Electrolux E23BC68JPS4, E23BC68JPS5, E23BC68JPS6, E23BC68JPS7, E23BC68JPS8 Installation Guide

...
Installation Instructions rot
_Please refer to your Use _t Care Guide for more details.
French Door Bottom Freezer/Refrigerator
DO NOT REMOVE this label until the refrigerator has been leveled. Please follow all instructions for leveling your refrigerator.
Pre arin For Installation
Besureto coordinatesite preparation and installationwith your kitchen contractor•
Includethese minimum guidelines in your site preparation:
* Choosea place near agroundedelectrical outlet•
Do not usean extension cord or an adapter plug. Avoid direct sunlight andclose proximity to a range,dishwasher or
other heat source• Floorshould belevelandable to support afully loaded refrigerator•
Therefrigerator's Ice Dispenserrequires water supply access•
Planfor easyaccess to counter topswhen removing food. For complete accesstodrawers and freezer baskets,doors must beableto fully open.
Loadrefrigerator from side of cabinet only.
®
Do not run retainingstraps over handles nor overtighten straps•
®
Neveruse refrigerator handles to move the refrigerator•
Allow thefollowing clearancesfor easeof installation, proper air circulation, and plumbing and electrical connections: Sides& Top:3/8inch / Rear:1 inch
ConnectWaterSupply
BeforeInstallingTheWaterSupplyLine, YouWillNeed:
* BasicTools:adjustablewrench, flat-blade screwdriver,
andPhillipsTMscrewdriver Accessto a household cold water line with water
pressure between30 and 100 psi. Awater supply line made of 1Ainch (6 ram) OD,copper or stainless steeltubing• Todeterminethe length of tubing needed,measurethe distancefrom the ice maker inletvalve at the backofthe refrigeratorto your cold water pipe.Then add approximately 7 feet, so the refrigeratorcan bemoved out for cleaning•
Ashutoff valve to connect the water supply line to your householdwater system• DONOTusea self- piercing type shutoff valve•
A compressionnut andferrule(sleeve)for connectinga copperwatersupplyline tothe icemakerinletvalve•
To Connect Water Supply Line To Ice Maker Inlet VaNe
1. Disconnectrefrigerator from electric power source.
2. Placeend of water supply lineinto sink or bucket• TurnON water supply andflush supply line until water isclear•Turn OFFwater supply at shutoff valve•
3. Removeplasticcap from water valve inlet and discardcap.
4. If you use copper tubing - Slide brass compression nut,then ferrule (sleeve) onto watersupply line•
Pushwatersupp,y,neintowaterva,ve,n,etasfaras it will go (1Ainch)• Slide ferrule (sleeve)into valve
inletand finger tighten compression nut onto valve• Tightenanother halfturn with a wrench; DONOT 0vertighten.See Figure 1,
Ifyou usestainlesssteeltubing - Thenutand
ferrule arealreadyassembledonthe tubing. Slide
compressionnut onto valve inlet and finger tighten compressionnut onto valve•Tightenanother half turn with awrench; DONOTovertighten.See Figure 2.
5. Withsteelclampand screw,secure water supply line (coppertubing only) to rearpanelof refrigeratoras
shown•
6. Coilexcesswater supply line (copper tubing only), about 21/2turns, behind refrigerator as shown and arrangecoils so they do not vibrate or wear against anyother surface.
7. TurnON water supply at shutoff valve and tighten connections that leak.
8,
Reconnect refrigerator to electrical power source.
9.
Toturn icemaker on, lower wire signal arm (freezer icemaker) or set the ice maker's 0n/0ff power switch
tothe "ON" position (fresh food ice maker).
0nclude enough tubing in loop to allow
moving refrigerator out for cleaning.)
Figure1
/// _, ;_.>_ "---Bracket
/// 1) vow"e,
III /I/ 2_':,_
Ill///_ _ ---_ate_Va!ve
ngure2
LeveIRefri erator&Ad'ustDoors ifnecessar
* Allfour corners of the cabinetmust restfirmly onthe floor.
Thesides should tilt 1Ainch (6 ram) from front to back (to ensure that doors closeand seal properly).
. Doors should align with each other and be level. _
Mostoft,esecoudiUouscaubemetbyraisingorlowering
the adjustable flout rollers,
Tolevel thecabinet using the front rollers:
1 Youcan raise or lower eachdoor. Usea 3/8inchsocket
wrenchto turn theadjustment screws (1 perside). Toraise: turn adjustment screw clockwise.
Tolower: turn adjustmentscrew counterclockwise.
2 Ensure both doors are bind-free with their seals
touching the cabinet on all four sides and that cabinet is stable.
3 After unit is leveled, lower anti-tip leg until it contacts
thefloor.
.... oo
Compression
Not
Ferrule
(Sleeve)
water line
'_ Water Valve
Bracket
_vaiVei"iei
Valve
Copper water line from household water supply
Sta n ess
steel
water line
_ 6 ft. Stainless Steel water line
from household water supply
Doors final adjustment using the adjustable lower hinge (select models, if necessary):
1 Open doors to 90 degrees. 2 Remove screw.
3 Lift the door while adjusting the washer.
To raise the door: rotate washer clockwise. To lower the door: rotate washer counterclockwise.
4 Replace the screw, ensuring it is between the spokes of the hinge washer. Screw will not be
tight, just insert until it is flush with the hinge.
BottomofOoo i:i
Remove Screw
Levelin Freezer Drawer if necessar
1. Remove sex
Check gasket seal around top, bottom, and sides of freezer drawer. If gasket is not sealed, open drawer and slightly loosen 4 drawer screws
(2 on each side) to allow drawer to rotate.
3. Close drawer and recheck the seal on the gasket (A). Open the drawer grabbing by the sides in the center
(B). Be careful not to rotate the drawer.
4. Tighten 4 drawer screws.
5. Recheck gasket seal.
6. Install the toe grille by fitting into place.
Remove Internal Shi =n Materials
Electrolux uses packing foam and tape to secure the internal parts of your refrigerator for shipping. Once the refrigerator is in position, you can remove this material.
What's Next?
Congratulations! You are ready to begin enjoying your new Electrolux refrigerator.
For important safety instructions and to learn how to operate your refrigerator, please read the entire Use & Care Guide.
You may want to start with the "Normal Operating Sights & Sounds" section of the Guide to learn what to expect during typical operation.
Please register your product. You can register online at www.electroluxappliances.com, or
you can simply send in the Registration Card.
[]Installation Check List
Doors
[] Handles are secure and tight [] Door seals completely to cabinet on all sides
[] Fresh food doors are level
[] Refrigerator is level, side to side and tilted
1Ainch (6 mm) front to back [] Toe grille is properly attached to refrigerator [] Cabinet issitting solid on all corners
Electrical Power [] House power turned on [] Refrigerator plugged in
Raising/Lowering Door
Remove Hex
S_ew
Push Against
Freezer Drawer
[
_iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
,_ _
IB I
_ I _ _i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i
Ice Maker [] House water supply connected to
refrigerator
[] No water leaks present at all connections [] ice Maker is turned ON.
Final Checks [] Shipping material removed
[] Fresh Food and Freezer temperatures set
If you are not satisfied with the installation of your refrigerator, please contact the store where you purchased it or call 1-877-435-3287 for assistance. P/N:242046601
Loading...