Electrolux EI30BM55HBB, EI30BM55HSB, EI30BM55HWB, EI30BM55HZB, EI30BM5CHBB Installation Guide

...

verThe

ange

BEFORE YOU BEGIN

• _ Save these instructions for local inspector's use.

• _ Observe all governing codes and

coordinates.

• NOTE TO INSTALLER - Besureto leavethese instructions with the Consumer.

• NOTE TO CONSUMER - Keep these instructions for

future reference.

• SKILL LEVEl. - Installation of this appliance requires basic mechanical and electrical skills.

Read theseinstructions completely and carefully.

1 MOUNTINGSPACE

This Over the Range Microwave Oven requires a mounting space on a wall as shown in Figure 1. Itis designed to be used with standard 12" walt cabinets.

icrowave

Proper installation is the responsibility of the installer. Product failure due to improper installation is not covered

under the Warranty. Please read all instructions thoroughly before installing

the Over the Range Microwave Oven. Two people are

recommended to install this product. If a new electrical outlet is required, its installation should

be completed by a qualified electrician before the Over the Range Microwave Oven is installed. See 3 ELECTRICAL GROUNDING INSTRUCTIONS on page 2.

Oven

2 WALLCONSTRUCTION

This Over the Range Microwave Oven should be mounted against and supported by a flat vertical walt. The wall must be flat for proper installation. Ifthe wall is not flat, use spacers to fill in the gaps. Wall construction should be a minimum of 2" x 4" wood studding and 3/8"or more thick dry wall or plaster/lath. The mounting surfaces must be capable of supporting weight

of 110 pounds--the oven and contents--AND the weight of all items which would normally be stored in the top cabinet

above the unit.

...................i

__i

30" or more

fromcooking

surface

66" or more

fromfloor

The unit should be attached to a minimum of one 2" x 4" wall stud.

Tofind the location of the studs, one of the following methods may be used:

A. Use a stud finder, a magnetic device which locates the

nails in the stud.

B. Use a hammer to tap lightly across the mounting surface

to find a solid sound. This will indicate stud location.

The center of the stud can be located by probing the wall with a small nail to find the edges of the stud and then placing a mark halfway between the edges. The center of any adjacent studs will normally be 16" or 24" to either side of this mark.

NEEDHELP?

For toll-free telephone support in the U.S. and Canada:

1-877-4ELECTROLUX (1-877-435-3287)

READ CAREFULLY. KEEP THESE INSTRUCTIONS.

P/H316495050

TIlISEB177WRRZ-EL81

PrintedinThailand

Installation instructions

3 ELECTRICALGROUNDINGINSTRUCTIONS

This appliance must be grounded. This oven is equipped with a cord having a grounding wire with a grounding plug. It must

be plugged into a wall receptacle that is properly installed and grounded in accordance with the National Electrical Code and

Iocai codes and ordinances. Inthe event of an electrical short circuit, grounding reduces risk of electric shock by providing

an escape wire for the electric current. WARNING - Improper use of the grounding plug can result in

a risk of electric shock.

ELECTRICALREQUIREMENTS

The oven is equipped with a 3-prong grounding plug. DO NOT UNDER ANY CIRCUMSTANCES CUT OR REMOVE THE GROUNDING PiN FROM THE PLUG.

DO NOT USE AN EXTENSION CORD. If the power supply cord is too short, have a qualified electrician or serviceman

install an outlet near the appliance.

The Power Supply Cord and plug must be connected to a separate 120 Volt AC, 60 Hz, 15 Amp, or more branch

circuit, single grounded receptacle. The receptacle should be located inside the cabinet directly above the Microwave Oven mounting location as shown in Figure 2.

NOTE:

1. If you have any questions about the grounding or electrical instructions, consult a qualified electrician or

serviceperson.

2. Neither Electrolux nor the deater can accept any liability for damage to the oven or personat injury resulting from failure

to observe the correct electrical connection procedures.

4 HOODEXHAUSTDUCT

When the hood isvented to the outside, a hood exhaust duct

is required. All ductwork must be metal; absolutely do not use plastic duct. Check that all connections are made securely.

Please read the following carefully:

EXHAUSTCONNECTION:The hood exhaust has been designed to connect to a standard 3 1/4"x 10" rectangular duct. If round duct is required, a rectangular-to-round adapter must be

used.

REAREXHAUST: If a rear or horizontal exhaust is to be used, care should be taken to align the exhaust with the space

between the studs, or wail should be prepared at the time it

is constructed by leaving enough space between watt studs to accommodate exhaust.

MAXIMUM DUCTLENGTH:For satisfactory air movement, the total duct length of 31/4" x 10" rectangular or 6" diameter round

duct should not exceed 140 feet.

Elbows, adapters, wall caps, roof caps, etc. present additional

resistance to air flow and are equivalent to a section of straight duct which is longer than their actual physical size. When calculating the total length, add the equivalent lengths of all transitions and adapters plus the length of all straight duct

sections. Figure 3 shows the approximate feet of equivalent

length of some typical ductwork parts. Use the values in

parentheses for calculating air flow resistance equivalent, which should total less than 140 feet.

