Page 1
SANTO
K 81200 i
K 88800 i
Built-In Refrigerators
Operating Instructions
Page 2
2
Dear customer,
Before placing your new refrigerator/freezer into operation please read
these operating instructions carefully. They contain important information for safe use, for installation and for care of the appliance.
Please keep these operating instructions for future reference. Pass
them on to possible new owners of the appliance.
These operating instructions are for use with several technically comparable models with varying accessories. Please observe the notes
which apply to your model.
Notes which are important for your safety or for the proper
functioning of the appliance are stressed with a warning triangle and/
or with signal words (
Warning!, Caution!, Important!). Please observe
the following carefully.
☞
1. This symbol guides you step by step in the operation of the appliance.
2.
Supplementary information regarding operation and practical
applications of the appliance appear after this symbol.
Tips and notes concerning economical and environmentally sound use
of the appliance are marked with the cloverleaf.
The operating instructions contain instructions for the correction of
possible malfunctions by the user in the section "What to do if ...". If
these instructions should not be sufficient, contact your local Service
Force Centre.
Printed on paper manufactured with environmentally sound proceses
he who thinks ecologically acts accordingly...
Page 3
3
Contents
Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Appliance Packaging Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Disposal of old Appliances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Remove transport packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Installation Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Your refrigerator needs air . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Electrical Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Description of the Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
View of the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Temperature setting buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Temperature display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Prior to Initial Start–Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Starting up and temperature regulation . . . . . . . . . . . . . . . . . . . . . . . .11
COOLMATIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Malfunctions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Switching off the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Holiday Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Interior Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Storage shelves/glass shelves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Variable Inner Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Humidity Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Variable Storage Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Bottle Holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Correct storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Defrosting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
The fridge defrosts automatically . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Cleaning and Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Energy Saving Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
What to do if ... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Correcting Malfunctions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Changing the light bulb . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Noises during Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Regulations, Standards, Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Technical terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Page 4
4
Important Safety Instructions
These warnings are provided in the interests of your safety. Ensure
you fully understand them before installing or using the appliance.
Your safety is of paramount importance. If you are unsure about the
meaning of these warnings contact the Customer Care Department
for assistance.
Intended use
• The refrigerator is intended for use in the home. It is suitable for the
storing of food at low temperature. If the appliance is used for purposes other than those intended or used incorrectly, no liability can
be accepted by the manufacturer for any damage that may be
caused.
• Alterations or changes to the refrigerator are not permitted for reasons of safety.
• If you use the refrigerator in a commercial application or for purposes other than the cooling of foods, the manufacturer accepts no liability for any damages which may occur.
Prior to initial start–up
• Ensure that the appliance does not stand on the electrical supply
cable.
Important: if the supply cable is damaged, it must be replaced
by authorised service or qualified personnel using a special cable of
the same type.
• Check the appliance for transport damage. Under no circumstance
should a damaged appliance be plugged in. In the event of damage,
please contact your supplier.
Refrigerant
The refrigerant isobutane (R600a) is contained within the refrigerant
circuit of the appliance, a natural gas with a high level of environmental compatibility, which is nevertheless flammable.
• During transportation and installation of the appliance, be certain
that none of the components of the refrigerant circuit become damaged.
• If the refrigerant circuit should become damaged:
– avoid open flames and sources of ignition;
– thoroughly ventilate the room in which the appliance is situated.
Page 5
Important Safety Instructions
5
Safety of children
• Packaging (e.g. wraps, polystyrene) can be dangerous for children.
There is a risk of suffocation! Keep packaging material away from
children!
• Please make old appliances unusable prior to disposal. Pull out the
mains plug, cut off the mains cable, break or remove spring or bolt
catches, if fitted. By doing this you ensure that children cannot lock
themselves in the appliance when playing (there is risk of suffocation!) or get themselves into other dangerous situations.
• Often children cannot recognise the hazards present in household
appliances. It is therefore important that you ensure adequate supervision and never let children play with the appliance!
Daily Operation
• Containers with flammable gases or liquids can leak at low temperatures. There is a risk of an explosion! Do not store any containers
with flammable materials such as spray cans, fire extinguisher refill
cartridges etc in the refrigerator and/or freezer.
• Do not operate any electrical appliances in the refrigerator and/or
freezer (e.g. electric ice cream makers, mixers etc.).
