Electrolux Gl44ngdc, Gl44hongdc, Gl44lpdc, Gl44holpdc Owner's Manual

Lighting the Grill ..................... 13

Care & MaintenanGe ...............16

Before You Call

T_oub_e Shoot_ng .............17-18

Vidt the Rrigidaire Web Site at:

READ AND SAVE THESE INSTRUCTIONS - MADE IN THE U.SoAo

Wsrrant_ ......................... 19

Congratulations on your purchase of a new gas grill! At Electrolux Home Products, we are very proud of our product and are completely committed to providing you with the

best service possible. Your satisfaction is our number one priority.

We know you'll enjoy your new gas grill and Thank You for choosing our product. We hope you consider us for future purchases.

PLEASE CAREFULLY READ AND SAVE THESE INSTRUCTIONS

This Use & Care Manual provides specific operating instruction for your model. Use your gas grill only as instructed in this manual. These instructions are not meant to cover every

possible condition and situation that may occur. Common sense and caution must be practiced when installing, operating and maintaining any appliance.

Questions? 1-800-320-0859

Please record Grill information for future reference and service work:

Model #:

Serial #:

Date of Purchase:

Gas Type:

Please retain this manual for future reference

IMPORTANT SAFETY INFORMATION

- Read this manual carefully before using your grill to reduce the risk of fil_, bum hazard or other injury.

- Extreme cam should be used because of the high telnperatures produced by this appliance. CHILDREN SHOULD NOT BE LEFT UNATTENDED IN AN AREA WHERE THE ()RILL IS BEING OPERATED.

- This appliance must be kept clear from combustible materials, gasoline or other flammable vapors and liquids. Do not allow flalmnable materials to come in contact with grate, burner or hot surfaces.

- Do not repair or replace any part of this appliance unless it is specifically recommended in this manual. A qualified service techni- cian should conduct all other service.

- Follow the installation and servicing instructions provided with this product. Have your grill installed by a qualified service techni- cian. Locate the main gas supply valve so that you know how to shut the gas off to your grill. If you smell gas, make sum all gas

connections are tight before operation. If you continue to smell gas call a qualified technician.

- When lighting a burner, always pay close attention to what you am doing. Be certain you are pushing the ignitor that lights the burner you intend on using.

Roll top grill hood

Grilling/Cooking surface

Side Shelf

10.

Warming shelf

Infrared back burner

Electronic ignitors: main, rear infrared

& side burner

Control knob: back infrared burner

Control knobs: main burners

Warming drawer

tlandle

11.

12.

13.

14.

Cart w/doors

Drip Pans

Side Burner

Control knob:side burner

Note: Prior to assembly remove protective film from stainless steel parts

Battery:r i_ ii I

Ignitor Attachment

1. Remove the ignitor cap, spring assembly, bat- tery and lock nut from ignitor. (See Fig. 1)

Insert the threaded section of the ignitor into the U-shaped cut out of the ignitor mounting

bracket. (See Fig. 2)

Insert the threaded section of the ignitor

through the hole in the shelf and secure to

shelf using the lock nut. (Use the ignitor assembly diagrams to determine which

ignitor goes with which shelf depending on grill model.) Tighten Securely. (See Fig. 3)

Cap

Spring Assembly

Nut Cylinder Bracket

Fig. 1

Fig. 2

Fig. 3

Re-insert the battery, positive side first, and spring assembly and attach the ignitor cap.

(See Fig. 4)

Repeat above steps for second ignitor on the Side Burner.

GL44 Ignitor Assembly

Side Burner (Three Wire)

Fig. 4

Left Shelf (Double Wire)

Side Shelf and Side Burner Attachment

1. Loosen the bolts on the side of'the grill and attach the shell" by allowing the bolt heads to fall through the large opening in the bottom of"

the keyhole slots. Then slide the shelves downward until the bolts are resting against

the top of'the key hole slots. Tighten all of" the shell" bolts. (See Fig. 5)

Attach the wires coming out from the sides of the grill to the ignitor terminals. (See Fig. 6)

Note: It does not matter which wire goes to which

terminal on the double wire ignitor

Attach the side burner by allowing the bolt heads to fall through the large opening in the

bottom of the keyhole slots. Then slide the sine burner aownwara until me boltS are

resting against the top of the key hole slots. Tighten all of the side burner bolts.

Screw the Flex Line coming from the side of the grill to the fitting on the bottom of the

Side Burner. (See Fig. 7)

Fig. 5

Fig. 6

Fig. 7

Attach the ignitor wires coming out from the side of the grill to ignitor terminals.

(See Fig. 8)

Note:

It does not matter which wire goes to which

terminal on the three wire ignitor

Install burner into side burner tray lining up the three cutouts on the underside of the

burner. (See Fig. 9)

5. Install burner cap onto burner (See Fig. 10)

Fig. 10

Fig. 8

wires hookup

Fig. 9

+ 14 hidden pages