Electrolux EI23BC80KS4A, EI28BS80KS4A, EI28BS80KS7A, EI23BC80KS8A, EI23BC80KS7A Owner’s Manual
...
EN FREEZER / REFRIGERATOR USE AND CARE GUIDE
................................... FR REFRIGERATEUR/CQNGELATEUR GUIDE D:UTILISATION ETD:ENTRETIEN
:i:i:iiiiiiiii iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
_i:_i_ii_i_!_!_i@!_!:ii!_!:ii!_!_!ii_!_ii_i!_!!_!i_ii_i!ii_iii@_i_i_i_iii_ii
Finding information
Please read and save this guide Tabmeof contents
Thank you forchoos ng E ectro ux our new prem um Fin in Inf rm i n 2
brand in home appliances.This Use & Care Guide is
part of our comm tment to customer sat sfact on and f
product qualitythroughoutthe service life of your new
appliance. FeatureOverview................................................. 5
[J g 0 at 0 ..............................................
Sa ety ............................................................... 3
Keep a record for quick Installation ......................................................... 6
reference
::::::::, : Removingthe Doors ............................................ 11
^ nn "in "h W" r^ I 14
_o ecl gl e ale _uppy ..................................
__ controls..........................................................._
Electroluxmodel number
A.tornatieleelVlaker............................................ 17
___ StorageFeatures ................................................ 18
St0,.gF00_._S_,_.gE.0,gv..............................23
..........................
Changingthe Water andAir Filters........................... 25
24
i!_!_i!i_ii_!i!_!_i!i_ii_!i!_!_i!i_ii_!i!_!_i!i_ii_!i!_!_i!i_ii_!i!_!_i!i_ii_!i!_!_i!i_ii_!i!_!_i@ii_i
Westronglyencourageresponsibleappliancerecycling/
Safety
Emectricaminformation
• The refrigerator must be plugged into its own
dedicated 115 Volt, 60 Hz, AC-only non-GFCl
electric outlet. The power cord of the appliance is
equipped with a three-prong grounding plug for your
protection against electrical shock hazards. It must
be plugged directly into a properly grounded three-
prong receptacle. The receptacle must be installed
in accordance with local codes and ordinances.
Consult a qualified electrician. Do not use an
extension cord or adapter plug.
= If the power cord is damaged, it should be replaced
by the manufacturer, service technician, or a
qualified person.
= Never unplug the refrigerator by pulling on the power
cord. Always grip the plug firmly and pull straightout
from the receptacleto prevent damaging the power cord.
To avoid electrical shock, unplug the refrigerator
before cleaning and before replacing a light bulb or
LED light.
Performance may be affected ifthe voltage varies
by 10% or more. Operating the refrigerator with
insufficient power can damage the compressor.
Such damage is not covered under your warranty.
Do not plug the unit into an outlet controlled by a
wall switch or pull cord to prevent the refrigerator
from being turned off accidentally.
Grounding type wall receptacle
SDo not, under any"_
f ._i_. [ .,_ circumstances, [
1 i!_ [_ll_ bypass the |
3-'prong grounded plug _I_
_cut, remove, or |
T, turn _ _er _ur r_frige_r, unplug t"e
p )_er c_a f_ the_ll _Ut!_
Luxury-Glide TM
Crisper
Luxury-Glide TM
Crisper
i_i!_!_i!i_ii_!i!_!_i!i_ii_!i!_!_i!i_ii_!i!_!_i!i_ii_!i!_!_i!i_ii_!i!_!_i!i_ii_!i!_!_i!i_ii_!i!_!_i!i_i@:_
Installation
Required Tools
You wiii need the following tools:
Components Provided:
Top Hinge Top Hinge
Cover Front Cover Rear
Screw _ _crew
Hinge Hinge _
__ Top Lower
Screw Screw _
Tooms Necessary:
Phillips TM
Head or
#2 Square Drive
Head
OR
Socket
Wrench Set
3/8" Fixed
Wrench
This Use & Care Guide provides general installation
and operating instructions for your model. We
recommend using a service or kitchen contracting
professional to install your refrigerator. Use the
refrigerator only as instructed in this Use & Care
Guide. Before starting the refrigerator, follow these
important first steps.
