|
|
|
ITEM # _______________________________________________ |
|
|
|
|
MODEL # _____________________________________________ |
|
|
Warewashing |
PROJECT NAME # ______________________________________ |
||
|
66″ Single Tank Conveyor Dishwasher |
SIS # _________________________________________________ |
||
|
|
|
||
|
with Built In Hot Water Booster WT66 |
AIA # _________________________________________________ |
||
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
Main features |
|
|
|
|
||
|
|
|
• Built in hot water booster (top mounted in wash/rinse section). |
|
|
|
|
• Water booster temperature rise can be set on site during the installation of the |
|
|
|
|
machine. 40 °F rise (140 °F incoming water temperature), 70 °F rise (110 °F |
|
|
|
|
incoming water temperature) or |
|
|
|
|
100 °F rise (80 °F incoming water temperature). |
|
|
|
|
• Atmospheric booster system with air break. |
|
|
|
|
• Built in rinse booster pump guarantees constant rinse pressure. |
|
|
|
|
• Speed of conveyor can be set through the control panel by the operator. |
|
|
|
|
130 racks/hr or 200 racks/hr. |
|
|
|
|
• Large counter balanced inspection doors in pre wash and wash/rinse sections |
|
|
|
|
allow unrestricted all round access to the wash and rinse area. Door is insulated |
|
|
|
|
with injected foam. This adds strength as well as reduces noise and heat loss. |
|
|
|
|
• Large filters sloping towards the front to the smaller pressed filter box for quick |
|
|
|
|
removal. Filters feature holes smaller than the concave ant-block wash nozzles so |
|
|
|
|
large food cannot enter and block the wash system. Filters easy to remove from |
|
|
Warewashing |
|
pre wash as well as wash/rinse sections. |
|
|
66″ Single Tank Conveyor Dishwasher |
|
• Adjustable feet for full access underneath the machine for cleaning. |
|
|
with Built In Hot Water Booster WT66 |
|
• Push button self cleaning cycle of the wash and rinse zones for ease of “end of |
|
|
534090 (WT66BL208) 66″ Conveyor Dishwasher with |
|
day” cleaning. |
|
|
|
• Wash chamber without internal pipes and therefore no hidden dirt traps. |
||
|
Built in Booster. Left to Right - 208V |
|
||
|
|
• Pre wash chamber without internal pipes and therefore no hidden |
||
|
534091 (WT66BR208) 66″ Conveyor Dishwasher with |
|
||
|
|
dirt traps. |
||
|
Built in Booster. Right to Left - 208V |
|
||
|
|
• Self draining wash pumps provide maximum hygiene with no smells and all |
||
|
534092 (WT66BL240) 66″ Conveyor Dishwasher with |
|
||
|
|
wash and rinse zones drain automatically at the push of a button. |
||
|
Built in Booster. Left to Right - 240V |
|
||
|
|
• Powerful 0.5 HP pre-wash pump. |
||
|
534093 (WT66BR240) 66″ Conveyor Dishwasher with |
|
||
|
|
|
|
|
|
Built in Booster. Right to Left - 240V |
|
• Powerful 2 HP wash pump. |
|
|
|
|
• Heavy duty stainless steel wash pump (impeller and housing). |
|
|
|
|
||
|
Short Form Specification |
|
• Pre wash section uses cold water so food remains are not “baked” onto the |
|
|
|
plates. |
||
|
|
|
• Deep drawn pressed 26 gal wash tank with fully rounded corners, sloped |
|
|
Item No. ___________________________________ |
|
towards the drain to prevent dirt build up provides fast drainage in only a few |
|
|
|
minutes. Pressed wash tank with no welded points offer a guaranteed water |
||
|
Unit to be Electrolux WT66 Hot Water Sanitizing 66″ single tank conveyor |
|
tight solution. |
|
|
|
|
|
|
|
dishwasher with built in hot water booster. Electrical characteristics to be |
|
• Deep drawn pressed 11.8 gal pre wash tank with fully rounded corners. |
|
|
____ 208 V or ____ 240 V three phase operation. Unit to operate from ___ |
|
