Thank you for buying an ELECTROLUX DOMESTIC APPLIANCE
To enable you to use your appliance effectively and safely, please read this instruction
book carefully before using the appliance and retain for future reference. If you require
guidance in the use of the appliance or require further information, please contact our
Customer Care Department.
CUSTOMER CARE
ELECTROLUX
PO BOX 47
NEWBURY
BERKSHIRE
RG14 5XL
TEL: 01635 522799
Guide to use the instruction book
The following Symbols will be found in the text to guide you through the instructions
Safety InstructionsHints and Tips
Step by step instructionsEnvironmental Information
for an operation
2
Page 3
IMPORTANT SAFETY INSTRUCTIONS
These warnings are provided in the interests of your safety. Ensure that you understand them
all before installing or using this appliance. Your safety is of paramount importance. If you are
unsure about any of the meanings or these warnings contact the Customer Care Department.
Installation
This appliance is heavy. Care should be taken
when moving it.
It is dangerous to alter the specifications or
attempt to modify this product in any way.
Ensure that the appliance does not stand on
the electrical supply cable. If the supply cord
is damaged, it must be replaced by a special
cord available from your local Service Force
Centre.
Any electrical work required to install this
appliance should be carried out by a qualified
electrician or competent person.
Parts which heat up should not be exposed.
Whenever possible, the back of the appliance
should be close to a wall but leaving the
required distance for ventilation as stated in
the installation instructions.
The appliance should be left for 2 hours after
installation before it is turned on, in order to
allow the refrigerant to settle.
Child Safety
Do not allow children to tamper with the
controls or play with the product.
Maintenance and Cleaning
Switch off, and unplug the appliance before
carrying out any cleaning or maintenance
work.
Servicing
This product should be serviced by an
authorised engineer, and only genuine spare
parts should be used.
Under no circumstances should you attempt
to repair the machine yourself. Repairs carried
out by inexperienced persons may cause
injury or serious malfunctioning. Contact your
local Service Force Centre.
At the End of the appliance Life
When disposing of your appliance, use an
authorised disposal site.
Remove the plug and ensure that any locks or
catches are removed, to prevent young
children being trapped inside.
During Use
This appliance is designed for domestic use
only, specifically for the storage of edible
foodstuffs only.
Frozen food should not be refrozen once it
has thawed out.
Do not place carbonated or fizzy drinks in the
freezer.
Ice lollies can cause 'frost/freezer burns' if
consumed straight from the freezer.
Do not remove items from the freezer if your
hands are damp/wet, as this could cause skin
abrasions or frost/freezer burns.
Manufacturers' recommended storage times
should be adhered to. Refer to relevant
instructions
.
Please read this
instruction book carefully
before use and retain
for future reference.
3
Page 4
TABLE OF CONTENTS
For the User
Important Safety Instructions3
Description of the Appliance5
Control Panel5
Using Your Appliance6
Before Use6
To Start The Appliance6
Thermostat Control6
Mains On / Off Switch7
Indicator Light7
Low Ambient Temperature Control7
Larder Compartment8
If these temperatures are exceeded i.e.,
colder or warmer, the appliance will not
operate correctly. Should the ambient
temperatures be exceeded for long periods,
the temperature in the freezer section will rise
above -18°C and food spoilage may occur.
Before Use
Remove all securing tapes.
Wash the inside of the appliance with lukewarm
water with a little bicarbonate of soda added (5ml
to 0.5 litre of water). Do not use soap or
detergent as the smell may linger. Dry the
appliance thoroughly.
Do not use detergents, abrasive
powders, highly perfumed cleaning
products, wax polishes or products
containing alcohol.
To Start the Appliance
1. Allow the appliance to stand for 2 hours
after installation.
2. Plug in the appliance and switch on at the
mains supply.
3. Turn the thermostat control to the required
setting. A midway setting is usually suitable
for normal operation (see thermostat control).
4. Leave the appliance for approximately 4 hours
for the correct temperature to be reached
before placing food inside.
Thermostat Control
The thermostat control is situated under the flap
at the front of the top panel. The thermostat
control is marked from min to max.
Min (Cold)
Max (Coldest)
The temperature will be affected by:
Room temperature
How often the door is opened
How much food is stored
Position of the appliance
In determining the correct temperature control
setting, all these factors have to be considered
and some experimentation may be necessary
Do not allow children to tamper with the
controls or play with the product.
6
.
Page 7
Mains On / Off Switch
For the appliance to operate this switch must be
in the I position as well as it being plugged into
the mains supply.
