Electrolux E30MO75HPSA, EW27MO55HSA, EW30MO55HSA, EW30SO60QSB Installation Guide
Installation and service must be pefformed byaqu , i lstaller.
IMPORTANT: Save for local electrical inspector s use,
Read and Save these instructions for future
Th e e lectricalreq u ire m ents fo r t his ova n a re 120vo Itsi 15 a rnps!
NOTE
Base must be capable of supporting 150 pounds (68.0
kg) for the Microwave Wall Oven only.
2,
Make sure base is level and front of cabinet is square. If
the cabinet base is not level, the oven will tend to slide
out when opening the door.
3,
Minimum required distance is 36" (91.44 cm) from the
floor.
4,
The outlet should not be located in the shaded area of
Figure 1. It is required the outlet be a dedicated 120
volts with a 15amp rating for the appliance.
5,
Minimum required distance between the Microwave
Oven and the wall oven cutouts should be at least 3
inches. The actual visible space will be reduced due to
the overlap of the Microwave Oven lower vent and the
wall oven.
All dimensions are in inches (cm).
Figure I
TINSEB504MRRO
iMPORTANT NOTES TO
iMPORTANT SAFETY
THE iNSTALLER
,
Read all instructions contained in these installation
instructions before installing the Microwave Wall Oven.
This oven can be built into a cabinet or wall by itself or
above any electric wall oven or warming drawer.
,
Remove all packing material from inside the oven cavity
before connecting the electrical supply to the Microwave
Wall Oven. DO NOT REMOVETHE WAVEGUIDE COVER,
which is located on the cavity ceiling. See Figure 2A.
Waveguide Cover
Oven Cavity
Door Seals
and Sealing
Surfaces
Hinge
Safety
Door Latch
Figure 2A Figure 2B
iNSTRUCTiONS
ventilation can be dangerous.
Carpentry
Refer to Figure 1 for the dimensions required for your
appliance, and the space necessary to install the oven. The
oven support surface should be solid plywood or similar
material, the surface must be level from side to side and
from front to rear.
Electrical Requirements
The appliance operates on a 120 volt, 60 Hz electrical
supply with a separate ground wire. Provide a separate
circuit with a fuse or circuit breaker rated for 15 amps.
Observe all governing codes and local ordinances
,
Remove the 2 shipping duct supports (see Figure 2B) by
removing the 2 screws securing each side. Reinsert 2
screws (each side) to secure the stainless cover.
,
Remove the feature sticker, if there is one, from the
outside of the door.
,
Check the oven for any damage, such as misaligned or
bent door, damaged door seals and sealling surfaces,
broken or loose door hinges and latches and dent
inside the cavity or on the door.
AUTHORIZED SERVICER
6. Observe all governing codes and local ordinances.
7. Be sure to leave these instructions with the consumer.
iMPORTANT NOTE TO
THE CONSUMER
Keep these instructions with your Owner's Guide for future
reference.
T0p"event damage to the oven contio!: duiing _old
ternperature weather, wait at least three (3)hours
after receiying this oven before supplyieg power to
the appliance. Thiswill prevent possibledamage to the
buiBin ovencontrol at power on.
Cabinet Installation
The Mkrowave Wall oven can tip when the door
is open, The Anti-Tip brackets supplied with th e
Microwave Wall Oven must be attached to the
cabinet and the appliance t0 prevent tipping of
the unit and injury to persons;
ANTI41P BRACKETS INSTALLATION
INSTRUCTIONS
Unpack the Microwave Wall Oven and find the 2
Anti-Tip brackets and screws included in the literature
package.
,
Install the Anti-Tip bracket in the cabinet as shown
on Figure 3. Note: To prevent damage to cabinet, it
is recommended to drill 1/16"(0.16 cm) diameter pilot
holes before installing the Anti-Tip brackets.
E2
Loading...