Electrolux EI30BM55HBC, EI30BM55HSC, EI30BM55HWC, EI30BM55HZC, EI30BM5CHBC Installation Guide

...

|NSTALLA'rioN INsrRucrIoNS

BEFORE YOU BEGIN

• _ Save these instructions for local inspector's use.

• _ Observe all governing codes and

coordinates.

• NOTE TO iNSTALLER - Be sure to leave these instructions with the Consumer.

• NOTS: TO CONSUMER - Keep these instructions for

future reference.

• SKILL LEVEL - Installation of this appliance requires

basic mechanical and electrical skills.

Readtheseinstructionscompletelyandcarefully.

1 MOUNTINGSPACE

This Over the Range Microwave Oven requires a mounting space on awall as shown in Figure 1.It is designed to be used with standard 12" wall cabinets. The maximum depth is 13".

i L

13"maxdepth.

• Proper installation is the responsibility of the installer.

• Product failure due to improper installation is not covered under the Warranty.

• Please read all instructions thoroughly before installing the Over the Range Microwave Oven. Two people are recommended to install this product.

• If a new electrical outlet is required, its installation should be completed by a qualified electrician before the Over the Range Microwave Oven is installed. See 3 ELECTRICAL GROUNDING INSTRUCTIONS on page 2.

2 WALLCONSTRUCTION

This Over the Range Microwave Oven should be mounted against and supported by a flat vertical wall. The wall must be flat for proper installation. If the wall is not flat, use spacers

to fill in the gaps. Wall construction should be a minimum of 2"x 4"wood studding and 3/8"or morethick dry wall or plaster/lath. The mounting surfaces must be capable of supporting weight of 110 pounds--the oven and contents--AND the weight of all items which would normally be stored in the top cabinet

above the unit.

30"or more

Backspiash Atleast2" from cooking

[

i i

Figure1

surface

66" or more

from floor

The unit should be attached to a minimum of one 2" x 4" wall stud.

To find the location of the studs, one ofthe following methods

may be used:

A. Use a stud finder, a magnetic device which locates the

nails inthe stud.

B. Use a hammer to tap lightly across the mounting surface

to find a solid sound. This will indicate stud location.

The center of the stud can be located by probing the wall with a small nail to find the edges of the stud and then placing a

mark halfway between the edges. The center of any adjacent

studs will normally be 16" or 24" to either side of this mark.

NEEDHELP?

For customers in the United States and Canada United States: 1-800-944-9044 Canada: 1-800-265-8352

READ CAREFULLY. KEEP THESE INSTRUCTIONS.

316902446

TIHSEB294WBRZ-EL81

PrintedinThailand

3 ELECTRICALGROUNDINGiNSTRUCTiONS 4 HOODEXHAUSTDUCT

This appliance must be grounded. This oven is equipped with a cord having a grounding wire with a grounding plug. It must be plugged into a wall receptacle that is properly installed and grounded in accordance with the National Electrical Code and

local codes and ordinances. In the event of an electrical short circuit, grounding reduces risk of electric shock by providing

an escape wire for the electric current.

WARNING - Improper use of the grounding plug can result in a risk of electric shock.

ELECTRICALREQUIREMENTS

The oven is equipped with a 3-prong grounding plug. DO NOT UNDER ANY CIRCUMSTANCES CUT OR REMOVE

THE GROUNDING PIN FROM THE PLUG.

DO NOT USE AN EXTENSION CORD. If the power supply cord is too short, have a qualified electrician or serviceman install an outlet near the appliance.

The Power Supply Cord and plug must be connected to a separate 120 Volt AC, 60 Hz, 15 Amp, or more branch circuit, single grounded receptacle. The receptacle should be located inside the cabinet directly above the Microwave Oven mounting location as shown in Figure 2.

NOTE:

1. If you have any questions about the grounding or electrical instructions, consult a qualified electrician or serviceperson.

2. Neither Electrolux nor the dealer can accept any liability for damage to the oven or personal injury resulting from failure to observe the correct electrical connection procedures.

When the hood is vented to the outside, a hood exhaust duct

is required. All ductwork must be metal; absolutely do not use

plastic duct. Check that all connections are made securely.

