Electrolux EIDW5705PB User Manual

Detergent and Rinse Aid Dispenser

The detergent and rinse aid dispenser is a one

piece component consisting of a molded

detergent cup and a built-in rinse aid dispenser.

The detergent cup has a spring loaded cover

and the rinse aid dispenser has a removable

cover.

Liquid rinse aid is added to the dispenser up to

the fill line indicator. The amount of rinse aid

released can be adjusted by turning the arrow

indicator from one, being the least amount, to

four, being the greatest amount.

To replace dispenser:

• shut off electricity to dishwasher,

• remove outer door panel assembly,

• disconnect wiring to the actuator,

• remove the six screws,

• remove the dispenser,

• replace and reinstall screws,

• rewire actuator.

wash cycle. The heater cycles ON and OFF for

Standard Dry Air Flow

The heated, moist air leaving the dishwasher

through the lower vent causes drier air to be

drawn into the unit by way of intake vents located

at the side of the tub.

The water on the dishes is evaporated into drier

air and the venting process continues. The

heating element is turned ON and OFF during the

entire drying cycle.

brief periods during the drying cycle.

Voltage checks of the heater should be made in

the dry portion of the service test mode.

is attached by a clamp to the discharge end of

the drain pump.

Heater

Refer to the cycle chart on the reverse side to

determine when the heater is on during the

Pump Assembly

The pump assembly is driven by a synchronous

motor. The motor drives a pump which supplies

100 percent filtered water

Draining is accomplished by using a small

separate synchronous drain pump mounted to

the side of the sump. The drain pump is

connected to the main pump by a small rubber

hose. The drain check valve is located at the

discharge end of the drain pump. The drain hose

The drain hose must have a loop at a

drainage.

height of 32 inches

in order to insure proper

Hi-Limit Thermostat ............... 200°F (93°C)

Total Amps (load rated) ........................... 8.7

Motor (Amps) ...................................... 1 amp

Heater Wattage .......................... 475 - 630W

Separate Circuit..15 amp min.- 20 amp max.

TempAssure .............................. 135°F ±5°F

TempBoost ................................ 140°F ±5°F

(60°C±3°C) [with outer door in place]

Heated Wash/Heated Rinse

Pressure (PSI) min./max. ................... 20/120

Connection (NPT) .....................................

Consumption (Normal Cycle) .......................

Water valve flow rate (U.S. GPM) ........... 0.9

Water recirculation rate (U.S. GPM) ..............

Water fill time ..................................... 43 sec.

................................................. approx. 5.28

............................................ 5.8-6.0 U.S. gal

minimum

Product Specifications

Electrical

Rating ...................................120 Volts, 60Hz

Water Supply

Suggested minimum incoming water

temperature ............................ 120°F (49°C)

Detergent left in dispenser.

1. Detergent allowed to stand too long in

2. Dispenser wet when detergent was

3. Detergent cover held closed or blocked

4. Improper incoming water

5. See "Detergent cover will not open." by large dishes.

temperature to properly dissolve

detergent.

added.

dispenser.

not vented.

Dishwasher water siphons out.

4. Defective float switch.

5. Electronic control board defective.

6. Wiring or terminal defective.

7. Pressure Switch Stuck.

1. Drain hose (high) loop too low.

2. Drain line connected to a floor drain

4. Repair or replace.

5. Replace control board.

6. Repair or replace.

7. Repair or replace.

1. Repair to proper

height

Dishwasher will not fill with water.

1. Water supply turned off.

2. Defective water inlet fill valve.

3. Check fill valve screen for

obstructions.

1. Turn water supply on.

2. Replace water inlet fill valve.

3. Disassemble and clean screen.

Dishwasher will not pump out.

3. Wiring or terminal defective.

4. Broken spring(s).

5. Defective actuator.

1. Drain restricted.

2. Electronic control board defective.

3. Defective drain pump.

4. Blocked impeller.

5. Open windings.

6. Wiring or terminal defective.

3. Repair or replace.

4. Replace dispenser.

5. Replace dispenser.

1. Clear restrictions.

2. Replace control board.

3. Replace pump.

4. Check for blockage, clear.

5. Replace pump assembly.

6. Repair or replace.

Motor trips out on internal thermal

Detergent cover will not latch or

open.