• Dishwasher structure is held together with a solid 2″ × 2″ Stainless steel tube |
|
|
left to right or ____ right to left. Unit to feature atmospheric built in booster |
|
sub-frame to provide long term sturdiness. |
|
|
system with built in rinse booster pump thus guaranteeing rinse pressure |
|
||
|
|
• All main components made in heavy duty anti-corrosive 304 type Stainless steel: |
||
|
during rinse cycle. Hot water booster temperature rise can be selected |
|
||
|
|
tanks, panels, pre wash, wash & rinse arms and caps, doors, front, handle, rear |
||
|
during installation from three options, 40 °F rise (140 °F incoming water |
|
||
|
|
and side-panels and rack transportation system. |
||
|
temperature), 70 °F rise (110 °F incoming water temperature) or 100 °F |
|
||
|
rise (80 °F incoming water temperature). Unit to include 22″ pre-wash zone. |
|
• Pre wash, wash and rinse arms can be easily removed for cleaning. |
|
|
Pre-wash zone with powerful 0.5 hp cold water pre wash. Unit to have two |
|
• IPX5 (NEMA4) water protection ensures no damage from cleaning. |
|
|
conveyor speeds which can be selected from the control panel by the |
|
||
|
|
• Autostart/stop ensures that the machine runs only when a rack is passing |
||
|
operator, 130 racks/hour or 200 racks/hour. Maximum water consumption |
|
||
|
at 200 racks/hour of only 83 gal/hour (0.4 gal/rack). Unit to feature large |
|
through it. This reduces both water and energy consumption. |
|
|
heat and noise insulated front counter balanced door in pre wash and |
|
• Internal curtains made of silastic material and are not affected by detergent or |
|
|
wash/rinse sections for easy access of internal components. Powerful 2 |
|
heat. |
|
|
HP wash pump and specially designed wash spray arms to guarantee |
|
||
|
|
• Electronic control panel features large display for reading of wash and rinse |
||
|
cleaning. Unit to feature as standard end of day self cleaning cycle. Drain |
|
||
|
|
temperatures. |
||
|
of water from the machine can be done through the control panel. Large |
|
||
|
|
|
|
|
|
deep drawn 26 gal wash tank for extended wash sessions. |
|
• Low water consumption. At 200 racks per hour, the machine uses only |
|
|
Covered by Electrolux Platinum Star® Service Program two-year parts |
|
83 gal/hr (0.4 gal/rack). |
|
|
|
|
|
|
|
and one-year labor warranty, installation start-up and performance check- |
|
• Machine predisposed for external detergent and rinse aid connections. |
|
|
up after one year from installation. |
|
Included Accessories |
|
|
|
|
||
|
|
|
||
|
|
|
• Vent cowls (left and right side). |
|
|
|
|
• One open sided dishwasher rack for trays. |
|
3048424 |
|
• Rack for cups. |
||
|
• Rack for dinner plates. |
|||
|
|
|
||
Approval: ___________________________________________ |
|
|
||
|
|
|
|
|
|
|
|
|
|
Electrolux Professional, Inc. www.electroluxusa.com/professional
3225 SW 42nd Street, Fort Lauderdale, Florida, 33312 • Telephone Number: 866-449-4200 • Fax Number: 954-327-6789
<![if ! IE]> <![endif]>″66 |
|
<![if ! IE]> <![endif]>WT66 oosterB aterW otH nI uiltB with Dishwasher Conveyor Tank Single |
<![if ! IE]> <![endif]>Warewashing |
|
|
Electric
Supply voltage: 534090 |
208V/3ph/60Hz |
534091 208V/3ph/60Hz
534092 240V/3ph/60Hz
534093 240V/3ph/60Hz
Dishwasher has three selectable hot water booster configurations according to inlet water supply temperature.
Dishwasher requires two separate electrical service connections. Connection 1 for Hot Water Booster; Connection 2 for running of the machine (wash pump, tank heat, conveyor drive motor, rinse booster pump, electronic control). Refer to the information below for Amp requirements.