Indicator Light
The green indicator light is situated in the control
panel under the flap.
When the appliance is switched on at the mains
the green indicator light will glow and continue to
glow until the appliance is switched off at the
mains.
GREEN INDICATOR LIGHT
LOW AMBIENT TEMPERATURE CONTROL
Your appliance has been designed to operate in
room temperatures of 10°C to 32°C.
By use of an air circulation slider control situated
at the rear of the fridge compartment the amount
of cold air circulated through the fridge
compartment can be varied.
In room temperatures of between 10°C and 16°C,
should you find your fridge temperatures too cold,
reposition the slider control to the "cold" position.
NB. Positioning the slider control to the "cold"
position does not stop the flow of cold air, only
restrict it.
At room temperatures above 16°C the slider
control can be adjusted between "cold" and
"coldest" to increase the amount of cold air
circulating through the fridge compartment.
Maximum circulation will be achieved with the
slider control set at "coldest".
Any further fridge temperature adjustment should
be carried out by using the thermostat control
(see section headed "Thermostat Control").
7
Page 8
Larder Compartment
The correct temperature for safe storage of fresh food inside is 0°C to 5°C (32°F to 41°F). The warmest
part of the fridge compartment is at the top of the cabinet and the coolest at the bottom.
Store light items such as small cartons and jars
on the shelves provided in the door. The bottle
shelf can be used for the storage of heavier
bottles.
The bottle grippers must be fitted to the bottom
bottle shelf to ensure bottles are retained
securely. Fit the bottle grippers as shown.
The larder compartment is fitted with shelving
which are adjusted for the storage of different
sized articles.
If the door cannot be opened further than 90°
remove the shelves by tilting the shelf downwards
and pulling outwards.
8
Page 9
The Freezer Compartment
The symbol means that your freezer will
store frozen food at -18
allowing for long term frozen food storage and
freezing of fresh food. The freezer temperature is
controlled automatically by the thermostat
situated in the control panel.
°C (-0.4°F) or colder
Freezing Fresh Foods
The maximum quantity of food you can freeze in
24 hours is 6kg. Place the fresh food in the
bottom two baskets. Food may need rearranging
to achieve this.
Frozen food should not be refrozen
once it has thawed out.
Due to the different installations, methods of
usage and weather conditions, adjustments to the
temperature settings may be required.
These are best assessed against a
temperature reading on a thermometer
buried in the frozen food. The reading
must be taken quickly as the thermometer
temperature will rise rapidly after removal.
Frozen Food Storage
The appliance has the following net storage
volume:
103 litres (3.6 cuft)
32.3 kg (71.3 lb)
†This is a standard measurement and the
actual capacity depends upon the density
and sizes of the food. The above figures are
based on an average density of 0.32kg per
litre (20 lb per cuft).
Pre packed commercially frozen food should be
stored in accordance with the manufacturer's
instructions for a 4 star frozen food compartment
and should be put in the freezer as soon as
possible after purchase. Your freezer provides for
long term storage which generally means up to 3
months but the length of the time can vary and it
is important to follow the recommended times
shown on packets of commercially frozen food.
†
Do not remove items from the freezer if
your hands are damp/wet, as this could
cause skin abrasions or 'frost/freezer
burns'.
Hints and Tips
Any opened packets of frozen food,
should be rewrapped in airtight materials
to prevent surface evaporation which
cause s drying or 'freezer burn'.
Frozen food which is allowed to thaw
accidentally should either be used
immediately or thrown away. Alternatively
if the food is uncooked and has not been
completely defrosted it can be cooked and
then refrozen.
Aim to check dates on packets and rotate
food regularly. Although storage longer
than recommended is not harmful, flavours
and textures begin to change.
Do not place sealed containers or
carbonated liquids such as fizzy drinks
into the freezer as it creates pressure
on the container which may cause it to
explode resulting to damage to the
freezer.
Ice cubes and ice lollies should not be
consumed immediately after removal
from the freezer as it may result in low
temperature skin abrasions.
Manufacturers storage times should be
adhered to.
9
Page 10
HINTS AND TIPS
Food Storage
To obtain the best results from your appliance,
neither hot foods nor liquids which may
evaporate, should be placed in the larder
compartment.
Avoid buying frozen food if you cannot store it
straight away. The use of an insulated
container is advisable. When you arrive home
place the frozen food in the freezer
immediately.
Keep the time between buying chilled food
and placing it in your fridge as short as
possible.
Do not push food together too much, try to
allow air to circulate around each item.
Do not store food uncovered.
