electroluxicon.com
Wave-Touch®Controls
Sleek control panel illuminates with just a touch
and fades away after an option is selected.
Automatic Cooking Settings
Pre-programmed settings give you the versatility
to combine both microwave cooking and
convection heat.
Sensor-Cook Technology
Intelligent sensors automatically adjust cooking
time and power level based on what you are
cooking.
Convection Cooking
Circulates hot air through your microwave
to cook foods evenly.
Built-In Microwave With Drop-Down Door
E30MO75HPS professional series
30" BUILT-IN MICROWAVE WITH DROP-DOWN DOOR
Oven Cavity
Watts
Oven Interior
Interior Krypton Light
Porcelain Enamel Turntable
PANEL FEATURES
Wave-Touch®Controls
VFD Front Display with Blue Indicators
Electronic Clock & Timer
Humidity Sensor
Power Levels
Touch Pad Controls
Auto Start
Auto Defrost Options
Auto Cook Options –
Pizza Slice (1), Snacks (3), Kid’s Meals (3)
Soften/ Melt (4), Beverage (1)
Convection Cook Categories –
Auto Broil (4), Auto Roast (4), Auto Bake (4)
Auto Reheat Categories –
Breads/ Muffins (2), Pasta (1)
Sensor One Touch Categories –
Cook (5), Reheat (1), Popcorn (2), Baked Potato (1),
Frozen Vegetables (1), Fresh Vegetables (2)
Stage Cooking Options
Add 30 Seconds
Keep Warm
Custom Help Options
Panel Lock
Demo Mode
Adjustable Sound Level for Timers/ Reminders
More/ Less Function
Power Failure Indicator
POWER RATINGS
Microwave – (Watts@120 Volts)
Convection – (Watts@120 Volts)
Amps@ 120 Volts
Frequency (Mhz)
Voltage Rating
Connected Load (kW Rating) @120 Volts
‡
SPECIFICATIONS
Oven Cavity Dimensions–
Height
Width
Depth
Overall Exterior Dimensions –
Height
Width
Depth
Approved for Under-Counter Installation
Approved for Electric Single Oven Combination Installation*
Power Cord Location
Shipping Weight (Approx.)
‡ For use on adequately wired 120V, dedicated circuit having 2-wire service with
a separate ground wire. Appliance must be grounded for safe operation.
* Approved to be used in combination with any Electrolux ICON®Electric Single
Wall Oven and/or Warmer Drawer. (Not approved to be used above any gas wall oven.)
NOTE: Always consult local and national electric codes. Refer to Product Installation Guide
for detailed installation instructions on the web at electroluxicon.com.
Specifications subject to change.
1.5 Cu. Ft.
900
Cobalt Blue
Yes
Yes
Yes
Yes
Yes
Yes
11
37
Yes
6
12
12
3
12
4
Yes
No
Yes
Yes
Yes
Yes
Yes
Yes
1550
1500
13.7
2450
120V /60 Hz/15A
1.6
9-5/8"
16-1/8"
16-1/8"
22"
30"
21-11/16"
No
Yes
Left Bottom Rear
89 Lbs.
30" Built-In Microwave With Drop-Down Door Specifications
•
Product Weight – 84 Lbs.
•
Voltage Rating –120V / 60 Hz / 15 Amps
•
Connected Load (kW Rating) @120 Volts = 1.6kW
(For use on adequately wired 120V, dedicated circuit having 2-wire
service with a separate ground wire. Appliance must be grounded
for safe operation.)
•
Amps @120 Volts =13.7 Amps
•
Always consult local and national electric codes.
•
Allow at least 15" clearance for oven door depth when open.
•
Minimum required distance from floor is 36".
•
Minimum 20-1/8" deep oven cutout dimension is critical for proper
installation for oven and faceplate to fit flush against cabinet front.
•
Full oven base of solid plywood or similar material required, capable
of supporting 150 Lbs.
•
Base must be level and cabinet front must be square.
•
Grounded outlet should NOT be located in shaded area, as indicated.
•
Built-In Microwave is NOT approved to be used under counter.
•
Built-In Microwave can be built in alone or is approved to be used in
combination with any Electrolux ICON
®
Electric Single Wall Oven
and/or Warmer Drawer. (Refer to model-specific Combination Installation
Specification pages on web.)
