Electrolux 99852 G User Manual

99852 G

Gas Hob

Operating Instructions

PERFECT IN FORM AND FUNCTION

Important Safety Information

You MUST read these warnings carefully before installing or using the hob. If you need assistance, contact our Customer Care Department on 08705 350350

Installation

z This hob must be installed by qualified personnel, according to the manufacturer’s

instructions and to the relevant British Standards.

z Any gas installation must be carried out by a registered CORGI installer.

z Remove all packaging before using the hob.

z Ensure that the gas and electrical supply complies with the type stated on the rating

plate, located near the gas supply pipe.

z Do not attempt to modify the hob in any way.

Child Safety

z This hob is designed to be operated by adults. Do not allow children to play near or

with the hob.

z The hob gets hot when it is in use. Children should be kept away until it has cooled.

z Children can also injure themselves by pulling pans or pots off the hob.

During Use

z This hob is intended for domestic cooking only. It is not designed for commercial or

z When in use a gas cooking hob will produce heat and moisture in the room in which

z When using the hob for a long period of time, the ventilation should be improved, by

industrial purposes.

it has been installed. Ensure there is a continuous air supply, keeping air vents in good condition or installing a cooker hood with a venting hose.

opening a window or increasing the extractor speed.

z Do not use this hob if it is in contact with water. Do not operate the hob with wet hands.

z Ensure the control knobs are in the ‘OFF’ position when not in use.

z When using other electrical appliances, ensure the cable does not come into contact

with the hot surfaces of the cooking appliance.

z Unstable or misshapen pans should not be used on the hob as unstable pans can

cause an accident by tipping or spillage.

z Never leave the hob unattended when cooking with oil and fats.

z Never use plastic or aluminium foil dishes on the hob.

z Perishable food, plastic items and areosols may be affected by heat and should not

be stored above or below the hob unit.

Service

z This hob should only be repaired or serviced by an authorised Service Engineer

and only genuine approved spare parts should be used.

Environmental Information

z After installation, please dispose of the packaging with due regard to safety and the

environment.

z When disposing of an old appliance, make it unusable, by cutting off the cable.

Keep this instruction book for future reference and ensure it is passed on to any new owner.

These instructions are only valid for countries whose identification symbols are shown on the cover of this instruction booklet and on the appliance itself.

Contents

Instructions for the User

Important Safety Information 2 Description of the Hob 5

Operation 6

Maintenance and Cleaning 7

Something Not Working? 8

Service and Spare Parts 9

Customer Care 9

Guarantee Conditions 10

Instructions for the Installer

Important safety requirements 12

Installation 13

Building In 14

Electrical connections 17

Wiring diagram 18 Fault Finding 19

Commissioning 22

Conversion from Natural Gas to LPG 23

Guide to Use the instructions

The following symbols will be found in the text to guide you throughout the Instructions:

Safety Instructions

Step by step instructions for an operation

))

)

))

Hints and Tips

Environmental Information

This appliance is manufactured according to the following EEC directives: 73/23 EEC - 90/683 EEC - 93/68 EEC 89/336 EEC - 90/396 EEC, current edition.

Description of the Hob

1. Hob Top

2. Semi-rapid Burners

3. Auxiliary Burner

4. Ultra-rapid Burner (triple crown)

5. Control knobs

INSTALLATION

Any gas installation must be carried out by a registered CORGI installer, and in accordance with existing rules and regulations.

The relevant instructions are to be found in the second section of this manual.

Please, ensure that, once the hob is installed, it is easily accessible for the engineer in the event of a breakdown.

WHEN THE HOB IS FIRST INSTALLED

Once the hob has been installed, it is important to remove any protective materials, which were put on in the factory.

Operation

Hob burners

To light a burner:

))

)

))

z Push in the relevant control knob and turn it to maximum position. z Upon ignition, keep the knob pushed down about 5 seconds. This will allow the

"thermocouple" (fig. 1 - letter C) to be heated and the safety device to be switched off, otherwise the gas supply would be interrupted.

z Then adjust the flame as required. z If the burner does not ignite, turn the control knob to zero, and try again.