Booster 40 °F rise Electrical Characteristics
Hot Water Booster Amp Load Connection 1:
208 V/3p/60Hz |
33.35A (12 kW) |
240 V/3p/60Hz |
28.9A (12 kW) |
Wash Pump, Tank heat Amp Load Connection 2:
208 V/3p/60Hz |
64A (21 kW) |
240 V/3p/60Hz |
57.5A (21 kW) |
Total Amp Load: 208 V/3p/60Hz |
97.4A (33 kW) |
240 V/3p/60Hz |
86.4A (33 kW) |
Booster 70 °F rise Electrical Characteristics
Hot Water Booster Amp Load Connection 1:
208 V/3p/60Hz |
50A (18 kW) |
240 V/3p/60Hz |
43.3A (18 kW) |
Wash Pump, Tank heat Amp Load Connection 2:
208 V/3p/60Hz |
64A (21 kW) |
240 V/3p/60Hz |
57.5A (21 kW) |
Total Amp Load: 208 V/3p/60Hz |
114A (39 kW) |
240 V/3p/60Hz |
100.8A (39 kW) |
Booster 100 °F rise Electrical Characteristics
Hot Water Booster Amp Load Connection 1:
208 V/3p/60Hz |
66.6A (24 kW) |
240 V/3p/60Hz |
57.7A (24 kW) |
Wash Pump, Tank heat Amp Load Connection 2:
208 V/3p/60Hz |
64A (21 kW) |
240 V/3p/60Hz |
57.5A (21 kW) |
Total Amp Load: 208 V/3p/60Hz |
130.6A (45 kW) |
240 V/3p/60Hz |
115.2A (45 kW) |
Warewashing
66″ Single Tank Conveyor Dishwasher
with Built In Hot Water Booster WT66
Water
Inlet Water supply pressure: |
22 – 102 psi (150 – 700 kPa) |
Inlet Cold Water Supply Temperature |
|
for pre wash section: |
39-59 °F (4-15 °C) |
Inlet Hot Water Supply Temperature for wash/rinse section (booster size can be set on site during installation):
140 °F (60 °C)
with booster set as 40 °F rise. 110 °F (44 °C)
with booster set as 70 °F rise. 80 °F (27 °C)
with booster set as 100 °F rise.
Inlet Water supply hardness: |
4 - 8 GPG (7-14 °fH) max |
Incoming Cold Water line size |
|
(pre wash): |
G 3/4″ |
Incoming Hot Water line size |
|
(wash/rinse section): |
G 3/4″ |
Drain line size (pre wash section): |
G 1-1/2″ |
Drain line size (wash/rinse section): |
G 1-1/2″ |
Water consumption: Gallons/hr: |
83.2 gal/hr (315 liters) |
Water consumption/rack: |
0.4 gal/rack (1.5 l/rack) |
Pre wash temperature: |
< 105 °F (<40 °C) |
Pre wash tank size: |
11.8 gal (45 liters) |
Pre wash pump power: |
0.5 hp (0,37 kW) |
Pre wash pump water flow: |
39 gal/min (150 l/min) |
Wash temperature: |
160 – 172 °F (71-78 °C) |
Wash tank size: |
26 gal (100 liters) |
Wash pump power: |
2 hp (1.5kW) |
Wash pump water flow: |
118.9 gal/min (450 l/min) |
Rinse temperature: |
180 – 194 °F (82-90 °C) |
Rinse pump power: |
0.4 hp (0.32 kW) |
Rinse pump water flow: |
1.32 gal/min (5 l/min) |
Hot water booster capacity: |
6.2 gal (24 liters) |
Initial fill Hot Water requirements: |
32.2 gal (124 liters) |
Initial fill Cold Water requirements: |
11.8 gal (45 liters) |
Exhaust Requirements
Unit supplied as standard with extended vent hoods (can be removed during installation if not required).
Exhaust extraction not more than 160 CFM
Refer to installation diagram for minimum exhaust hood installation height .
Key Information
Productivity racks per hour |
200 racks / 3600 dishes |
(max speed): |
(average 18 dishes per rack) |
Productivity racks per hour |
130 racks / 2340 dishes |
(min speed): |
(average 18 dishes per rack) |
Table to Table connection: |
66″ (1676 mm) |
Number of Tanks: |
1 |
Height with door open: |
83-7/16″ (2119 mm) |
Charging hole size (width): |
20-7/8″ (530 mm) |
Charging hole size (height): |
19-3/4″ (501 mm) |
Net weight: |
1012 lb (459 kg) |
Shipping weight: |
1210 lb (549 kg) |
Shipping width: |
74-7/16″ (1890 mm) |
Shipping depth: |
40-15/16″ (1040 mm) |
Shipping height: |
81-1/8″ (2060 mm) |
Shipping volume: |
143 cu.ft (4.05 m3) |
Noise level: |
<70 dBA |
Unit predisposed to accept external detergent dispensers, detergent probes and rinse aid dispensers.