
Air-O-Steam, Air-O-Steam - Touchline, Air-O-Convect, Air-O-Convect - Touchline
Quick Installation Guide
Rev: B - 12/11/2018

Due to continuous product research and development,
the information contained herein is subject to change without notice.
www.stoddart.com.au
www.stoddart.co.nz
Installation
Filtration System 4
Positioning 5
Drainage Connection 6
Detergent Tray (6 Grid, 10 Grid) 7
Oven Cleaner Connection (20 Grid) 7
Water Connection 8
Electrical Oven - Power 9
Gas Oven - Power 9
Total Dissolved Solids (TDS) Test 3
Chloride Test 3
Information
Electrical and Gas Connection 2
Water Connection 2
Attention 2

Due to continuous product research and development,
the information contained herein is subject to change without notice.
www.stoddart.com.au
www.stoddart.co.nz
Attention
Disclaimer:
The manufacturer and distributor cannot be held responsible or liable for any injuries or damages of any kind occurred
to persons, appliances or others, due to abuse and misuse of this appliance in regards to installation, un-installation,
operation, servicing or maintenance, or lack of conformity with the instructions indicated in this documentation.
All appliances made by the manufacturer are delivered assembled, where possible, and ready to install. Any installation,
un-installation, servicing, maintenance and access or removal of any parts, panels or safety barriers that is not
permitted, does not comply in accordance to this documentation, or not performed by a TRAINED AND AUTHORISED
SPECIALIST will result in the IMMEDIATE LOSS OF THE WARRANTY.
The manufacturer cannot be held responsible or liable for any unauthorized modifications or repairs. All modifications
or repairs must be approved by the manufacturer in writing before initiating. All modifications or repairs performed to
this appliance must be performed at all times by a TRAINED AND AUTHORISED SPECIALIST.
Read through the following instructions carefully before proceeding with the installation. Be sure to follow all relevant standard and local
codes. Please contact the Stoddart Service Department at 1300 307 289 if you are having problems with the installation of the unit.
Information
• This unit must be connected to an adequate supply of filtered potable water. (See page 3-4 for selection of an appropriate filter system)
• This unit must be connected to a waste water disposal system that:
(a) will effectively dispose of all waste water; and
(b) is constructed and located so that there is no likelihood of the waste water polluting the water supply or contaminating food.
• Regulations require that all units be installed to the appropriate Australian standards.
• Regulations require that authorised persons carry out all plumbing work.
Water Connection
IMPORTANT!
This unit must be installed in accordance with AS/NZS 3500.5
Information
• The electrical and/or gas supply must comply with the rating plate data.
• Ensure that the machine is connected to a suitably rated, dedicated and earthed power source with its own isolation switch.
Extension leads or power boards are not to be used.
• Regulations require that all units be installed to the appropriate Australian standards.
• Regulations require that authorised persons carry out all electrical and/or gas work.
• Users should also note that if the supply electricity cord is damaged in any way it should be replaced. Please contact Stoddart for parts
and we will advise how to do this in order to avoid any electrical hazard.
• The power cable should be dry and or isolated from moisture or water.
Electrical and Gas Connection
WARNING!
This unit must be installed in accordance with
AS/NZS 60335.1, AS/NZS5601

Due to continuous product research and development,
the information contained herein is subject to change without notice.
www.stoddart.com.au
www.stoddart.co.nz
Chloride Test
1. Remove Titrator from bottle and
replace bottle cap immediately.
2. Insert lower end of the Titrator into
water to be tested (approx 20mm of
water). DO NOT allow water to touch
yellow completion band at top of
Titrator.
3. Allow water to completely saturate the
wick of Titrator. Reaction is complete
when yellow band turns dark.
4. Note where the white chloride peak
falls on the scale. This represents the
unit value.
5. Refer to the table to convert the
Titrator units into salt concentration.
* Readings higher than 1.4 (32PPM)
require a Reverse Osmosis Unit to be
installed.
Total Dissolved Solids (TDS) Test
1. Remove the cover from the TDS meter,
turn on by pressing the On/Off button.
The display should read 000.
2. Insert lower end of the TDS meter into
water to be tested (approx 20mm of
water). DO NOT completely submerge.
3. Wait 5-10 seconds.
4. The number displayed on meter is
the TDS (Total Dissolved Solids) of the
water expressed in PPM (parts per
million) e.g. TDS = 220PPM.
5. When finished, turn the TDS meter off.
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
1
2
3
1.4
1.6
1.8
2.0
2.2
2.4
2.6
2.8
3.0
3.2
3.4
3.6
3.8
4.0
4.2
4.4
0.005
0.006
0.007
0.009
0.010
0.011
0.013
0.014
0.016
0.017
0.019
0.021
0.023
0.025
0.027
0.030
32
39
45
53
60
68
77
86
95
106
116
128
140
152
166
180
4.6
4.8
5.0
5.2
5.4
5.6
5.8
0.032
0.035
0.038
0.041
0.044
0.048
0.051
196
212
229
248
267
288
311
6.0 0.055 335
6.2 0.060 361
6.4 0.064 389
6.6 0.069 419
6.8 0.074 452
7.0 0.080 487
7.2 0.087 525
7.4 0.093 567
7.6 0.101 613
Units %NaCI CI Units %NaCI CI
ppm(mg/L)
Limit*
ppm(mg/L)
IMPORTANT!
Selection of the correct water ltration system to suit local water
conditions is CRITICAL. Failure to install the correct system according
to the following guidelines will void warranty.