances,
cut, remove,
or bypass the
grounding prong,
Powercord with
3-prong grounded plug
_i:_'__i_ GF{(Ground Fault Interrupter) receptacle is not re-
quired.
- ELECTRICAL SHOCK HAZARD - {mproper
connection of the equipment grounding conductor can result
in a risk of electrical shock. Check with a licensed electrician
if you are in doubt asto whether the appliance isproperly
grounded.
1. The washer MUST be grounded. In the event of
malfunction or breakdown, grounding will reduce the
risk of electrical shock by a path of least resistance for
electrical current.
2. Since your washer is equipped with a power supply
cord having an equipment-grounding conductor and
Water supply requirements
Hot and cold water faucets MUST be installed within 42
inches (107 cm) of your washer's water inlet. The faucets
MUST be 3/4 inch (1.9 cm) with threading for laundry hose
connection. Water pressure MUST be between 30 and 120
psi. Pressuredifference between hot and cold cannot be more
than 10 psi. Your water department can advise you of your
water pressure.
a grounding plug, the plug MUST be plugged into an
appropriate, copper wired receptacle that isproperly
installed and grounded in accordance with all local codes
and ordinances or in the absence of local codes, with the
National Electrical Codes, ANSI/NFPA70 (latest edition).
If in doubt, call a licensed electrician. DO NOT cut off or
alter the grounding prong on the power supply cord. In
situations where a two-slot receptacle is present, it isthe
owner's responsibility to have a licensed electrician replace
it with a properly grounded three prong grounding type
receptacle.
96"
(244cm)
max.
Drain system requirements
1. Drain capable of eliminating 17 gais (64.3 L) per minute.
2. A standpipe diameter of 1-1/4 in. (3.18 cm) minimum.
3. The standpipe height above the floor should be:
Minimum height: 24 in. (61 cm)
Maximum height: 96 in. (244 cm)
.......... Drain hose attached to the washer can reach a 74 in.
(188 cm) high standpipe. For higher standpipe, use hose P/N
137098000, available from an authorized parts distributor.
Clearance requirements
DO NOT INSTALL YOUR WASHER:
1. In an area exposed to dripping water or outside weather
conditions. The ambient temperature should never be be-
low 60 ° F(15.6 ° C) to maximize detergent effectiveness
2. In an area (garage or garage-type building) where gaso-
line or other flammables (including automobiles) are kept
or stored.
3. On carpet. Floor MUST be solid with a maximum slope
of 1 inch (2.54 cm). To minimize vibration or movement,
reinforcement of the floor may be necessary.
Installation in a Recess or Closet
If washer and dryer are installed in the same closet, door
ventilation isrequired: A minimum of 120 square inches
(774.2 cm2) of opening, equally divided at the top and
bottom of the door, isrequired. Louvered openings should
be located 3 inches (7.6 cm) from bottom and top of door.
Air openings are required to be unobstructed when a door
is installed. A Iouvered door with equivalent air openings for
the full length of the door is acceptable.
MINIMUM INSTALLATIONCLEARANCES- Inches (cm)
SIDES REAR TOP FRONT
Alcove 0" (0 cm) 0" (0 cm) 0" (0 cm) n/a
Under-
Counter
0" (0 cm) 0" (0 cm) 0" (0 cm) 1" (2.5 cm)
Closet 0" (0 cm) 0" (0 cm) 16" (40.5 cm) 1" (2.5 cm)
Ii
II
10
0" ====ll_-i i_=lF-===
(Ocm)
[
" " O" _
(0cm)
/
closet door
f
60 sq. in.
(387.1 cm 2}
______
f
60 sq. in.
(387.1cm 2)
1" _""_01 _l==m"
(2.5cm) I I
It
It
II
f_
--i --i --
(Ocm) al
[ J
ii
ii
II
Installed Washer Dimensions
50.8" (129cm)
to clear open door _,_--
29.75"(75.5cm)*
to front of closed door
water supply
connection
on rear of unit _
_'_ 27.0" --
(68.5cm)
drain hose
on rear
of uniP
l
36.0"
(9t.5cm)
freestand washer
on _oor
floorline
washer mounted on
optional pedestal
floorline
To obtain these minimal depth dimensions, dryer must be vented straight back. Using a quick-turn 90 ° elbow (right or down on freestanding dryer) adds approximately 0.75 in. (2.0 cm)
to installation depth. Upward venting of exhaust on pedestal-mounted or freestanding dryer adds approximately 4 in. (10.2 cm) to installation depth. Leftward venting on
pedestaFmounted or freestanding dryer adds approximately 3.75 in. (9.5 cm) to installation depth. Downward venting of exhaust on pedestaFmounted dryer adds approximately
2.25 in. (5.7 cm) to installation depth.
_Hot and cold inlet hose length approximately 43 inches (109cm)
2Powersupply cord length approximately 60 inches (t52.5cm).
3Drain hose length approximately 52 inches (132cm).
50.8" (129cm)
to clear open door
29.75" (75.5cm)*
to front of closed door
r--
27.0'
(68,5cm)
!