Please read the following carefully:

EXHAUSTCONNECTION:The hood exhaust has been designed to connect to astandard 3 V4"x 10" rectangular duct. If round duct is required, a rectangular-to-round adapter must be

used.

REAREXHAUST: If a rear or horizontal exhaust is to be used, care should be taken to align the exhaust with the space between the studs, or wall should be prepared at the time it

is constructed by leaving enough space between wall studs to accommodate exhaust.

MAXIMUM DUCT LENGTH:For satisfactory air movement, the total duct length of 31/4" x 10" rectangular or 6" diameter round

duct should not exceed 140 feet.

Elbows, adapters, wall caps, roof caps, etc. present additional

resistance to air flow and are equivalent to a section of straight duct which is longer than their actual physical size. When calculating the total length, add the equivalent lengths of all transitions and adapters plus the length of all straight duct

sections. Figure 3 shows the approximate feet of equivalent

length of some typical ductwork parts. Use the values in parentheses for calculating air flow resistance equivalent,

which should total less than 140 feet.

NOTE:

Furnace duct sealing tape is recommended to seal duct connections to the Exhaust Dampener Assembly.

Ground - [_q

Receptacle [_J

PowerCord

t Openingfor

Figure2

® 2

% o

90° Elbow(10 ft.) 45° Elbow (5 ft.) Adaptor (5 ft.)

90° Elbow (25 ft.) 45° Elbow (5 ft.) Wall cap (40 ft.) Roof cap (24 ft.)

Figure3

10"WideElbow(10ft.)

5 7 PREPARATIONOFTHEOVENTOOLSRECOMMENDEDFOR

iNSTALLATiON

= Phillips Screwdriver

• Electric Drill

® 1/2", s/8" and 3/32"Drill Bits

1 1/2"Wood Bit or Metal Hole Cutter (if metal cabinet is used)

Saw to cut exhaust opening (if needed) Protective Drop Cloth for product and range -

you may also use carton for protection

• Scissors Pencil

Measure Tape

6 INSTALLATIONHARDWARE

The INSTALLATION HARDWARE items (_ - @ are in a small bag. All items are in a bag packed below the oven.

Item Name Quantity

Wood Screw 5 x 35 mm 6 Toggle Bolt 3/16" 4

G Top Cabinet Screw 5 x 93 mm 2

Flat Washer 30 mm diameter 2 @ Grommet 1 ® Tapping Screw4 x 8 mm 4

Exhaust Damper Assembly 1 ® Grease Filter 2

® Rear Cushion 1 ® Installation Instructions 316902446 1

® Top Template 316902447 1 @ Wall Template 316902448 1

Open the bottom of the carton, bend the carton flaps back and tilt the oven over to rest on plastic foam pad.

Lift carton off oven and remove all packing materials, Installation Instructions, Wall Template, Top Template,

Turntable and Turntable Support; however, DO NOT

REMOVE THE WAVEGUIDE COVER, which is located

on the ceiling in the oven cavity. SAVE THE CARTON AS

IT MAY MAKE INSTALLATION EASIER.

2. CHECK THE OVEN. Check the oven for any damage, such as misaligned or

bent door, damaged door seals and sealing surfaces, broken or loose door hinges and latches and dents inside the cavity or on the door. If there is any damage, do not operate the oven and contact your dealer or Electrolux

AUTHORIZED SERVICER.

Mounting Plate

Figure5

k!J

k7_J

k6P_ .....

Figure 4

Partsshownnottocommonscale.

3 ®

8 VENTiLATiONSYSTEM

(PREPARINGOVENFOBiNSTALLATiON)

This Over the Range Microwave Oven is designed for adaptation to three types of hood ventilation systems. Select the type required for your installation.

RECIRCULATING-- non-vented, ductless. Follow installation procedure (A). Recirculating requires the use of the Charcoal Filters, which have already been installed in

the oven. HORIZONTAL EXHAUST -- outside ventilation. Follow

installation procedure (B). VERTICAL EXHAUST -- outside ventilation. Follow

installation procedure (C).