• Before cleaning the appliance, always switch off the appliance and
unplug it, or pull the house fuse or switch off the circuit breaker.
• When unplugging always pull the plug from the mains socket, do not
pull on the cable.
In case of malfunction
• If a malfunction occurs on the appliance, please look first in the
"What to do if ..." section of these instructions. If the information
given there does not help, please do not perform any further repairs
yourself.
• Under no circumstance should you attempt to repair the appliance
yourself. Repairs carried out by inexperienced persons may cause
injury or serious malfunctioning. Contact your local AEG Service
Force Centre.
Page 6
Disposal
Appliance Packaging Information
All materials are environmentally sound! They can be disposed of or
burned at an incinerating plant without danger.
About the materials: The plastics can be recycled and are identified as
follows:
>PE< for polyethylene, e.g. the outer covering and the bags in the
interior.
>PS< for polystyrene foam, e.g. the pads, which are all free of chlorofluorocarbon.
The carton parts are made from recycled paper and should be disposed
of at a waste-paper recycling collection location.
Disposal of old Appliances
For environmental reasons, refrigeration appliances must be disposed
of properly. This applies to your old appliance, and - at the end of its
service life - for your new appliance as well.
Warning! Before disposing of old appliances make them inoperable.
Remove plug from mains, sever the power cable, remove or destroy
any snap or latch closures. This ensures that playing children do not
lock themselves inside the appliance (danger of suffocation!) or place
themselves into other life-endangering situations.
Disposal:
• The appliance may not be disposed of with domestic waste or bulky
refuse.
• The refrigerant circuit, especially the heat exchanger at the back of
the appliance, must not be damaged.
• Information concerning collection schedules or locations can be
obtained from your local Council or Environmental Health Office.
Remove transport packaging
The appliance and the interior fittings are protected for transport.
☞
1. Pull off the adhesive tape on the left and right side of the door.
You can remove any remnants of adhesive using white spirit.
2. Remove all adhesive tape and packing pieces from the interior of the
appliance.
6
Page 7
7
Installation
Installation Location
The appliance should be set up in a well ventilated, dry room.
Energy use and efficient performance of the appliance is affected by
the ambient temperature.
The appliance should therefore
– not be exposed to direct sunlight;
– not be installed next to radiators, cookers or other sources of heat;
– only be installed at a location whose ambient temperature
corresponds to the climate classification, for which the appliance is
designed.
The climate classification can be found on the serial plate, which is
located at the left on the inside of the appliance.
The following table shows which ambient temperature is correct for
each climate classification:
If the refrigeration appliance is installed next to another refrigerator
or freezer a clearance of 5 cm at the sides is required, in order to prevent the formation of condensation on the outside of the appliance.
Climate classification for an ambient temperature of
SN +10 to +32 °C
N +16 to +32 °C
ST +18 to +38 °C
T +18 to +43 °C
Your refrigerator needs air
Integratable models (i-appliances)
The integrated door of the furniture cabinet largely seals the installation recess. iappliances must therefore be provided
with ventilation by having an opening in
the furniture plinth. The warmed air must
be able to be exhausted upwards through
the air shaft on the furniture back. The
ventilation cross-sections should be at
least 200 cm
2
.
min. 200 cm
2
50
min. 200 cm
2
Page 8
Installation
Warning - In order not to impair the function of the appliance, never
cover or obstruct the ventilation openings.
Electrical Connection
Any electrical work required to install this appliance should be carried
out by a qualified electrician or competent person.
WARNING – THIS APPLIANCE MUST BE EARTHED
The manufacturer declines any liability should these safety mea-
sures not be observed.
Before switching on, make sure the electricity supply voltage is the
same as that indicated on the appliance rating plate. The rating plate is
inside, on the left.
The appliance is supplied with a 13 amp plug fitted. In the event of
having to change the fuse in the plug supplied, a 13 amp ASTA
approved (BS 1362) fuse must be used.
Important
The wires in the mains lead are coloured in accordance with the following code:
Green and Yellow: Earth
Blue: Neutral
Brown: Live
As the colours of the wires in the mains lead
of this appliance may not correspond with
the coloured markings identifying the terminals in your plug, proceed as follows:
1.The wire coloured green and yellow must be
connected to the terminal marked with the letter “E” or by the earth
symbol or coloured green and yellow.