Ground F_q

Receptacle [_

PowerCord

Openingfor

Figure2

® 2

90° Elbow(10ft.)

90° Elbow(25ft.)

45° Elbow(5ft.)

Adaptor (5 ft.)

Wallcap (40 ft.)

Figure3

10"WideElbow(10ft.)

Roof cap (24 ft.)

Installation instructions

5 TOOLSRECOMMENDEDFOR

iNSTALLATiON

Phillips Screwdriver Electric Drill

1/2", 5/8" and 3/32" Drill Bits

1 1/2"Wood Bit or Metal Hole Cutter

(if metal cabinet is used) Saw to cut exhaust opening (if needed)

Protective Drop Cloth for product and range - you may also use carton for protection

Scissors Pencil

Measure Tape

6 iNSTALLATiONHARDWARE

The INSTALLATION HARDWARE items (_ - @ are in a small bag. All items are in a bag packed below the oven.

Item Name Quantity

,_0 Wood Screw 5 x 35 mm 6 (27 Toggle Bolt 3/16" 4

,_3_ Top Cabinet Screw 5 x 85 mm 2 ,_4_ Flat Washer 30 mm diameter 2

,_5) Grommet 1 ,%' Tapping Screw 4 x 8 mm 3

,_7_ Exhaust Damper Assembly 1 ,_s; Grease Filter 2

,_9_, Rear Cushion 1

7 PREPARATIONOFTHEOVEN

Open the bottom of the carton, bend the carton flaps back and tilt the oven over to rest on plastic foam pad.

Lift carton off oven and remove all packing materials, Installation Instructions, Wall Template, Top Template,

Turntable and Turntable Support; however, DO NOT

REMOVE THE WAVEGUIDE COVER, which is located

on the ceiling in the oven cavity. SAVE THE CARTON AS

IT MAY MAKE INSTALLATION EASIER.

2. CHECKTHE OVEN. Check the oven for any damage, such as misaligned or

bent door, damaged door seals and sealing surfaces, broken or loose door hinges and latches and dents inside

the cavity or on the door. If there is any damage, do not operate the oven and contact your dealer or Electrotux

AUTHORIZED SERVICER.

......... _,_._................ _-_

_; MountingPlate

Figure5

i\ 19

,;d' ["q ,_=.

_[' Usewithmetalcabinets.Surround

tYS_I_ii. thepowercordopening.Cuttofit.

Figure4

Partsshownnottocommonscale,

3 ®

Installation instructions

8 VENTiLATiONSYSTEM

(PREPARINGOVENFOBiNSTALLATiON)

This Over the Range Microwave Oven is designed for adaptation to three types of hood ventilation systems. Select

the type required for your installation.

RECIRCULATING-- non-vented, ductless. Follow installation procedure (A). Recirculating requires the use of the Charcoal Filters, which have already been installed in

the oven. HORIZONTAL EXHAUST -- outside ventilation. Follow

installation procedure (B). VERTICAL EXHAUST -- outside ventilation. Follow installation procedure (C).

(A) RECIBCULATING: NON-VENTED,DUCTLESSOPERATION

The unit is shipped assembled for recircutating.

NOTE:

1. The Exhaust Damper Assembly is not required for recircutating exhaust.

2. The Charcoal Filters should be replaced every 6 to 12 months, depending on use.

OvenLightCover

OvenLight

HORIZONTALEXHAUST:OUTSIDEVENTILATION

(B)

Remove 3 screws from back edge and 3 screws from the

top center of Fan Cover Bracket. Save 3 screws to be

used later and discard remaining 3. Remove Fan Cover Bracket by sliding it in the opposite direction of the arrow

on the Fan Cover Bracket, as shown in Figure 7.

Lift Hood Fan Unit carefully and slip wires out of cavity. See Figure 8. CAUTION:Donetpull or stretch Hood Fan

Wire.

Rotate the Hood Fan Unit 180° so that the Fan Blade Openings are facing the back of the oven. See Figure 9A on

page 5.

Replace Hood Fan Wire from (A) to (B). See Figure 9B on page 5. Replace Hood Fan Unit into the oven. Be careful not to pinch the Hood Fan Wire and the Hood

Fan Unit. See Figure 9C on page 5.

Put the wire back into cavity. See Figure 10A on page 5.

Assemble the Exhaust Damper Assembly to the Fan

Cover Bracket by sliding it into the slits in the same direction as the arrow. Use 1 Tapping Screw 4 x 8 mm from the INSTALLATION HARDWARE and tighten into

place. See Figure 10B on page 5.

This assembly wilt be mounted to the Outside Rear

Exhaust cutout in future instructions.

HoodLouver

UpperTab

FigureGA

Hood Louver(inside)

Tabs

Figure8B

® 4

Figure7

i'/ i

Figure8

Installation instructions

Rotate180°

_/_ FanBladeOpenings

Changethepositionofwiretoleftsidehole

(B) (A)

HoodFanWire

VERTICAL EXHAUST: OUTSIDEVENTiLATiON

(c)

Remove and save 3 screws from back edge and 3 screws from the top center of the Fan Cover Bracket. Remove

Fan Cover Bracket by sliding it in the opposite direction of the arrow on the Fan Cover Bracket as shown in

Figure 11.