•
When used in combination with another Electrolux ICON®built-in product,
a minimum clearance of 2-1/8" required from bottom of Built-In Microwave
cutout to top edge of companion product’s faceplate, leaving a 2" visible
gap between both product faceplates.
Note: For planning purposes only. Refer to Product Installation Guide on the
web at electroluxicon.com for detailed instructions.
Built-In Microwave With Drop-Down Door
E30MO75HPS professional series
High standards of quality at Electrolux Home Products, Inc. mean we are
constantly working to improve our products. We reserve the right to change
specifications or discontinue models without notice.
Electrolux Major Appliances, N.A.
USA
•
10200 David Taylor Drive •Charlotte, NC 28262 •1-877-4electrolux (1-877-435-3287)
•
electroluxicon.com
CANADA
•
5855 Terry Fox Way •Mississauga, ON L5V 3E4 •1-800-265-8352
•
electroluxicon.ca
E30MO75HPS 04/11 © 2011 Electrolux Home Products, Inc. Printed in the U.S.A.
2111/16"
Allow at least
15" clearance
for door depth
when open
22"
203/4"
231/2"
28"
30"
Power
supply
location
(left
bottom
rear)
Bottom Duct Assembly
C
L
120V/60Hz
grounded outlet
Outlet should NOT
be located within
shaded area
201/8" min.
281/2"min.
29"max.
21"
min.
21
1
/2"
max.
Bottom Duct Assembly
4"
6"
18"
201/8"
min.
21"
min.
21
1
/2"
max.
Full plywood
base required
to support
150 lbs.
2"
min.
28
1
/2"min.
29"max.
2"
(visible
gap)*
24"
min.
301/8"
min.
36"min.
required
distance
to floor
*Note: When used in combination with
another Electrolux ICON
®
built-in product, a
minimum clearance of 2
1
/8" required from
bottom of Built-In Microwave cutout to top
edge of companion product’s faceplate,
leaving a 2"visible gap between both
product faceplates.
Use these dimensions and clearance instructions for planning purposes only. For detailed installation
instructions, refer to installation guide, packed with product, or on the web at electroluxicon.com.
Front
Top
General Installation Guidelines
with Counter-Depth French Door Refrigerator
High standards of quality at Electrolux Home Products, Inc. mean we are
constantly working to improve our products. We reserve the right to change
specifications or discontinue models without notice.
Electrolux Major Appliances, N.A.
USA
•
10200 David Taylor Drive •Charlotte, NC 28262 •1-877-4electrolux (1-877-435-3287)
•
electroluxicon.com
CANADA
•
5855 Terry Fox Way •Mississauga, ON L5V 3E4 •1-800-265-8352
•
electroluxicon.ca
INSTGDLNS_FDR EI 10/10 © 2010 Electrolux Home Products, Inc. Printed in the U.S.A.
Use these dimensions and clearance instructions for planning purposes only. For detailed installation
instructions, refer to installation guide, packed with product, or on the web at electroluxicon.com.
Front
Top
General Installation Guidelines
with Counter-Depth Side-by-Side Refrigerator
High standards of quality at Electrolux Home Products, Inc. mean we are
constantly working to improve our products. We reserve the right to change
specifications or discontinue models without notice.
Electrolux Major Appliances, N.A.
USA
•
10200 David Taylor Drive •Charlotte, NC 28262 •1-877-4electrolux (1-877-435-3287)
•
electroluxicon.com
CANADA
•
5855 Terry Fox Way •Mississauga, ON L5V 3E4 •1-800-265-8352
•
electroluxicon.ca
INSTGDLNS_SSR EI 10/10 © 2010 Electrolux Home Products, Inc. Printed in the U.S.A.
High standards of quality at Electrolux Home Products, Inc. mean we are
constantly working to improve our products. We reserve the right to change
specifications or discontinue models without notice.
Electrolux Major Appliances, N.A.
USA
•
10200 David Taylor Drive •Charlotte, NC 28262 •1-877-4electrolux (1-877-435-3287)
•
electroluxicon.com
CANADA
•
5855 Terry Fox Way •Mississauga, ON L5V 3E4 •1-800-265-8352
•
electroluxicon.ca
MODD_EW_WD INST 10/10 © 2010 Electrolux Home Products, Inc. Printed in the U.S.A.