Each control knob is equipped with a pilot light which gradually lights up according to the heat level that you select with the control knob.

When switching on the mains, after installation or a power cut, it is quite normal for the spark generator to be activated automatically.

To ensure maximum burner efficiency, you should only use pots and pans with a flat bottom fitting the size of the burner used (see table).

Burner minimum maximum

diameter diameter

Large (ultra-rapid) 180 mm. 260 mm. Medium (semi-rapid) 120 mm. 220 mm. Small (Auxiliary) 80 mm. 160 mm.

As soon as a liquid starts boiling, turn down the flame so that it will barely keep the liquid simmering.

If you use a saucepan which is smaller than the recommended size, the flame will spread beyond the bottom of the vessel, causing the handle to overheat.

Take care when frying food in hot oil or fat, as the overheated splashes could easily ignite.

If the control knobs become difficult to turn, please contact your local Service Force Centre.

A - Burner cap B - Ignition electrode C - Thermocouple

Fig. 1

Maintenance and Cleaning

Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob from the electricity supply.

The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool.

The Hob Top

Regularly wipe over the hob top using a soft cloth well wrung out in warm water to which a little wasing up liquid has been added. Avoid the use of the following:

- household detergent and bleaches;

- impregnated pads unsuitable for non-stick saucepans;

- steel wool pads;

- bath/sink stain removers. Should the hob top become heavily soiled, the following product s are recommended:

- for stainless steel hobs use a proprietary stainless steel cleaner;

- for other hobs use Hob Brite or Bar Keepers Friend.

If scratches or cracks are noticed, disconnect the appliance from the electrical supply and call your nearest Service Force Centre.

Fig. 2

Pan Supports

To keep the pan supports in the correct position, they are mounted on metal pins located in the back of the hob. After cleaning the hob, ensure the pan supports are properly placed as shown in fig. 2. The pan supports are dishwasher proof. If washing them by hand, take care when drying them as the enamelling process occasionally leaves rough edges. If necessary, remove stubborn stains using a paste cleaner.

Fig. 3

The Burners

The burner caps and crowns can be removed for cleaning. The cap and crown of each burner are secured with two screws. To separate the two pieces, lift the cap, turn it upside down, then undo the two fixing screws as shown in fig. 3. After cleaning, reassemble the two parts and refit the cap on its correct position on the burner. Wash the burner caps and crowns

FO2265

using hot soapy water, and remove marks with a mild paste cleaner. A well moistened soap impregnated steel wool pad can be used with caution, if the marks are particularly difficult to remove. After cleaning, be sure to wipe dry with a soft cloth.

Ignition electrode

The electric ignition is obtained through a ceramic "electrode" and a metal electrode (fig. 1 - letter B). Keep these components well clean, to avoid difficult lighting, and check that the burner crown holes are not obstructed.

Something Not Working?

If the hob is not working correctly, please carry out the following checks before contacting your local Service Force Centre.

SYMPTOM

 There is no spark when lighting the gas

SOLUTION

 Check that the unit is plugged in and the

electrical supply is switched on

 Check that the RCCB has not tripped (if fitted)

 Check the mains fuse has not blown

 Check the burner cap and crown have been

replaced correctly, e.g. after cleaning.

 The gas ring burns unevenly

 Check the main jet is not blocked and the

burner crown is clear of food particles.

 Check the burner cap and crown have been

replaced correctly, e.g. after cleaning.

If after all these checks, your hob still does not operate correctly, contact your local Service Force Centre.

Please note that it will be necessary to provide proof of purchase for any inguarantee service calls.

In-guarantee customers should ensure that the above checks have been made as the engineer will make a charge if the fault is not a mechanical or electrical breakdown.

+ 16 hidden pages