Ensure that food is placed in the freezer that
is dated and labelled and used in date order
to ensure that food is consumed at its best.
Remove suspect food from your refrigerator
and clean, refer to cleaning and maintenance.
Thaw frozen food in the fridge. This will
ensure safer defrosting of foods and reduce
the work of the refrigeration unit.
Try to avoid keeping the door open for long
periods, or opening the door too frequently as
warm air will enter the cabinet, and cause the
compressor to switch on unnecessarily often.
Ensure there are no obstructions preventing
the door from closing properly.
It is advisable to periodically clean the
refrigeration system at the back of the
appliance with a duster or vacuum cleaner.
In the Event of a Power Failure
If there is a power failure during the storage of
frozen foods, keep the door closed. If the
temperature within your freezer should rise do not
refreeze the food without checking it's condition.
The following guidelines should assist you:
Ice Cream: Once thawed should be discarded.
Fruit and Vegetables: If soft should be cooked
and used up.
Energy Saving Advice
Do not install the cabinet close to sources of
heat, such as a cooker, dishwasher or
radiator.
Locate the appliance in a cool well ventilated
room and make sure that the air openings of
the cabinet are not obstructed.
Avoid unnecessary frosting in the cabinet by
packing all foodstuffs into airtight packages
before placing them in the freezer.
Always leave warm food to cool down to room
temperature before placing in the fridge or
freezer.
Food which is to be frozen (when cool) should
be placed in the fridge before being
transferred to the freezer.
Bread and Cakes: Can be refrozen without
danger.
Shellfish: Should be refrigerated and used up
quickly.
Cooked Dishes: i.e. casseroles, should be
refrigerated and used up.
Large Pieces of Meat: Can be re-frozen
providing there are ice crystals remaining within
them.
Small Joints: Should be cooked and then
re-frozen as cooked dishes.
Chicken: Should be cooked and re-frozen as a
fresh dish
.
10
Page 11
HINTS AND TIPS
Normal Operating Sounds
The advanced design of today's frost free appliances mean you hear unfamiliar noises
during everyday operation. The diagram below describes some of the noises you may hear.
These are quite normal and mean your appliance is operating correctly.
The automatic defrost timer
sounds like an electric clock
and clicks in and out of the
The thermostat control will
click when starting or
stopping the compressor.
defrost cycle.
The fan circulates cold air to
cool the refrigerator and the
freezer compartment and
sounds like air blowing or a
whirring sound.
Defrost water drips into the
drain pan during the defrost
cycle.
The flow of refrigerant
through the freezer cooling
coil makes a gurgling noise.
Water dropping on the defrost
heater causes a hissing or
popping sound during the
defrost cycle.
The compressor will make a
hum or pulsating sound while
operating.
11
Page 12
MAINTENANCE AND CLEANING
Before any maintenance or cleaning work
is carried out DISCONNECT the appliance
from the ELECTRICITY supply.
Internal Cleaning
Clean the inside and accessories with warm water
and bicarbonate of soda (5ml to 0.5 litre of water).
Rinse and dry thoroughly.
Do not use detergents, abrasive powders,
highly perfumed cleaning products, wax
polishes or cleaning products containing
bleach or alcohol.
Regularly check the door seals and wipe clean to
ensure they are clean and free from debris.
External Cleaning
Wash the outer cabinet with warm soapy water.
Do NOT use abrasive products.
There are sharp edges on the underside
of the product so care should be taken
when cleaning.
Once or twice a year dust the condenser (black
grille) and the compressor at the back of the
appliance, with a brush or vacuum cleaner, as an
accumulation of dust will affect the performance
of the appliance and cause excessive electricity
consumption.
To Change the Light Bulb
1.Switch off the appliance and disconnect
from the electricity supply.
2.Remove the light cover by removing the
screw at the rear with a screwdriver.
3.Pull the cover outwards towards the
middle of the cabinet.
4.Unscrew the bulb and replace it with a
new 15 watt E14 SES bulb (available from
your local Service Force Centre).
5.Replace the cover by sliding it into its
original position.
6.Replace the screw.
Automatic Defrosting
Your appliance has been designed to be frost
free. This means there is no need to defrost your
appliance as this will be carried out automatically.
When the Appliance is Not in Use
When the appliance is not in use for long periods,
disconnect from the electricity supply, empty all of
the food and clean the appliance, leaving the
door ajar to prevent unpleasant smells.
12
Page 13
WHAT HAPPENS IF SOMETHING GOES WRONG
BEFORE contacting your local service force centre, check the following points:
SymptomSolution
No power to the applianceCheck there is power at the socket.