2.The wire coloured blue must be connected to the terminal “N” or
coloured black.
Installation
See installation instructions supplied.
Please check whether, after installing your appliance and especially
after reversing the door, the door seal seals right round. A badly fitting
door seal may lead to heavy frosting and thereby to a higher power
consumption (see also „What to do if...“).
8
GREEN & YELLOW
BLUE
13 AMP. FUSE
13 AMP
BROWN
CORD CLAMP
Page 9
Description of the Appliance
9
3.The wire coloured brown must be connected to the terminal marked
“L” or coloured red.
4.Upon completion there must be no cut, or stray strands of wire present and the cord clamp must be secure over the outer sheath.
Warning! A cut-off plug inserted into a 13 amp socket is a serious
safety (shock) hazard. Ensure that the cut-off plug is disposed of safely.
Description of the Appliance
View of the appliance
➀
Control panel
➁
Butter/cheese compartment
with flap
➂
Door storage compartment
with retaining rail (not for all
models)
➃
Door storage compartment
➄
Bottle shelf
➅
Vegetable drawers
➆
Storage shelves
➇
Moisture regulation
➈
Rating plate
Page 10
1 Pilot light (green)
2 ON/OFF switch
3 Temperature setting buttons (for warmer temperatures)
4 Temperature display
5 Temperature setting buttons (for colder temperatures)
6 COOLMATIC indicator light (yellow)
7 Push button for COOLMATIC
Description of the Appliance
Control panel
Temperature setting buttons
The temperature is adjusted using the „+“
(WARMER) and „-“ (COLDER) buttons.
These buttons are connected to the temperature display.
• The temperature display is switched over from the display of the
ACTUAL temperature (temperature display is illuminated) to the display of the DESIRED temperature (temperature display flashes) by
pressing one of the two buttons, „+“ or „-“.
• With each further press of one of the two buttons, the DESIRED
temperature is adjusted by 1°C.
• If neither button is pressed, the temperature display automatically
switches back after a short period (approx. 5 sec.) to the display of
the ACTUAL temperature.
DESIRED temperature means:
The temperature that is required in the refrigerator, this can be adjust-
ed to the temperatures shown in the display. The DESIRED temperature
is indicated by flashing numbers.
ACTUAL temperature means:
The temperature display indicates the temperature that is currently
present in the refrigerator. The ACTUAL temperature is indicated by
continuously illuminated numbers.
10
Page 11
11
Temperature Display
The temperature display can indicate several pieces of
information.
• During normal operation, the temperature currently present in the
refrigerator (ACTUAL temperature) is displayed.
• When the temperature is being adjusted, the temperature currently
set flashes (DESIRED temperature).
Prior to Initial Start–Up
Please clean the appliance interior and all accessories prior to initial
start-up (see section “Cleaning and Care”).
☞
Starting up and temperature regulation
☞
1. Insert the plug into the plug socket. When the refrigerator compartment door is opened, the internal lighting is switched on.
2. Press ON/OFF button.
The green mains pilot indicator illuminates.
3. Press either the „+“ (WARMER) or „-“ (COLDER) button.
The temperature display switches over and the DESIRED temperature
currently set flashes on the temperature display.
4. Set the required temperature by pressing the „+“ (WARMER) or „-“
(COLDER) buttons (see section "Temperature setting buttons"). The
temperature display will immediately show the changed setting. With
each further press of one of the two buttons, the DESIRED temperature is adjusted by 1°C. Adjustable temperature range: +2°C to +8°C.
From a food safety point of view +5 °C should be considered sufficiently cold for storing food in the fridge.
5. Once the required temperature has been set, after a short period
(approx. 5 sec.) the temperature display will change and again indicate
the current ACTUAL temperature inside the fridge. The display will
change from flashing to continuous illumination.
The compressor will start and then run automatically.
Information! When the setting is changed, the compressor does not
start immediately if automatic defrosting is currently taking place.
As the storage temperature within the fridge is reached quickly you
can store food immediately after switching on.
Page 12
COOLMATIC
COOLMATIC Button
The COOLMATIC function is suited for quick cooling of
large quantities of goods in the refrigerator, e.g. drinks
and salads for a party.