Allow the following clearances for ease of installation,
proper air circulation, and plumbing and electrical
connections:
Sides & Top 3/8inch (9.5 mm)
Back 1 inch (25.4 mm)
* Choose a place that is near a grounded, non-GFCl,
electrical outlet. Do Not use an extension cord or an
adapter plug.
* if possible, place the refrigerator out of direct ..............................................................................................................................................................................................................................................................................................
sunlight and away from the range, dishwasher, or D_r nn_nine
other heat sources. _ _r_
The refr gerator must be nsta ed on a f oor that s :_.....................................................
level and strong enough to support a fully loaded
refrigerator.
, _emsel_e_ _J_ln a 28 degree eRea_a8
Consider water supply availability for models
equipped with an automatic ice maker. Your refrigerator should be positioned to allow easy
[ : access to a counter when removing food. For best
} use of refrigerator drawers and freezer baskets, the
refrigerator should be in a position where both can be
E fu y opened
i
r_ i_NNr.)) ) ) ) ) ) ) ) ) )
Installation
Freezer Drawer Amignment
(if necessary)
1 Check gasket seal around top, bottom, and sides
of freezer drawer.
2 If gasket is not sealed, open drawer and slightly
loosen four drawer screws (two on each side) to
allow drawer to rotate.
3 Close drawer and recheck the seal on the gasket
(A). Open the drawer grabbing by the sides in the
center (B). Be careful not to rotate the drawer.
Remove H ex
: Head Drawer
Screw:
Remove Remove
Hex Head
Drawer Drawer
Screw Screw
4 Tighten four drawer screws.
5 Recheck gasket seal.
To level the cabinet using the front rollers:
1 Slightly open freezer drawer. Lift the toe grille and
gently pull forward (see illustration).
2 You can raise or lower each door. Use a 3/sinch
socket wrench to turn the adjustment screws
(1 per side).
Toe Grille Must _
• " _1
Ft nSoton / I_',7.
Antiitip Bracket (_. _"
\_Z_ 12" Assembly _J,_ BY
______'_---- (3) Retaining Clips
To raise: turn adjustment screw clockwise.
To lower: turn adjustment screw
counterclockwise.
Ensure both doors are bind-free with their seals
touching the cabinet on all four sides and that
cabinet is stable.
4 After unit is leveled, lower anti-tip leg until it
contacts the floor.
Against , ,, ,,
Freezer : o :
Drawer
_" / /
o_ _ o_ _
b h
Cabinet Leve_in 9 & Refrigerator I
DOOr Amignment (if necessary)
Guidelines for final positioning of your refrigerator" :: , :: : :::::::::
All four corners of the cabinet must rest firmly on the _ ,j
f oor
= The sides should tilt 1/4inch (6 mm)from front to _ (/,O '_ /y'_
back (to ensure that doors c ose and sea proper y) I Anti-tip _'q /,/
• Doors should align with each other and be level. _/_!\ I
Most of these conditions can be met by raising or _
lowering the adjustable front rollers.
Leg /i
g. y..g. p .
Installation
To adjust the door stop:
Door stop is adjustable between 85 to 145 degrees.
Adjustable Door Stop
1 Open door to provide access to screw.
2 Loosen screw.
i!_!_i!i_ii_!i!_!_i!i_ii_!i!_!_i!i_ii_!i!_!_i!i_ii_!i!_!_i!i_ii_!i!_!_i!i_ii_!i!_!_i!i_ii_!i!_!_i!i_ii_!i!_!_i!i_ii_!i!_!_ii_i
3 Adjust door to desired location.
5 Retighten screw.
Stoic
6 Ensure door stops in desired locationbefore
resuming normal use.
To level the doors using the adjustable lower hinge
(select models):
1 Remove all food itemsfrom door bins on door
being adjusted.
2 Open doors to 90 degrees.
3 Loosen or remove screw.
Re-tighten
Screw
i!_!_i!i_ii_!i!_!_i!i_ii_!i!_!_i!i_ii_!i!_!_i!i_ii_!i!_!_i!i_ii_!i!_!_i!i_ii_!i!_!_i!i_ii_!i!_!_i!i_ii_!i!_!_i!i_ii_!i!_!_ii_i
Installation
4 Lift the door while adjusting the washer. To raise To adjust the flipper mullion:
!he door, rotate washer clockwise !when viewed 1 Loosen the screw located on the flipper mullion
from [ne bottom), io lower aoor ro[ate wasner hin-e
counterc!ockwlse (when wewed from the bottom).