51.25"
(130cm)
71.5"
(t82cm)
water supply
connection
on rear of unit _
gas supply
pipe on rear
of gas unit
37"
(94cm)
* To obtain these minimal depth dimensions, dryer must be vented straight back. Using a quick-turn 90° elbow (right) adds approximately 0.75 in. (2 cm) to installation depth.
Upward venting of exhaust on stacked dryer adds approximately 4 in. (10.2 cm) to installation depth. Downward venting of exhaust on stacked dryer adds approximately
2.25 in. (6.5 cm) to installation depth. Leftward venting of exhaust on stacked dryer adds approximately 3.75 in. (9.5 cm) to installation depth.
_Hot and cold inlet hose length approximately 43 inches (109cm)
2Powersupply cord length approximately 60 inches (152.5cm).
3Drain hose length approximately 52 inches (132cm).
power cord
on rear of unit 2
electrical
supply on
rear of unit
on rear
of uniP
centerline
height for
rear vent
39"
(99cm)
Installed Washer Dimensions
1_ 48.25" (122,5cm)
to clear open door
freestand washer
fleer}ine
washer mounted on
optional pedestal
floorline
* To obtain these minimal depth dimensions, dryer must be vented straight back. Using a quick-turn 90° elbow (right or down on freestanding dryer) adds approximately 0.75 in. (2.0 cm) to
installation depth. Upward venting of exhaust on pedestabmounted or freestanding dryer adds approximately 4 in. (:[0.2 cm) to installation depth. Leftward venting on pedestabmounted or
freestanding dryer adds approximately 3.75 in. (9.5 cm) to installation depth. Downward venting of exhaust on pedestal-mounted dryer adds approximately 2.25 in. (5.7 cm) to installation
depth. These dimensions are based on matching 7.0 cu. ft. dryer. If matching dryer is 5.8 cu. ft. version with optional side venting knockouts, dimensions will vary.
_Hot and cold inlet hose length approximately 43 inches (:[09cm)
2Powersupply cord length approximately 60 inches (:[52.5cm).
3Drain hose length approximately 52 inches (:[32cm).
48,25"(122.5cm)
to clear open door
._--- 30.5" (77.5cm)*
on _oor
to front of closed door
to front of closed door
30.5" (77.5cm)* __
water supply
connection
on rear of unit _
27.0"
(68.5cm)
0
27.0
(68.5cm)
drain hose
of uniP
36.0"
(9:[.5cm)
[
(130cm)
51.25"
7:[.5"
(:[82cm)
water supply
connection
on rear of unit _
gas supply
pipe on rear
of gas unit
37"
(94cm)
0
0
power cord
on rear of unit z
electrical
supply on
rear of unit
hose
on rear
of unit _
centerline
height for
rear vent
39"
(99cm)
To obtain these minimal depth dimensions dryer must be vented straight back. Using a quick-turn 90° elbow (right) adds approximately 0.75 in. (2 cm) to installation depth. Upward
vent ng of exhaust on stacked dryer adds approx mately 4 n. (:[0.2 cm) to nstallat on depth. Downward vent ng of exhaust on stacked dryer adds approx mately 2.25 n. (6.5 cm) to
installation depth. Leftward venting of exhaust on stacked dryer adds approximately 3.75 in. (9.5 cm) to installation depth. These dimensions are based on matching 7.0 cu. ft. dryer. If
matching dryer is 5.8 cu. ft. version with optional side venting knockouts, dimensions will vary.
_Hot and cold inlet hose length approximately 43 inches (:[09cm)
2Powersupply cord length approximately 60 inches (:[52.5cm).
3Drain hose length approximately 52 inches (:[32cm).
Removing foam packaging
- SUFFOCATION HAZARD - Destroy the
carton and plastic bags after the washer is unpacked. Chil-
dren might use them for play. Cartons covered with rugs,
bedspreads, or plastic sheets can become airtight chambers
causing suffocation. Place all materials in a garbage container
or make materials inaccessible to children.
1. Temporarily remove door tape.
2. Open washer door and remove everything from the drum.
3. Close door and reapply door tape.
4. Using a rug, blanket or piece of cardboard to protect the
floor, carefully lay the washer on it's back.
- EXCESSIVE WEIGHT HAZARD - Toavoid
back or other injury, have more than one person move or lift
the washer.
5. Remove styrofoam base and shipping plug and set them
aside.
6. Carefully return the washer to an upright position.
7. Carefully move the washer to within 4 feet (1 m) of its
final location.
Savestyrofoam base and shipping plug for
use to help prevent washer damage during any future moves.
Removing shipping hardware
Remove all of the following:
4 BOLTS ® 4 SPACERS
2 P CLAMPS
Rubber expansion material on spacers may
need time to relax before they can be easily pulled
through shipping hole.
/ x4 x4
BOLTS
Saveall shipping bolts and spacers for future
use. If the washer is to be transported at a later date, the
shipping hardware must be reinstalled to help prevent ship-
ping damage.
Installing hole plugs
Ax4
/__ Locate 4 hole plugs in the small bag supplied
with washer instruction guides. Insert them in
A 4 HOLE PLUGS the holes in washer back panel.
(IN BAG)
Loading...