☞
1. The COOLMATIC function is switched on by pressing the COOLMATIC
button. The yellow light illuminates.
2. The COOLMATIC function now provides for intensive cooling. A
DESIRED temperature of +2°C is automatically selected. The COOLMATIC function is ended automatically after a period of 6 hours. The
originally selected DESIRED temperature is again valid. The temperature display shows the ACTUAL refrigerator temperature.
3. The COOLMATIC function can be ended manually at any time by pressing the COOLMATIC button again. The yellow light goes out.
If the COOLMATIC function is switched on the temperature setting
may not be changed.
Malfunctions
If the electronics in the appliance have detected a fault that prevents
the ACTUAL temperature being measured, the temperature display will
flash. The appliance will continue to function using a backup program
until your local Service Force engineer has repaired the appliance.
Switching off the appliance
☞
To switch off, press the ON/OFF button for approx. 5 seconds. This will
result in a countdown from "3" to "1" taking place in the temperature
display. On reaching "1" the fridge will switch off. The temperature display will go off.
If the appliance is not going to be used for an extended period:
☞
1. Remove all refrigerated packages.
2. Switch off the appliance by holding down the ON/OFF button until the
display goes off (see above).
3. Remove the mains plug or switch off or disconnect the electricity supply.
12
Page 13
Holiday Setting
13
4. Clean thoroughly (see section “Cleaning and Care”).
5. Leave the door open to avoid the build up of odours.
Holiday Setting
In the holiday mode the temperature for the refrigerator is approximately +15°C. In the holiday mode it is therefore possible to leave the
door of the empty refrigerator closed during periods of extended
absence.
Advantage: Unintentional closing of the door, or accidental closing of
the door by persons who have access to your home during your
absence, is no longer possible. Without the stand-by mode leaving the
door closed would lead to the accumulation of odours and mould.
After emptying and cleaning the appliance, proceed as follows:
☞
1. To activate the holiday setting, press the „+“ (WARMER) or „-“ (COLDER) button.
The temperature display will change and indicate in flashing numbers
the DESIRED temperature that is currently set.
2. Hold down the „+“ (WARMER) button until the temperature display
indicates H (for holiday). The temperature shown in the temperature
display will change in steps of 1°C until it reaches +8°C. After +8°C the
value +15°C will appear in the display with the letter H. The fridge is
now operating in energy-saving holiday mode.
3. After a few seconds the temperature display will again change to the
ACTUAL temperature. The display will change from flashing to continuous illumination.
To switch the fridge back to normal operation, press the „-“ (COLDER)
button.
Important! Do not store any goods in the refrigerator when the standby mode is operational. The temperature is regulated at about +15°C
when the stand-by mode is operational. This is too warm for food products.
Page 14
14
Variable Inner Door
The door compartments can be pulled up and removed, and inserted at
other positions as needed.
Interior Accessories
Storage shelves/glass shelves
Various glass or plastic storage shelves and wire trays are included with
your appliance - different models have different combinations.
You should always slide one of the full size glass storage shelves into
the lowest set of guides, above the vegetable drawers, and keep it in
this position.
The height of the storage shelves can be adjusted:
☞
1. To do this pull the storage shelf forward until it can be swivelled
upwards or downwards and
removed.
2. Please do the same in reverse to
insert the shelf at a different height.
Your appliance is equipped with two half-size glass storage shelves.
Storing tall items:
Slide the front half of the Vario storage shelf in another level to the rear.
By this means you will gain space to
place tall items on the storage shelf
below.
☞
☞
Page 15
Interior Accessories
15
Humidity Control
On some models, there is an adjustable air grille in front of the shelf
above the fruit and vegetable compartments.
The opening in the ventilation slots can be adjusted with a slider.
Slider in right position: Ventilation
slots opened.
Slider in left position: Ventilation
slots closed.
With the ventilation slots open, the
stronger air circulation results in a
lower air moisture content in the
fruit and vegetable compartments.
When the ventilation slots are
closed, the natural moisture content of the food in the fruit and vegetable compartments is preserved for longer.
Variable Storage Box
(not on all models, design differs depending on the model)
Some models are equipped with a variable storage box which is fitted
under a door shelf compartment and can be slid sideways.
The box can be inserted under every door shelf compartment.
☞
1. To change, lift the shelf compartment with the box upwards and
out of the holders in the door and
remove the retaining bracket out
of the guide under the shelf compartment.
