Electrolux E30SO75ESS, E30SO75ESSA, E30SO75ESSB, E30SO75FPSA Installation Guide

iNSTALLATiON AND SERVICE MUST BE PERFORMED BY A QUALiFiED iNSTALLER.

iMPORTANT: SAVE FOR LOCAL ELECTRICAL iNSPECTOR'S USE.

READ AND SAVE THESE iNSTRUCTiONS FOR FUTURE REFERENCE.

The electrical requirements for this oven are 240 volts, 15 amps.

The oven has a 6-15 pJug and requires a 6-15 receptacle.

NOTE:

1. Basemust be capable of supporting 200
pounds (90.7 kg).

2. Make sure base islevel and front of cabinet
issquare. Ifthe cabinet baseisnot level, the

oven will tend to slide out when opening

the door.

3. Minimum required distance is 36" (91.44
cm) from the floor.

4. At the rear of the opening, provide a 3
pronged, polarized, electrical outlet, 240

volt A.C., 15 amp. or larger. This outlet

should not be located in the shaded area
of Figure I. It isexceedingly important that

the outlet be 240 volts and 15 amps. for

optimum oven performance.

5. Minimum required distance between the
high speed oven and the wall oven should

be 3-inches.

Remov
shipping supports _ Replace these

(both sides) screws after

shipping support
removal (both sides)

k_

Figure 1

30" (76.2) High Speed

30" (76.2) High Speed 22%" (56.8) 22%" (57.5) 24" (61.0) rain. 21"/_/(55.1) 21 _s/_6"(55.7) 30" (76.2) min.

All dimensions are in inches (cm).

Oven 30" (76.2) 2227/32" (58.0) 21%" (54.0) 221s/16" (58,2)

Oven

Important Notes to the Installer

I. Read all instructions contained in these installation

instructions before installing the high speed oven.

2. Removeallpacking materialfrom the oven compartments
before connecting the electrical supplyto the high speed
oven. Remove the 2 shipping duct supports (seefigure

1)by removing the 4 screws securing them. Reinsert 2

screws (each side) to secure the stainless cover.

Printed in United States TINSEB424MRRO

3. Observe all governing codes and ordinances.

4. Be sure to leave these instructions with the consumer.

Important Note to the Consumer

Keep these instructions with your Owner's Guide for future
reference.

iMPORTANT SAFETY
iNSTRUCTiON

• Never use your high speed oven for warming or
heating the room. Prolonged use of the high speed
oven without adequate ventilation can be dangerous.

1. Carpentry

Refer to figure 1 for the dimensions applicable to your
appliance, and the space necessary to receive the oven.
The oven support surface may be solid plywood or similar
material, however the surface must be level from side to

side and from front to rear.

2. Electrical Requirements

This appliance must be supplied with the proper voltage
and frequency, and connected to an individual, properly
grounded branch circuit, protected by a circuit breaker or
fuse, having amperage as noted on the rating plate (the
rating plate is located on the oven frame).

Observe all governing codes and local ordinances

During cold temperature weather to prevent

damage to the oven control, wait at least three (3) hours
after receiving this built-in oven before switching the
power. This will prevent possible damage to the built-in
oven control at power on.

3. Cabinet Installation

The high speed oven can tip when

the door is open. The Anti-Tip brackets supplied
with the high speed oven must be attached to the
cabinet and the appliance to prevent tipping of the
high speed oven and injury to persons.

Anti-tip Brackets Installation Instructions

I. Unpack the high speed oven and find the 2 Anti-

Tip brackets and screws included in the literature

package.

2. Install the Anti-Tip bracket in the cabinet as shown
on figure 2. Note: To prevent damage to cabinet, it is

recommended to drill _/_6"(0.16 cm) dia. pilot holes before
installing the Anti-Tip brackets.

3. High Speed Oven Installation

Never hold the door handle when moving the

oven. Two persons are required to install the oven.

Place the oven adjacent to the opening on a table or
stand. Plugthe power supply cord into the electrical outlet.
Carefully guide the oven into the prepared opening. Avoid

pinching cord between oven and wall (seefigure 3). Push
the unit in and against the cabinet. The oven side bracket
will clip into the Anti-Tip brackets (see figure 2).

4. To pull out the oven for servicing insert the tool supplied
with the appliance both side at the sametime in the hole

located on the side frame and visible when the door is
opened. After inserting the tool pull the oven towards
you (seefigure 4).