Check there is not a power cut by checking the
household lights.
Check the fuse has not blown.
The light does not come onEnsure that the bulb is correctly fitted.
Replace the bulb if it has blown.
Check the door light switch is not jammed.
The temperature in the fridge or freezer section is
too high
The freezer door will not openHas door just been opened? If so leave for a few
The compressor runs continuouslyAdjust the thermostat to give correct temperature
Check the thermostat is turned to the correct setting
relative to ambient conditions.
Check the ambient temperature is within the
appliances operating limits of 10°C to 32°C.
Relocate the appliance if necessary.
minutes to allow the air pressure to equalise.
control. See page 6.
Check that the doors are closed.
Large quantities of food have recently been placed
in the cabinet / and or door is frequently opened.
Check that air ventilation is not obstructed.
Excessive frost and ice has built upEnsure the doors are not left open.
Check that nothing is preventing the doors from
closing.
Is the door gasket intact and clean.
Noise
If after the above checks there is still a fault call your local Service Force Centre.
In-guarantee customers should ensure that the above checks have been made as the engineer will
make a charge if the fault is not a mechanical or electrical breakdown.
Please note that proof of purchase is required for in-guarantee service calls.
Refer to normal operating sounds.
13
Page 14
Service and Spare Parts
If you require service or spare parts please
contact your local Service Force Centre by
telephoning:
0990 929929
The address of your local centre can be found on
the following pages; and also in your local
telephone directory.
Before contacting your local Service Force Centre
make a note of the model and serial number,
together with date of purchase. The service
department will require this information.
The model and serial number can be found on the
rating plate situated inside the cabinet.
14
Page 15
ELECTROLUX SERVICE FORCE
To contact your local Electrolux Service Centre telephone 0990 929929
It is dangerous to alter the specifications
or attempt to modify this product in any
way.
17
Page 18
Electrical Connections
Any electrical work required to install this
appliance should be carried out by a
qualified electrician or competent person.
This appliance must be earthed.
The manufacturer declines any liability should
these safety measures not be observed.
Electrical Requirements
Before switching on, make sure the electricity
supply voltage is the same as that indicated on
the appliance rating plate.
The appliance is supplied with a 13 amp plug
fitted. In the event of having to change the fuse in
the plug supplied, a 13 amp ASTA approved
(BS1362) fuse must be used.
Should the plug need to be replaced for any
reason. The wires in the mains lead are coloured
in accordance with the following code:
Green and Yellow: Earth
Blue: Neutral
Brown: Live
The wire coloured green and yellow must be
connected to the terminal marked with the letter
"E" or by the earth symbol or coloured green
and yellow.
The wire coloured blue must be connected to the
terminal marked "N" or coloured black.
The wire coloured brown must be connected to
the terminal marked "L" or coloured red.
Upon completion there must be no cut, or stray
strands of wire present and the cord clamp must
be secure over the outer sheath.
18
Page 19
Installation Requirements
To ensure correct operation this appliance must
not be located where the temperatures will fall
below 10°C (50°F) or rise above 32°C (90°F).
Avoid the following locations: unheated kitchen,
outhouse, conservatory, garage.
For correct operation this appliance must be
installed:
In a dry atmosphere.
Out of direct sunlight.
Away from extreme temperature (not next to a
cooker or other sources of heat).
Your appliance will be heavy when loaded
with food and must therefore be stood on a
strong firm floor.
Ventilation Requirements
Gently push into place until the top panel rear
ventilation grill touches against the wall.
When in position a 50 mm (2") clear space
above the appliance should be maintained.
If space above the appliance is not available,
clearance of 25mm (1") should be maintained
on both sides.
OR
WALL
Ensure that the appliance does not stand
on the electrical supply cable.
Parts which heat up should not be
exposed. Whenever possible , the back of
the appliance should be close to a wall but
leaving the required distance for
ventilation.
Levelling
The appliance should be level, to eliminate
rocking:
Ensure the appliance is upright and both
adjusters are in firm contact with the floor so
that the cabinet is level.
Adjust the level by screwing out the
appropriate level adjuster at the front, (use
your fingers or a suitable spanner).
This appliance is heavy. Care
should be taken when moving it.
19
Page 20
Door Reversal
1. Disconnect it from the electricity supply.
2. Remove all loose items, including food. Store
food in a cool place.
3. Make sure a towel or cloth is at the base of
the product to prevent it from slipping.
4. Carefully lean the appliance backwards,
resting the top on a stool, or something
similar, at least 30cm (12") from the floor.