30" Combination Installation Specifications
•
Always consult local and national electric codes.
(Refer to product-specific electrical specifications on this page.)
•
Minimum 24"deep cutout dimension is critical for proper combination
installation, to ensure that each built-in product’s faceplate will fit
flush against cabinet front.
•
Bases must be level and cabinet front must be square.
•
Minimum 4-1/2"required distance from bottom of Warmer Drawer
cutout to floor.
•
Respect critical dimensions as noted for proper installation of built-In
products.
•
Minimum 23-1/4" clearance needed for Wall Oven door depth
when open.
30" Built-In Convection Microwave Specifications
•
Product Weight – (E30MO75HPS/ E30MO75HSS) 84 Lbs.
•
Voltage Rating –120V / 60 Hz / 15 Amps
•
Connected Load (kW Rating) @120 Volts = 1.6kW
(For use on adequately wired 120V, dedicated circuit having 2-wire
service with a separate ground wire. Appliance must be grounded
for safe operation.)
•
Amps @120 Volts =13.7 Amps
•
Full oven base of solid plywood or similar material required, capable
of supporting 150 Lbs.
•
Minimum 2-1/8"clearance required from bottom of Built-In Microwave
cutout to top edge of Wall Oven’s faceplate, leaving a 2"visible gap
between both product faceplates.
30" Electric Single Wall Oven Specifications
•
Product Weights – (E30EW75GPS) 178 Lbs. / (E30EW75GSS) 175 Lbs.
•
Single phase 3- or 4-wire cable, 120/240 or 120/208 Volt, 60 Hertz
AC only electrical supply with ground required on separate circuit
fused on both sides of line.
•
Connected Load (kW Rating) @ 240/208 Volts = 4.0/ 3.0 kW
•
Amps @ 240/208 Volts =16.6 / 14.4 Amps
•
To support Wall Oven, two 3"-wide x 3/4"-thick planks must be installed
as a base, capable of supporting 200 Lbs. Do NOT use full base, since
planks are necessary to allow for proper air displacement.
30" Warmer Drawer Specifications
•
Product Weights – (E30WD75GPS/ E30WD75GSS) 49 Lbs. /
(E30WD75GTT) 41 Lbs.
•
Voltage Rating –120V / 450W / 60 Hz /15 Amps
•
Connected Load (kW Rating) @120 Volts = 0.45kW
(For use on adequately wired 120V, dedicated circuit having 2-wire
service with a separate ground wire. Appliance must be grounded
for safe operation.)
•
Amps @120V = 3.75 Amps
•
Full base of solid plywood or similar material required, capable of
supporting 100 Lbs.
Note: For planning purposes only. Refer to Product Installation Guide
on the web at electroluxicon.com for detailed instructions.
For detailed product dimensions
and installation specifications, refer
to model-specific product page and
installation guide on web
24"min.
3"max.
††
301/8" min.
97/8"min.
10
1
/4"max.
1
3
/4"min.
†
Full plywood base
required to support
150 lbs.
Full plywood base
required to support
100 lbs.
281/2"min.
28
7
/8"max.
281/2"min.
28
3
/4"max.
Two 3" wide
by
3
/4" thick
planks must be
installed, capable
of supporting
200 lbs.
4"x 4" opening to route
armored cable
281/2"min.
28
3
/4"max.
120V/60Hz
grounded electrical
outlet should NOT
be located within
shaded area
4
1
/2"min.
required
21"min.
21
1
/2"max.
24"min.**
(critical
dimension)
Electrical junction
box location
Bottom of
oven cutout
115/8"min.**
(critical
dimension)
* Minimum 21/8"
clearance required
from bottom of
Built-In Microwave
cutout to top edge of
Wall Oven’s faceplate,
leaving a 2"visible
gap between both
product faceplates.
** Critical dimension –
MUST be applied
†
Maximum height
depends on critical
dimension (115/8")
††
Electrical junction
box for Wall Oven
must be lower than
the Warmer Drawer
cutout
30" Warmer
Drawer Cutout
For models:
E30WD75GPS
E30WD75GSS
E30WD75GTT
C
L
6"
18"
2"
(visible
gap)*
4"
30" Electric Single
Wall Oven Cutout
For models:
E30EW75GPS
E30EW75GSS
30" Built-In
Microwave Cutout
For models:
E30MO75HPS
E30MO75HSS
281/2"min.