_oOr ..
Door
in e _....... ..
Ro_s_°g/Lowo.°gDoor II II I | I
s Ret_ghtenthescrew,whereapplicable,ensuring ....
t s between the spokes of the set washer Screw ........
..... . ........ ' . . 2 AdjustTppermu onneght For proper
will not De tight, just insert untHit is nusn with the ....... :_. :....^ ,,:.... _., ,..... :.,^ ._.^.^
_, £;UIIII_L;I.IUII VVlLII tilt:# lll_|Jlc:_i IIIUlIIUII yUlUt:# I.II_I_
n nge
" should be a separation about the thickness of a
Re-tighten Screw and flipper mullion.
y .
Flipper
.. Screw
Mullion---] II I |_ I
II I I
Adjusting Fhpper MulhonScrew
coin(o.oooinches,or_.5mm)betweentheguide
iiiiiiiiii!;ili_i_ili'iii_i¸i_i_i_i_!i_!i_!i_!i_!i_!_i_i!i_!_!!!_i!i!i_i_i_i_!_!_!_!i!i_ii_ii_i_ii_i_!_!!i_!_!_i_ii!_i_i_iiii!_!i_i;_
Installation
Installing Shelves
Your refrigerator was shipped with the shelf hanger
and shelf lockingdip installedin their shipping position.
Below are the instructionsto installthe shelves in your
desired locations.
1 Remove shelf from itslocked position by pulling
the slide mechanism toward you.
Relock shelf by pushing the slide mechanism
away from you.
While holding shelf at a 45-degree angle with the
gray handle facing you, push the shelf intothe
back of the hanger.
i!_!_i!i_ii_!i!_!_i!i_ii_!i!_!_i!i_ii_!i!_!_i!i_ii_!i!_!_i!i_ii_!i!_!_i!i_ii_!i!_!_i!i_ii_!i!_!_i!i_ii_!i!_!_i!i_ii_!i!_!_ii_i
2 Lift the hanger directly upwards and pull toward
i!_!_i!i_ii_!i!_!_i!i_ii_!i!_!_i!i_ii_!i!_!_i!i_ii_!i!_!_i!i_ii_!i!_!_i!i_ii_!i!_!_i!i_ii_!i!_!_i!i_ii_!i!_!_i!i_ii_!i!_!_ii_i
Removing the Doors
Getting through narrow spaces
If your refrigerator will not fit through an entrance area,
you can remove the doors. Check first by measuring the
entrance.
To prepare for removing the doors:
1 Make sure the electrical power cord is unplugged
from the wall outlet.
2 Open the freezer drawer and remove the toe
grille (see "installation" section).
3 Remove any food from the door shelves and
close the doors.
To remove the refrigerator doors:
1 Trace lightlyaround the door's top hinges with a
pencil. This makes reinstallation easier.
Front
, Rear
Top Hinge
Cover \
To reinstall the right door, reverse the above steps.
Lower Hinge Removal
Once both doors are in place, ensure they are aligned
with each other and level (please see the "Installation"
section for more details), and replace the top hinge
cover.
Removing Freezer Drawer
Hinge. Ground 1 Open freezer drawer.
Screws
• . // 2 Remove drawer screws on right and left sides
{,woscrewsooeochs "e/
Hinge /-
Leave _ Remove Hex !_,_.,-'/_ _%_-__,j_w F_emove Hex
,. _/ Head Drawer /_h_//_ _'_JF.. Head Drawer
Hi.nge/ ° Screw /_/'_ _'_-_,_--_ Screw ,
vvl[n "_ _ A_.._ _#_./__ __ Im...,_ I
| _ _ .... /I_Do Not_- o '--Remcve__l_
2 Disconnect the harness by grasping both sides of I Hlli;
the connector firmly, depress the latch, and pull __ _tHIIll Remove
apart. Remove the two screws from the top hinge. _'_ HexwHea€
• . • Drawer urawer
L ft the door off of the bottom h nge and set t Screw Screw
aside.
• Hex Head Hex Head
_ 3 Lift drawer up and out to remove.
3 Unscrew the three lower hinge screws and hinge
if necessary.
Loading...