Lift Hood Fan Unit carefully and slip wires out of cavity.

See Figure 12. CAUTION:Donotpullor stretch HoodFan Wire.

Rotate the Hood Fan Unit 90° so that the Fan Blade

Openings are facing the top of the oven. See Figure 13

(A) on page 6. Replace Hood Fan Unit into the oven.

Be careful not to pinch the lead wire between the inner

bracket and the Hood Fan Unit. Put the lead wire into Wire Box. See Figure 13 (B) on page 6.

Replace the Fan Cover Bracket by sliding it into the slits

in the same direction as the arrow on the Fan Cover

Bracket. Make sure the fan blades are visible through the top openings in the oven before proceeding.

Attach the Fan Cover Bracket to unit with the 3 screws from back edge and 3 screws from the top center of

the Fan Cover Bracket, which were removed in Step 1 above. See Figure 14 on page 6. The Hood Fan Unit is

now rotated for vertical exhaust operation.

Attach the Exhaust Damper Assembly to the fan cover

bracket on the top of the outercase cabinet after mounting the oven. To attach the Exhaust Damper Assembly, refer to MOUNTING OVEN TO THE WALL, See Figure 20 on

page 7.

Exhaust Damper

Assembly

FanCoverBracket _ .--J

Apply RearCushion

after Exhaust Damper

Assemblyisscrewed

to wall.

Savetheassembly for

future instructions,

Figure 11

-:; HoodFanUnit

HoodFanWire ....

/ // '

RearCushion

iiiiiii'ii_ Jiiii /"

Figure12

FigurelOB

5 ®

Installation instructions

{B)

i L

,S i

, j' j

, ,'

Figure13

Position the Mounting Plate with the Toggle Bolts attached at the wall location and insert Toggle Nuts and

Bolts through the holes in the wall with the Toggle Nuts closed. See Figure 16. Use Wood Screws to attach the

Mounting Plate to studs.

NOTE:Before insertion, be sure you leave a space more than the thickness of the wall between the Mounting Plate and the end of each of the Toggle Nuts (in the closed

position). If you do not leave enough space, the Toggle

Nut will not be able to open on the other side of the wall. Also, once a Toggle Nut opens, it cannot be withdrawn

from the hole; therefore make sure all of the Toggles are

in the correct position before insertion.

Align the Mounting Plate carefully and hold in position while tightening Toggle Bolts. Pull Toggle Bolt toward

you and turn clockwise to tighten. See Figure 17.

ToggleBolt

Figure14

9 OVENINSTALLATION

THISOVENCANNOTBEPROPERLYINSTALLEDWITHOUTREFERRING TOTHEMOUNTINGINSTRUCTIONSFOUNDONBOTHTEMPLATES.

THENEXTSTEPISTOREADANDFOLLOWMOUNTINGINFORMATION ONBOTHTOPCABINETANDWALLTEMPLATES.

NOTE:THISOVENSHOULDBEATTACHEDTOATLEASTONEWALL STUD.

MOUNTINGPLATE

1. Separate Toggle Nuts, packed in the INSTALLATION HARDWARE, from 4 Toggle Bolts.

2. _ Use the mounting template

provided to Use wood screws to attach mounting plate to the stud or studs. Use Toggle Bolts to

attach mounting plate through the holes at A, B, C and D UNLESS THOSE HOLES ARE LOCATED ON

THE STUD. insert one Toggle Bolt into A, B, C and D where appropriate (these correspond to holes of the Wall Template) and put the Toggle Nuts onto the

Toggle Bolts. See Figure 15. Refer to instructions in

Wall Template.

® 6

MountingPlate

' , Space more

i i

iiii I

I x

iiiiii!;i, 4_ '

.... 1/

iiiilililili_!i_

_ Wall

FiguPe18

MOUNTINGOVENTOTHEWALL

Two people are recommended to attach the Microwave Oven/

Hood to the Mounting Plate.

1. Thread the power supply cord through the hole made in the bottom of the top cabinet.

2. Install the oven by tilting it forward and sliding it onto two tabs of the Mounting Plate. Rotate the oven up so it rests

against the wall. See Figure 18 on page 7.

3. Use the two Top Cabinet Screws and two Flat Washers,

supplied in the INSTALLATION HARDWARE, to attach

the unit to the top cabinet. See Figure 19 on page 7.

4. Secure the bottom of the oven to the Mounting Plate

by using two Tapping Screws 4 x 8 mm from the INSTALLATION HARDWARE. See Figure 19 on page 7.

FiguPe15

thickness

thanwall

Figure17

Figure18

TopCabinetScrews

Installation instructions

CHECKLISTFORiNSTALLATiON

1. Make sure the unit has been installed according to atl of the Installation Instructions and the Wall and Top Cabinet Templates.

2. Plug in the power cord.

3. Keep these Installation Instructions.

Tabs

TappingScrews

Figure19

Figure20

TappingScrew

7 ®

+ 14 hidden pages