2. Please do the same in reverse to
insert the shelf at a different
height.
The variable box can be hung from a
storage shelf in the refrigerator compartment:
☞
1. Pull the storage shelf forward until it
can be tipped up or down and removed.
2. Hang the retaining bracket on the taper
on the storage shelf and slide the storage shelf back into the guides.
Page 16
Correct Storage
16
Correct storage
For physical reasons, there are different
temperature regions in the fridge. The
coldest region is on the lowest storage
shelf. Warmer regions are the top storage shelf, the vegetable drawer and the
storage compartments on the door.
The arrangement example shows at
which places in the refrigerator suitable temperatures for various types of
foods exist.
Tip: Food in the fridge should always
be covered or packaged, to prevent
drying and tainting of other food.
The following are suited for packaging:
– Polyethylene airtight bags and wraps;
– Plastic containers with lids;
– Special plastic covers with elastic;
– aluminium foil.
Bottle Holder
(not included with all models)
Some models are equipped with a bottle
holder in the bottle compartment. This is
used to prevent individual bottles from
falling over and can be slid sideways.
Page 17
17
Cleaning and Care
For hygienic reasons the appliance interior, including interior accessories, should be cleaned regularly.
Warning!
• The appliance may not be connected to the mains during cleaning.
Danger of electrical shock! Before cleaning switch the appliance off
and remove the plug from the mains, or switch off or turn out the
circuit breaker or fuse.
• Never clean the appliance with a steam cleaner. Moisture could
accumulate in electrical components, danger of electrical shock! Hot
vapours can lead to the damage of plastic parts.
• The appliance must be dry before it is placed back into service.
Important!
• Ethereal oils and organic solvents can attack plastic parts, e.g.
– lemon juice or the juice from orange peel;
– butyric acid;
– cleansers which contain acetic acid.
Do not allow such substances to come into contact with appliance
parts.
• Do not use any abrasive cleansers.
☞
1. Remove the food from the refrigerator. Store it in a cool place, well
covered.
2. Switch the appliance off and remove the plug from the mains, or
switch off or turn out the circuit breaker or fuse.
3. Clean the appliance and the interior accessories with a cloth and lukewarm water with a little bicarbonate of soda added (5ml to 0,5 litres
of water).
Defrosting
The fridge defrosts automatically
The rear wall of the fridge covers with frost when the compressor is
running, and defrosts when the compressor is off. The water from the
thawing frost evaporates by itself.
The water drainage hole must be cleaned regularly (see the section
"Cleaning and Care").
Page 18
Energy Saving Tips
• Do not install the appliance near cookers, radiators or other sources
of warmth. High ambient temperatures cause longer, more frequent
operation of the compressor.
• Ensure sufficient air circulation and exhaust at the appliance base
and at the back wall of the appliance. Never cover air vent openings.
• Do not place warm foods into the appliance. Allow warm foods to
cool first.
• Only leave door open as long as necessary.
• Do not set temperature any colder than necessary.
What to do if ...
Correcting Malfunctions
A malfunction may be caused by only a minor fault that you can rectify yourself using the following instructions. Do not perform any other
work on the appliance if the following information does not provide
assistance in your specific case.
Important! Repairs to refrigerators/freezers may only be performed by
competent service engineers. Improper repairs can give rise to significant hazards for the user. If your appliance needs repairing, please
contact your specialist dealer or your local Service Force Centre.
4. After cleaning wipe with fresh water and rub dry.
5. Check the water drain hole on the
rear wall of the fridge.
Clear a blocked drain hole with the
aid of the green peg in the pack of
accessories included with the appliance.
6. After everything is dry place appliance back into service.
18
Page 19
What to do if ...
19
Symptom
Appliance does not work.
Possible Cause
Appliance is not switched
on.
Mains plug is not plugged
in or is loose.
Fuse has blown or is
defective
Socket is defective.
Mains malfunctions are to
be corrected by an electrician.
The food is too warm.
Temperature is set too
cold.
Temperature is not properly adjusted.
Turn the temperature regulator to a warmer setting
temporarily.
Please look in the “Starting
up and Temperatur regulation” section.
Remedy
Switch on the appliance.
Insert mains plug.
Check fuse, replace if
necessary.
