Electrolux 318201808 User Manual

WARM & SERVE DRAWER INSTALLATION INSTRUCTIONS

D

A

F

E

C

B

WARNING

Canada United States

INSTALLATION AND SERVICE MUST BE PERFORMED

BY A QUALIFIED INSTALLER.

IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE.

READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

FOR YOUR SAFETY: Do not store or use gasoline or other

flammable vapors and liquids in the vicinity of this or any other appliance.

GENERAL INFORMATION: The Warm & Serve Drawer

can be used as a stand alone appliance or combine with a
built-in oven mounted above.

Warm & Serve Drawer Dimensions

NOTE: A 60" (152,4 cm) long cable is supplied with

the Warm & Serve Drawer.

Stand Alone Installation

60" (152,4
cm) Cord

IMPORTANT: The warmer drawer must be installed on

a leveled surface from left to right, rear to front and the
surface must be capable of supporting 100 lbs (45,4 Kg).

IMPORTANT: The Warm & Serve Drawer runs off a
single phase three-wire 120 volt, 60 hertz, AC only
electrical supply with ground.

Combination Warm & Serve Drawer/

Built-in Oven Installation

Caution: Two 3" (7,6 cm) wide X

3/4" (1,9 cm) thick planks have to
be install and they should be able to
support 200 pounds. (90,7 Kg)

Warm and Serve
Drawer

Warm and Serve
Cutout

Minimum distance to floor
4½" (11,4 cm)

FLOOR

A. HEIGHT B. WIDTH C. DEPTH

10 ¾" (27,3 cm) 29" (73,7 cm) 23

D. CUTOUT

HEIGHT
Min. 9
Max. 10 ¼" (26 cm) 28 ¾" (73 cm) 24" (61 cm)

7

/8" (25,1 cm) 28 ½" (72,4 cm) 23 5/8" (60 cm)

E. CUTOUT

WIDTH

3

/8" (59,4 cm)

F. CUTOUT

DEPTH

29½"

(74,9cm)

H* = 11 5/8" (29,5cm) Min. is a Critical
dimension and has to be respected.

J** = 3" (7,6cm) Max. Electrical Junction Box for wall oven
must be lower than warmer drawer cutout.

A. HEIGHT B. WIDTH C. DEPTH

3

10 ¾" (27,3 cm) 29" (73,7 cm) 23

D. CUTOUT

HEIGHT

Min. 9

7

/8" (25,1 cm) 28 ½" (72,4 cm) 24" (61 cm) 1 ¾" (4,4 cm)

E. CUTOUT

WIDTH

F. CUTOUT

/8" (59,4 cm)

DEPTH

Max. 10 ¼" (26 cm) 28 ¾" (73 cm)

Bottom of oven cutout

G. HEIGHT

Depends on critical

dimension H

Printed in the USA

P/N 318201808 (0901) Rev. C

English – pages 1-4

Español – páginas 5-8

Français – pages 9-12

1

WARM & SERVE DRAWER INSTALLATION INSTRUCTIONS

Important Notes to the Installer

1. Read all instructions contained in these installation
instructions before installing appliance.

2. Remove all packing material from appliance before
connecting the electrical supply.

3. Observe all governing codes and ordinances.

4. Be sure to leave these instructions with the consumer.

Important Note to the Consumer

Keep these instructions for future reference.

IMPORTANT SAFETY
INSTRUCTIONS

• Be sure your appliance is installed and plugged

into a 120 Volt grounded outlet.

• This appliance must be electrically grounded in

accordance with the National Electrical Code ANSI/
NFPA No. 70—latest edition in the United States,
or CSA C22.1, Part 1 in Canada, and local code
requirements.

Tools You Will Need

Phillips® Screwdriver
Pencil
Ruler or Tape Measure and Straight-edge
Hand Saw or Saber Saw
Spirit Level

2. Slide drawer into cutout opening until front frame of
drawer is flush against cabinet. Be careful not to pinch
electrical cord.

3. Remove the drawer as instructed in the Use & Care
Guide and secure drawer housing to cabinet using the
3 nickel-plated screws supplied (see Figure 2). Do not

overtighten screws.

4. The 60" (152,4 cm) appliance power cord can now be
connected into the 120 Volt outlet.

5. Proceed with mounting built-in oven above the drawer
(if applicable). Follow installation instructions provided
with built-in oven. Make sure to use anti-tip brackets
supplied with the built-in oven.

Use screws
supplied to attach
drawer to front of
cabinet.

Figure 2

Warm & Serve Drawer Installation

1. Locate the 2 anti-tip brackets supplied as shown on fig.

1.

c

/c 25 5/16"

(64,3 cm)

24" (61 cm) Max.

c

/c 12 21/32"

(32,15 cm)

23 5/8" (60 cm) Min.

Figure 1

2

30" WARMER DRAWER FRONT PANEL INSTALLATION INSTRUCTIONS

B

B

A

A

A

A

A

WARM & SERVE DRAWER INSTALLATION INSTRUCTIONS

Front Panel Installation instructions:

First, install the drawer handle (if applicable) on the
wood panel.

1. Remove the 5 screws located at position
A which are fixing the drawer mounting
panel to the drawer interior panel.

2. Place the drawer mounting panel on the
inside of the drawer wood panel as per fig­ure 2. Fix the drawer wood panel (supplied
by the customer) to the drawer mounting
panel using the 4 wood screws supplied at
location B.

3. Reinstall this new assembly wood &
mounting drawer panel to the drawer
interior panel.

Drawer

Mounting

Panel

Drawer

Interior Panel

Drawer Wood Panel

(supplied by the customer)

Figure 1

Drawer Wood Panel
(supplied by the customer)

30’’

Drawer Mounting Panel

Note: Wood panel should be ½’’ min. thick.

Center line

Figure 2

11¼’’

3

WARM & SERVE DRAWER INSTALLATION INSTRUCTIONS

Electrical connection

IMPORTANT Please read carefully.

For personal safety, this appliance must be properly
grounded.

The power cord of this appliance is equipped with a
3-prong (grounding) plug which mates with a standard
3-prong grounding wall receptacle to minimize the
possibility of electric shock hazard from the appliance.

The wall receptacle and circuit should be checked by a
qualified electrician to make sure the receptacle is properly
grounded.

Where a standard 2-prong wall receptacle is installed, it is
the personal responsibility and obligation of the consumer
to have it replaced by a properly grounded 3-prong wall
receptacle.

Do not, under any circumstances, cut or remove the
third (ground) prong from the power cord.

Disconnect electrical supply cord from wall

receptacle before servicing cooktop.

Model and Serial Number Location

The serial plate is located as shown below.

When ordering parts for or making inquiries about your
Warm & Serve Drawer, always be sure to include the
model and serial numbers and a lot number or letter
from the serial plate on your Warm & Serve Drawer.

Serial

Plate Location

Preferred Method

Grounding type
wall receptacle

Do not, under any
circumstances, cut,
remove, or bypass
the grounding
prong.

Power supply cord with
3-prong grounding plug.

Combination Warm & Serve Drawer and
Cooktop Installation

Cooktop
Cutout

Warmer
Drawer
Cutout

You can install the warmer drawer in combination
with an electric or gas cooktop. You must follow the
specifications from the installation instructions of the
cooktop to avoid interference with the gas or electric
installation.

4