(A) RECIBCULATING: NON-VENTED,DUCTLESSOPERATION

The unit is shipped assembled for recirculating.

NOTE:

1. The Exhaust Damper Assembly is not required for recirculating exhaust.

2. The Charcoal Filters should be replaced every 6 to 12 months, depending on use.

OvenLightCover

OvenLight

HORIZONTAL EXHAUST: OUTSIDEVENTILATION

(B)

Remove 3 screws from back edge and 5 screws from the top of Fan Cover Bracket. Save 3 screws to use them to attach Exhaust Damper Assembly to the wall later and discard remaining 5. Remove Fan Cover Bracket by

sliding it in the opposite direction of the arrow on the Fan Cover Bracket, as shown in Figure 7.

Lift Hood Fan Unit carefully and slip wires out of cavity. See Figure 8. CAUTION: Do net pull or stretch Hood Fan

Wire.

3. Rotate the Hood Fan Unit 180 ° so that the Fan Blade Openings are facing the back of the oven. See Figure 9A on

page 5.

4. Replace Hood Fan Wire from (A) to (B). See Figure 9B on page 5. Replace Hood Fan Unit into the oven. Be

careful not to pinch the Hood Fan Wire and the Hood

Fan Unit. See Figure 9C on page 5.

5. Put the wire back into cavity. See Figure 10A on page 5.

6. Assemble the Exhaust Damper Assembly to the Fan Cover Bracket by sliding it into the slits in the same

direction as the arrow. Use 1 Tapping Screw 4 x 8 mm from the INSTALLATION HARDWARE and tighten into place. See Figure 10B on page 5.

7. This assembly will be mounted to the Outside Rear

Exhaust cutout in future instructions. See WALL

TEMPLATE for further procedures.

HoodLouver

HoodLouver(Inside)

FigureGA

Upper Tab

HoodFanWire

FanCover Bracket

FiguPe7

HoodFanUnit

/ / /

® 4

FiguPeGg

Figupe8

Rotate

Changethe position of wire to left side hole

FanW=re _

_-_, _

1800

_ FanBladeOpenings

(B) (A)

Figure 9B

(c)

4. Replace the Fan Cover Bracket by sliding it into the slits in

5. Attach the Fan Cover Bracket to unit with the 3 screws

6. Attach the Exhaust DamperAssembly to the fan cover bracket

iii,i,i,i

VERTICALEXHAUST:OUTSIDEVENTiLATiON

Remove and save 3 screws from back edge and 5 screws

from the top of the Fan Cover Bracket to use at Step 5.

Remove Fan Cover Bracket by sliding it in the opposite

direction of the arrow on the Fan Cover Bracket as shown in

Figure 11. Lift Hood Fan Unit carefully and slip wires out of cavity. See

Figure 12A. CAUTION: Do not pull or stretch Hood Fan Wire. Rotate the Hood Fan Unit 180 ° so that the Fan Blade

Openings are facing the back of the oven. See Figure 12B on page 6. Replace Hood Fan Wire from (A) to (B). See

Figure12C on page 6. Then rotate the Hood Fan Unit 90 ° so that the Fan Blade Openings are facing the top of the oven. See Figure 13 on page 6. Replace Hood Fan Unit into the oven. Be careful not to pinch the lead wire between the

inner bracket and the Hood Fan Unit. Put the lead wire into Wire Box.

the same direction as the arrow on the Fan Cover Bracket.

Make sure the fan blades are visible through the top openings in the oven before proceeding. See Figure 14 on

page 6.

from back edge and 4 screws except screw(A) from the top of the Fan Cover Bracket, which were removed at Step 1

above. See Figure 14 on page 6. Screw (A) will be used at

MOUNTING OVEN THE WALL Step5 on page 7. The Hood

Fan Unit is now rotated for vertical exhaust operation.

on the top of the outercase cabinet after mounting the oven. To attach the Exhaust Damper Assembly, refer to MOUNTING

OVEN TO THE WALL, See Figure 20 on page 7 and TOP CABIN ET TEM PLATE.

