Electrolux EI23CS55GB6, EI23CS55GB7, EI23CS55GS6, EI23CS55GS7, EI23CS55GW6 Installation Guide

...

Installation Instructions for Side-By-Side Refrigerator This document should only be removed by customer after installation.

Tools Necessary:

1 Pro are TheinstallationSite

Your refrigerator is designed to bepart of a built-in kitchen cabinetsystem. Besureto coordinate site preparation and

installation with your kitchencontractor. Includetheseminimum guidelinesin your sitepreparation:

* Choosea placenearagrounded electrical outlet.

Donot use an extensioncord or an adapterplug.

Avoid direct sunlight and close proximity to a range, dishwasher or other heat source.

Floorshould beleveland ableto support a fully loaded refrigerator.

The refrigerator's Ice & Water Dispenser requires water supply access.

. Planfor easyaccessto countertops whenremovingfood.

Forcomplete access to drawers and freezerbaskets,

doors must be ableto fully open.

Allow the following clearancesfor easeof installation, proper air circulation, and plumbing and electrical connections: Sides & Top:3/8 inch Rear. 1 inch

Trans ortUn acka ed Refri oratorToSite

Bynow,you havealready removedyour refrigerator'sshipping carton.You rnaystill need

to usea hand truck tomove it through closespacesor entrances. Ifthe refrigeratoris

largerthan anentrance,consider two options:

Removethe entrancedoor if one exists. Removethe refrigeratordoors (see howin your Use& CareGuide).

Whenusing a hand truck:

* Loadrefrigerator from sideof cabinet only.

Donot run retainingstraps over handles. Donot over-tighten retaining straps. Neveruserefrigeratorhandlestomovetherefrigerator.

* Removetapefrom doors only after unit is in place.

ConnectWaterSu !

Before Installing The Water Supply Line, You Will Need:

* BasicTools: adjustable wrench, flat-blade screwdriver,

and PhillipsTMscrewdriver Access to a household cold water line with water

pressure between 30 and 100 psi.

A water supply line made of 1ginch (6.4ram) OD, copper

or stainless steel tubing. To determine the length of

tubing needed,measure the distance from the ice maker

inletvalve atthe backof

the refrigerator to your cold water pipe. Then add

approximately 7 feet (2.1

meters), so the refrigerator

can be moved out for cleaning (as shown).

A shutoff valve to connect the water supply line to your

household water system. DO NOTuse a self-piercing type

shutoff valve. A compression nut

and ferrule (sleeve)for connecting a copper water

supply line to the ice maker

inletvalve.

To Connect Water Supply Line To Ice Maker

Inlet Valve

1. Disconnect refrigerator from electric power

SOUrCe,

2. Place end of water supply line into sink or bucket. Turn ON water supply and flush sup-

ply line until water is clear. Turn OFFwater supply at shutoff valve.

3. Remove plastic cap from water valve inlet and discard cap.

4. If you use copper tubing - Slide brass compression nut, then ferrule (sleeve) onto

water supply line. Push water supply line into water valve inlet as far as it will go

(1Ainch/6.4 mm). Slide ferrule (sleeve) into alve inlet and finger tighten compression nut onto

valve. Tighten another half turn with a wrench; DO NOT over tighten. See Figure 1.

If you use stainless steel tubing - The nut and ferrule are already assembled on the tubing. Slide compression nut onto valve inlet and finger ghtencompression nut onto valve. Tighten another

half turn with awrench; DO NOTover tighten. See Figure 2.

With steel clamp and screw, secure water supply line (copper tubing only) to rear panel of refrigerator as shown.

6. Coil excess water supply line (copper tubing and arrange coils so they do not vibrate or

7. Turn ON water supply at shutoff valve and

8. Reconnect refrigerator to electrical power

9. Toturn ice maker on, lower wire signal arm ( switch to the "l" position (rear mounted).

\I Z

_at_ Vak, e

t (it;elude erlough _ubir;9 it; _op m alk_w

_nly), about 2½ turns, behind refrigerator as shown _ar against any other surface.

hten any connections that leak. Jrce.

_ide mounted) or set the ice maker's 0n/0ff power

iiii_iiiii_i_!i!_ii_i_i!iiii_ili!_!!iii_i_i!iii!_ili_I_I_ii!i!ii!i!_i;iiii_iiiii_iiiii_iiiiiiiii!iiiii_!iiii!!i;!!i_i_i_i_i_i_i_ii_i;!_iiiiii_i!ii!i_i_!iiiii!i!iiii_iii_i!!i,iii!i_iii!_i:i_i!iiiiii!;ii_!ili;iiii!_!ii!i!_!_i;i!i_i_i_:_:!_!_i!_i_i!_i_i_:i_i_!i_i_!_i_i_i_!_!;!_ii_i_!i_i_!_;_i!i!_:!_!i!_!i_;iii_!i_;_!i_;_!i_;i!_i_!_!!!i_!!;!_:_!_i_!_!JJii_!i!i_!i_i_!_!!i_i!i_!i_!_i_ii!_!!_!i_i;i_!!iii;i_i_i_i_i_i_i_ii!i!_ii!i!_i_!_i_:!!!_:_;i_ii_i_i:_!_i_i!_i!_!_i!_iij!_i_!_!ii__i_i_i:!ii!iii_i!i!_i:ii!_i_i!ii_i!iii_i!i_i!iiii_ill_i_iiii_i:i!i_!,!i!_!,!i_!_i_i_!i!ii

PlaceInPermanent

tuition

LevelRefrigerator & Adjust Doors(if necessary)

To install toe grille !io.o"_._,_ _

lower hinges of refrigerator.