283/4"max.
30" Combination Installation –
Built-In Microwave/Single Wall Oven/Warmer Drawer
30" Combination Installation –
Built-In Microwave/Single Wall Oven
High standards of quality at Electrolux Home Products, Inc. mean we are
constantly working to improve our products. We reserve the right to change
specifications or discontinue models without notice.
Electrolux Major Appliances, N.A.
USA
•
10200 David Taylor Drive •Charlotte, NC 28262 •1-877-4electrolux (1-877-435-3287)
•
electroluxicon.com
CANADA
•
5855 Terry Fox Way •Mississauga, ON L5V 3E4 •1-800-265-8352
•
electroluxicon.ca
MODD_EW INST 10/10 © 2010 Electrolux Home Products, Inc. Printed in the U.S.A.
30" Combination Installation Specifications
•
Always consult local and national electric codes.
(Refer to product-specific electrical specifications on this page.)
•
Minimum 24"deep cutout dimension is critical for proper combination
installation, to ensure that each built-in product’s faceplate will fit
flush against cabinet front.
•
Bases must be level and cabinet front must be square.
•
Minimum 4-1/2"required distance from bottom of Wall Oven cutout
to floor, 31" suggested.
•
Respect critical dimensions as noted for proper installation of built-In
products.
•
Minimum 23-1/4" clearance needed for Wall Oven door depth
when open.
30" Built-In Convection Microwave Specifications
•
Product Weight – (E30MO75HPS/ E30MO75HSS) 84 Lbs.
•
Voltage Rating –120V / 60 Hz / 15 Amps
•
Connected Load (kW Rating) @120 Volts = 1.6kW
(For use on adequately wired 120V, dedicated circuit having 2-wire
service with a separate ground wire. Appliance must be grounded
for safe operation.)
•
Amps @120 Volts =13.7 Amps
•
Full oven base of solid plywood or similar material required, capable
of supporting 150 Lbs.
•
Minimum 2-1/8"clearance required from bottom of Built-In Microwave
cutout to top edge of Wall Oven’s faceplate, leaving a 2"visible gap
between both product faceplates.
30" Electric Single Wall Oven Specifications
•
Product Weights – (E30EW75GPS) 178 Lbs. / (E30EW75GSS) 175 Lbs.
•
Single phase 3- or 4-wire cable, 120/240 or 120/208 Volt, 60 Hertz
AC only electrical supply with ground required on separate circuit fused
on both sides of line.
•
Connected Load (kW Rating) @ 240/208 Volts = 4.0/ 3.0 kW
•
Amps @ 240/208 Volts =16.6 / 14.4 Amps
•
Full oven base of solid plywood or similar material required, capable of
supporting 200 Lbs.
Note: For planning purposes only. Refer to Product Installation Guide
on the web at electroluxicon.com for detailed instructions.
24"min.
3" max.
281/2"min.
28
7
/8"max.
30" Electric Single
Wall Oven Cutout
For models:
E30EW75GPS
E30EW75GSS
281/2"min.
29"max.
4"x 4" opening
to route armored
cable
24"min.**
(critical
dimension)
2" min.
31"
suggested
distance
4
1
/2"
min.
required
Bottom cutout
edge must be
finish cut
Full base required
to support 200 lbs.
Electrical junction
box location
For detailed product dimensions
and installation specifications, refer
to model-specific product page and
installation guide on web
21"min.
21
1
/2"max.
2"
(visible
gap)*
30" Built-In
Microwave Cutout
For models:
E30MO75HPS
E30MO75HSS
Full plywood base
required to support
150 lbs.
120V/60Hz
grounded electrical
outlet should NOT
be located within
shaded area
C
L
6"
18"
4"
281/2"min.
29"max.
* Minimum 21/8"
clearance required
from bottom of
Built-In Microwave
cutout to top edge of
Wall Oven’s faceplate,
leaving a 2"visible
gap between both
product faceplates.
** Critical dimension –
MUST be applied
30
1
/8" min.
Loading...