1. Latch mechanism defective.

2. Electronic control board defective.

1. Replace dispenser.

2. Replace control board.

Dishwasher runs but will not heat.

1. Heater element (open).

2. Electronic control board defective.

3. Wiring or terminal defective.

4. Hi-Limit thermostat defective.

1. Replace heater element.

2. Replace control board.

3. Repair or replace.

4. Replace thermostat.

overload protector.

1. Improper voltage.

2. Motor windings shorted.

3. Glass or foreign items in pump.

1. Check voltage.

2. Replace motor/impeller assembly.

3. Clean and clear blockage.

Motor hums but will not start or run.

4. No 12 VAC power to control.

5. Motor (inoperative).

6. Door switch (open contacts).

7. Door latch not making contact with

8. Touch pad circuit defective.

1. Motor (bad bearings).

2. Motor stuck due to prolonged

non-use.

1. Replace motor assembly.

2. Rotate motor impeller.

9. No indicator lamps illuminate when door switch.

START or OPTIONS are pressed.

4. Replace control board.

5. Replace motor/impeller assembly.

6. Replace latch assembly.

7. Replace latch assembly.

8. Replace console assembly.

9. Replace console assembly.

/8"

Symptom

Dishwasher will not operate when

turned on.

Always disconnect the dishwasher from the electrical power source before adjusting or

replacing components.

Check the Following

1. Fuse (blown or tripped).

2. 120 VAC supply wiring connection

3. Electronic control board defective. faulty.

Personal Injury Hazard

Remedy

1. Replace fuse or reset breaker.

2. Repair or replace wire fasteners at

3. Replace control board. dishwasher junction box.

Trouble Shooting Tips

020905

32-inch minimum

SERVICE DATA SHEET

P/N EIDW5705

Electronic Series

Color Code

BK...................... Black

BU........................ Blue

PK.........................Pink

RD..........................Red

WH/RD.........White/Red

RD-YE........Red/Yellow

VT.......................Violet

OR....................Orange

GR......................Green

W........................White

Wiring Diagram

Display Codes (LED)Display Codes (Readout)

To start

To delay start

Press START/CANCEL pad. Close and latch door.

Press DELAY START pad to select desired

delay time. Close and latch door.

To select a new

cycle or option

Press desired cycle and/or option pad. The indicator lights

will change. Press START/CANCEL within 15

seconds to begin cycle.

To cancel cycle

Press START/CANCEL. Dishwasher will drain for 60

seconds, then shut off.

For controls

lock . . . . . . . . . . .

Press and hold the AIR DRY pad for 3 seconds.

To unlock, press and hold the AIR pad for 3 seconds.DRY

CLEAN

OPTION LED's Flashing

----------------- Shows completion of cycle. Indicator light will go off 30 seconds after door

is opened.

-- HI-TEMP WASH and AIR DRY/ LED's flashing indicates power failure

has occurred. Press START/CANCEL pad and reselect desired options and

cycle.

LOW RINSE

SANITIZE

----------- The liquid rinse agent is low. Light will switch off after 5 complete

wash cycles or dispenser is filled.

--------------- The SANITIZED criteria has been met. Indicator light will go off 30 seconds

after door is opened.

This information is intended for use by persons having electrical and mechanical training and a level of knowledge of these subjects generally considered acceptable in the appliance repair trade. Electrolux Home Products North America cannot be responsible, nor assume any liability, for injury or damage of any kind arising from the use of this Service Data Sheet.

Operation

LO.

'01-24'

.........Low liquid in the rinse aid dispenser

..........A power failure has occurred

..........Close the door

....Hour(s) delay before start

The water/service test is a

Special function initiated

from the power failure

mode or idle mode.

While in power failure

or idle mode -

simultaneously press the

AIR DRY and START/CANCEL

pads for 1 1/2 seconds.

The dishwasher will then

step through the test

cycle per the chart.

Pushing the START/CANCEL

pad will advance the

dishwasher to the next step.

Water/Service Test

(Some models)

Cycle Selection Options