2 While pushing toe grdle firmly against binet, fasten bottom

1 Open both doors. Slide left and right es of toe grille over

clips of toe grille to cabinet. 3 Fasten top clips to cabinet. 4 Close the doors. Fasten right and left side clips into groove of bottom hinge.

To remove toe grille

1 With both doors closed, unfasten right and left side clips of toe

grille from bottom hinge grove. 2 Open both doors. Press firmly on top oftoe grille until top of toe

grille pops off. 3 Pull toe grille outward towards your bod_ .nd off of lower hinges.

NOTE: Level the unit with the adjustable rollers _fore leveling the doors. To level the doors using the adjustable lower hinge (some models): _i

1 Before leveling either door, remove set screw that locks door height into posi- _1I_li °_'_

tion. (The door cannot be adjusted without set screw removed.) _ EtCh/

2 If the refrigerator door is lower than the freezer door, raise the refrigerator

door by turning the adjustment screw counterclockwise using a 7/l_inch

wrench. (See iflustration.)

3 If the freezer door is lower than the refrigerator door raise the

freezer door byturningthe adjustment screw counterclockwise _1 .....................

using a 7/_ inch wrench. (See dlustration.) ....._!_,!:_!!_!_i........................,_*::;::::........................................

4 After leveling, verify door stop contacts lower hinge and top of door i:_;

does not contact upper hinge through full movement of door (from % i

fully closed to fully open). '_'i

5 Replace the toe grdle by fitting it into _ ce.

'½.,oo,o,,oo_%,_o,,,,o-_

T T

RemoveInternal Shi in Materials

Electrolux usespacking foam and tape to secure the internal parts of your refrigerator for shipping. Once the refrigerator is in position, you can remove this material.

1 FOAM BLOCK-

....................

1 PIECE OF TAPE--

3 PIECES OF TAPE--

2 PIECES OF TAPE_

5 PIECES OF TAPE--

2 PIECES OF TAPE_

4 HECES OF TAPE--

2 PIECES OF TAPE _

Location of these materials may vary depending on yourmodel,

_SHELF SPACER WiTH TOE GRILL

_ il-- 4P_ECESOFTAPE

4 PIECES OF TAPE

_ I BOX OF DOOR BINS

AND DAIRY COMPARTMENT

_--_4 P,ECESOFTAPE

i _ . ,---"'t _ 1 BOX OF DOOR HANDLES X J _ AND 2 PIECES OF TAPE

_--_P,ECESOFTAPE

C_--_ 7 PIECES OF TAPE

FOAMOLOCKS

7 Problems?TryTheseSuggestions

Operation problems are possible if any of the installation tasks are not completed. Hereis a list of things to check for:

Is the refrigerator's power cord plugged in? Is the refrigerator connected to the household water supply? Ifyou had to remove the refrigerator and freezer doors, did you reattachwater and power connectors

at the door hinges? (Seethe Use& CareGuide for detailed instructions on removing and replacing doors.)

Is the ice maker power switch turned On?

Other possibilities to check:

Is the power to the receptacleturned on? Is the water filter above thefresh food compartment fully seated (see Use& CareGuidefor details)?

Ifyou still haveoperation problems after checking thesesuggestions, please seethe "Solutions To

Common Problems" section in your Use& Care Guide.

Whats Next.

Congratulations. Youare ready to beginenjoying your newElectrolux refrigerator.

* To becomeaware of important safety instructions and learn how to operateyour refrigerator, please

readthe entire Use & CareGuide.

* Youmay want to start with the "Normal OperatingSights & Sounds" section of the Guideto learn

more about what to expect during typical operation.

Pleaseregister your product. You can register online at www.electroluxusa.com, or you can simply

send in the Registration Card.

, ?

Andthankyou for choosingElectro/ux.

9 I--4In II i n h k ff Li

Doors iceMaker

E]Handlesare secure and tight E]Door seals completely to cabinet on all sides

E]Freezerdoor is level across the top

Leveling

E]Refrigerator is level,side to side and tilted

W' (6ram) front to back E]Toegrille is properly attached to refrigerator DCabinet is setting solid on all corners

Electrical Power

E]Housepower turned on E]Refrigerator plugged in

E]House water supply connected to

refrigerator

E]No water leaks present atall connections -

recheck in 24 hours E]lce Maker is turned ON E]lce & WaterDispenser operates correctly E]Front filter must be flush with filter housing

(some models) Final Checks

E]Shipping material removed E]Fresh Foodand Freezertemperatures set

E]Crisper Humidity controls set E]Registration Card sent in

Not satisfied with the installation of your refrigerator? L>Please contact the store you purchased it from.