Light bulb is defective.
Interior lighting does not
work.
Heavy build up of frost,
possibly also on the door
seal.
Appliance cools too much.
Door was open for an
extended period.
A large quantity of warm
food was placed in the
appliance within the last
24 hours.
The appliance is near a
heat source.
Door seal is not air tight
(possibly after reversing
the door).
Carefully warm the leaking
sections of the door seal
with a hair dryer (on a
cool setting). At the same
time shape the warmed
door seal by hand such
that it sits correctly.
Open the door only as long
as necessary.
Turn the temperature
regulator to a colder setting temporarily.
Please look in the
“Installation location” section.
Please look in the “Changing
the light bulb” section.
The compressor does not
start immediately after
changing the temperature
setting.
This is normal, no error has
occurred.
The compressor starts after
a period of time.
Page 20
What to do if ...
20
Symptom Possible Cause Remedy
Temperature cannot be set
COOLMATIC function
switched on.
Switch off COOLMATIC
manually, or wait to set
the temperature until the
function has reset automatically (refer also to
COOLMATIC section).
Water on the floor or on
storage shelves.
Water drain hole is
blocked.
See the “Cleaning and
Care” section.
Changing the light bulb
Warning! There is a risk of electric shocks! Before changing the light
bulb, switch off the appliance and unplug it, or disconnect from the
mains supply.
Light bulb data: 220-240 V, max. 25 W
☞
1. To switch off, press the ON/OFF button until the mains power light
extinguishes.
2. Unplug the mains plug.
3. To change the light bulb, undo the
screw.
4. Press the light bulb cover as shown and
slide it towards the rear of the appliance.
5. Change the faulty light bulb.
6. Refit the light bulb cover and the screw.
7. Put the refrigerator back into operation.
Page 21
21
Regulations, Standards, Guidelines
This appliance was designed for household use and was manufactured
in accordance with the appropriate standards. The necessary measures
in accordance with appliance safety legislation regulations (GSG), accident prevention regulations for refrigeration appliances (VBG 20) and
the regulations of the German Society of Electrical Engineers (VDE)
were observed in the manufacture of this appliance.
The refrigerant circuit has been checked for leaks.
This appliance is in accordance with the following EU guidelines:
– 73/23/EWG dated 19 February 1973 - low voltage guidelines.
– 89/336/EWG dated 3 May 1989 (including guideline change notice
92/31/EWG) - EMV guideline
Noises during Operation
The following noises are characteristic of refrigeration appliances:
•
Clicks
Whenever the compressor switches on or off, a click can be heard.
•
Humming
As soon as the compressor is in operation, you can hear it humming.
•
Bubbling/Splashing
When refrigerant flows into thin tubes, you can hear bubbling or
splashing noises. Even after the compressor has been switched off,
this noise can be heard for a short time.
Page 22
22
Technical terminology
• Refrigerant
Liquids that can be used to a generate a cooling effect are known as
refrigerants. They have a relatively low boiling-point, indeed so low,
that the warmth from the food stored in the fridge or freezer can
cause the refrigerant to boil and vaporise.
• Refrigerant Circuit
Closed circulation system that contains the refrigerant. The refrigerant circuit comprises primarily of an evaporator, a compressor, a condenser and pipe work.
• Evaporator
The refrigerant is evaporated in the evaporator. Similar to all other
liquids, refrigerant requires heat to evaporate. This heat is removed
from the interior of the appliance, as a result the interior is cooled.
The evaporator is therefore located inside the appliance or placed in
foam immediately behind the inner wall and thus not visible.
• Compressor
The compressor looks like a small drum. It is driven by a built-in
electric motor and is mounted on the base of the appliance at the
rear. The task of the compressor is to draw in vaporised refrigerant
from the evaporator, to compress it, and to pass it on to the condenser.
• Condenser
The condenser normally has the form of a grid. The refrigerant compressed in the compressor is liquefied in the condenser. During this
process, heat is released to the surrounding air at the surface of the
condenser. The condenser is mounted on the base of the appliance.
Page 23
Page 24
AEG Hausgeräte GmbH
Postfach 1036
D-90327 Nürnberg
http://www.aeg.hausgeraete.de
© Electrolux plc 2003
2222 634-51 -02- 0203 Subject to change without notice
Loading...