Exhaust Dam

Assembly

FanCoverBracket

Savethe assemblyfor

future instructions.

I Oven Rear Side I

"_ _1 I Wall Side I

nlFJ_ __ .......................RearCushion

0 0 l --

, earOushio

!71I after ExhaustDamper

....... Assemblyis screwed

towall.

Figure lOB

(A)

FanCoverBracket

Figure11

Rotate180° _ FanBiade Openings

Changethe positionof wiretoleftside hole

(A) Rotate900

i i

(B) (A)

Figure12C

{B)

FanBladeOpenings

NOTE:THISOVENSHOULDBEATTACHEDTOATLEASTONEWALLSTUD.

MOUNTING PLATE

1. Separate Toggle Nuts, packed in the INSTALLATION HARDWARE, from 4 Toggle Bolts.

2. _ Use the mounting template provided

to Use wood screws to attach mounting plate to the stud or studs. Use Toggle Bolts to attach mounting plate through the holes at A, B, C and D UNLESS

THOSE HOLES ARE LOCATED ON THE STUD. insert one Toggle Bolt into A, B, C and D where appropriate

(these correspond to holes of the Wail Template) and put the Toggle Nuts onto the Toggle Bolts. See Figure

15. Refer to instructions in Wail Template.

/ /

A C D B

Position the Mounting Plate with the Toggle Bolts attached

at the wall location and insert Toggle Nuts and Bolts through the holes in the wall with the Toggle Nuts closed. See Figure

16. Use Wood Screws to attach the Mounting Plate to

studs. NOTE: Before insertion, be sure you leave a space more than

the thickness of the wall between the Mounting Plate and the end of each of the Toggle Nuts (in the closed position).

If you do not leave enough space, the Toggle Nut will not

be able to open on the other side of the wall. Also, once a Toggle Nut opens, it cannot be withdrawn from the hole; therefore make sure all of the Toggles are in the correct position before insertion.

Align the Mounting Plate carefully and hold in position while tightening Toggle Bolts. Pull Toggle Bolt toward

you and turn clockwise to tighten. See Figure 17.

OVEN INSTALLATION

THIS OVEN CANNOT BE PROPERLYINSTALLED WITHOUT REFERRING TOTHEMOUNTINGINSTRUCTIONSFOUNDONBOTHTEMPLATES.

THE NEXT STEP IS TO READ AND FOLLOW MOUNTING INFORMATION ON BOTHTOPCABINETAND WALLTEMPLATES.

Figure 14

ToggleBolt

Mounting Plate

, _ bpace more

i i

' thickness

Figure15

,_ than wail

,,%.

i /

MOUNTINGOVENTOTHEWALL

Two people are recommended to attach the Microwave Oven/ Hood to the Mounting Plate.

1. Thread the power supply cord through the hole made in the bottom of the top cabinet.

2. Install the oven by tilting it forward and sliding it onto two tabs of the Mounting Plate. Rotate the oven up so it rests

against the wall. See Figure 18 on page 7.

3. Use the two Top Cabinet Screws and two Flat Washers, supplied in the INSTALLATION HARDWARE, to attach the

unit to the top cabinet. See Figure 19 on page 7.

4. Secure the bottom of the oven to the Mounting Plate by using two Tapping Screws 4 x 8 mm from the INSTALLATION

HARDWARE. See Figure 19 on page 7.

5. (For Vertical Exhaust Only) Attach the Exhaust Damper Assembly to the fan Cover

Bracket on the top of the outercase cabinet by sliding it into the slits in the same direction as the allow using screw (A)

which removed at (C) VERTICAL EXHAUST STEP 1 on page 5. See Figure 20 on page 7.

Tapping Screw (A)

Figure20

CHECKLISTFORINSTALLATION

1. Make sure the unit has been installed according to all of the Installation Instructions and the Wall and Top Cabinet Templates.

2. Plug in the power cord.

3. Keep these Installation Instructions.

Figure18

Tabs

NOTE: Make sure to remove the tape at the turntable support before

operation. See figure 21.

Removethis tapebefore operation.

Figure21

Tapping Screws

Figure 19 7

+ 16 hidden pages