(care must be taken not to allow the appliance
wheels to slip).
Do not support the appliance on the rear
ventilation grille or condenser.
5. Remove level adjuster (A) from base of
product retaining small cup spacer which is
located around the threaded portion of the
adjuster.
6. Remove the foot / hinge assembly (B) by
removing screws marked (C).
7. Remove the bottom door by lifting it upwards
slightly and carefully sliding it down off the
centre hinge pin (H).
8. Remove blanking plate (M) using a flat blade
screwdriver.
9. Remove the centre hinge (H) by loosening
screw (G) and removing totally screw (J).
Remove the top door by carefully sliding it
down off the upper hinge pin (P).
10. Unscrew the upper hinge pin (P) and transfer
it to the opposite side of the cabinet.
11. Refit blanking plate (M) onto the opposite side
of the cabinet.
20
Page 21
12. Next stage is to remove the door closure
device fitted on each door handle.
Remove blanking plug (N) on each door
handle by using a flat bladed screwdriver.
Remove door closure device (R) by removing
screw (S) on both doors and fit to opposite
side of door. Note that the door closure device
is handed so when transferring it to the
opposite side the device which was on the
bottom of the top door will now be fitted to the
top of the bottom door and visa versa.
Now replace blanking plug (N) in the opposite
side of each door.
Refit the top door by carefully sliding it onto
the upper hinge pin (P).
13. Refit the top door by carefully sliding it
onto the upper hinge pin (P).
14.Turn the centre hinge (H) around from its
illustrated position and transfer it to the
opposite side. Gently press the centre hinge
up into the door being careful to retain the
door closure clip (L).
To secure the centre hinge to the cabinet,
refit screw (J). Ensure the top door is
correctly aligned before fully tightening the
screws (J) and (G). This can be achieved
by sideways movement of the centre hinge.
The base of your product should now be in
line with the diagram.
N
R
S
15. Refit the bottom door by sliding it onto
the centre hinge pin. Take the bottom
hinge foot assembly (B) and transfer
it over to the opposite side of the
cabinet being careful to retain any
spacing washer fitted onto the bottom
hinge pin. Push the hinge foot
assembly (B) into the door bearing
using the pin of the foot for location.
Three holes will then line up with the
hinge foot and screws (C) should be
used to secure the hinge. Refit level
adjuster and spacer (A) in the opposite
side of the cabinet.
16. The base of your product should now be in
line with the diagram.
17. Stand the appliance upright.
B
A
C
21
Page 22
GUARANTEE CONDITIONS
Standard guarantee conditions
We, Electrolux, undertake that if within 12 months of the date of the purchase this Electrolux appliance or any part
thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our option repair or
replace the same FREE OF CHARGE for labour, materials or carriage on condition that:
l
l
l
lll
The appliance has been correctly installed and used only on the electricity supply stated on the rating
plate.
The appliance has been used for normal domestic purposes only, and in accordance with the
manufacturer's instructions.
The appliance has not been serviced, maintained, repaired, taken apart or tampered with by any person
not authorised by us.
All service work under this guarantee must be undertaken by an Electrolux service centre.
Any appliance or defective part replaced shall become the Company's property.
This guarantee is in addition to your statutory and other legal rights.
Home visits are made between 8.30am and 5.30pm Monday to Friday. Visits may be available outside
these hours in which case a premium will be charged.
Exclusions
This guarantee does not cover:
l
l
l
l
Damage or calls resulting from transportation, improper use or neglect, the replacement of any light bulbs
or removable parts of glass or plastic.
Costs incurred for calls to put right an appliance which is improperly installed or calls to appliances outside
the United Kingdom.
Appliances found to be in use within a commercial environment, plus those which are subject to rental
agreements.
Products of Electrolux manufacture which are not marketed by Electrolux.
European Guarantee
If you should move to another country within Europe then your guarantee moves with you to your new home subject
to the following qualifications:
ll
lll
l
Before you move please contact your nearest Customer Care centre, listed below, to give them details of your new
home. They will then ensure that the local Service Organisation is aware of your move and able to look after you
and your appliances.
The guarantee starts from the date you first purchased your product.
The guarantee is for the same period and to the same extent for labour and parts as exists in the new
country of use for this brand or range of products.
This guarantee relates to you and cannot be transferred to another user.
Your new home is within the European Community (EC) or European Free Trade Area.
The product is installed and used in accordance with our instructions and is only used domestically, i.e. a
normal household.
The product is installed taking into account regulations in your new country.