Electrolux 30 User Manual [en, es, fr]

MICROWAVE OVEN INSTALLATION INSTRUCTIONS
INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER.
IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE.
READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
The electrical requirements for this oven are 115-120 volts AC, 15 amps or larger.
Printed in United States
IMPORTANT - PLEASE READ AND FOLLOW
• Be sure to DISCONNECT THE PLUG of the microwave oven from the electrical outlet before installing the built-in trim kit. Remove the turntable from the oven cavity.
Because the kit includes metal parts, caution should be used in handling and installation to avoid the possibility of injury.
• Do not remove permanently affixed labels, warnings, or plates from the product. This may void the warranty.
• Please observe all local and national codes and ordinances.
The installer should leave these instructions with the consumer who should retain for local inspector ’s use and for
future reference.
PARTS INCLUDED IN THE KITS
1) FRONT FRAME ASSEMBLY QTY 1
2) BOTTOM DUCT ASSEMBLY QTY 1
3) SCREW A (1 ³₁₆" LENGTH) QTY 2
4) SCREW B (1 ³₄" LENGTH) QTY 4
MICROWAVE OVEN INSTALLATION INSTRUCTIONS
E2
MICROWAVE OVEN INSTALLATION INSTRUCTIONS
BASIC SPECIFICATIONS
Re fer to Illus tration 1. A ll d imens ions are i n in ches (cm ).
Illustration 1
1. Provide an opening in the wall or cabinet as indicated in Illustration 1. The depth should be a minimum of 20" (50.8 cm). The floor of the opening should be constructed of plywood strong enough to support the weight of the microwave oven (about 100 lbs.) and should be level for proper operation of the oven.
NOTE: While the proper functioning of the microwave
oven does not require that the opening be enclosed (with sides, ceiling and rear partition), this may be required
by local code, and it is suggested that the local code be checked for any such requirement.
2. Outlet should NOT be in the shaded area as indicated on Illustration 1. At the rear of the opening, provide a 3­pronged, polarized, electrical outlet, 115-120 volt AC, 15 amp or larger.
3. Minimum required distance between the microwave oven and the wall oven should be 2-inches.
A
B
C
D
E
F
6" (15.2 cm)
4" (10.2 cm)
4" (10.2 cm)
installation over an electric wall
oven 2" (5.1 cm) minimum gap
H
G
Product overlap
7/8" (2.2 cm)
I
J
PRODUCT DIMENSIONS
EI 30M 045 GS MIC ROWA VE OVE N / EI30 M04 5TK TR IM KIT
A B C D E F G
30" (76.2 cm)
18 ¹₁₆" (45.9 cm) 2 ⁵₁₆" (5.9 cm)
24" (60.96 cm)
13 ³₈" (33.9 cm) 15 ³₄" (40.0 cm)
min. 30" (76.2 cm)
EI 27M0 45G S M ICR OWAV E O VEN / EI2 7M0 45TK TRI M K IT
A B C D E F G
27" (68.6 cm)
18 ¹₁₆" (45.9 cm) 2 ⁵₁₆" (5.9 cm)
24" (60.96 cm)
13 ³₈" (33.9 cm) 15 ³₄" (40.0 cm)
min. 27" (68.6 cm)
CUTOUT DIMENSIONS
min. H ma x. min. I ma x. J
25 ¹₄" (64.14 cm) 25 ³₈" (64.5 cm) 16 ¹₄" (41.3 cm) 16 ³₈" (41.6 cm)
min. 20" (50.8 cm)
BASIC SPECIFICATIONS
OVEN INTERIO R
ELEC TRI CAL
REQUI REMEN TS
APPROX IMATE
SHIPPIN G WT.
MA X AMP. US AGE
WIDT H HE
IG HT D EPTH OVE RALL
120VAC/60 Hz (UL) 120VAC/60 Hz (CSA)
46 lbs. (20.9 kg)
1.5 KW 13.0 amps (UL)
1.50 KW 13 (CSA)
17 ³₈" (44.1 cm) 10 ¹⁄₂" (26.6 cm) 18 ⁵₈" (47.3 cm)
2.0 cu. ft.
Illustration 1
E3
MICROWAVE OVEN INSTALLATION INSTRUCTIONS
BOTTOM DUCT ASSEMBLY
1. Place the bottom duct in the opening and center. When the Bottom Duct Assembly is in the opening correctly, the flange will be tight against the lower edge of the opening. See Illustration 2.
Illustration 2 Illustration 3
Illustration 4 Illustration 5
SCREW A
SCREW A
2. Secure the Bottom Duct Assembly with the two (1 ³₁₆") scre ws A. IM P O RTANT: Secure s crews to the inside cabinet. See Illustration 3.
UNIT INSTALLATION
1. Place the oven adjacent to the wall or cabinet opening. Plug the power cord into the electrical outlet. Carefully guide the oven into the prepared opening. Slide the oven on the Bottom Duct Assembly. Avoid pinching the cord between the oven and the wall. Adjust the position of the oven so that it will rest on the Bottom Duct Assembly, but not fully pushed in. See Illustration 4.
2. Locate tabs on the built in trim kit to the slots on control panel. Snap the built in trim kit into the control panel to lock in place. See Illustration 5.
SHAPE ON
BOTTO M
MICROWAVE OVEN INSTALLATION INSTRUCTIONS
3. Push the position of the oven into the cabinet so that the feet of the oven are fitted into the recesses of the Bottom Duct Assembly. Make sure that the kit now rests flush with the cabinet. See Illustration 6.
Illustration 6
Illustration 7
SCREW B
SCREW B
SCREW B
SCREW B
4. Adjust the frame so that the gap around the top of the door and frame is even. Pre-drill 4 holes using an ¹⁄₈" bit, using the kit to guide the holes. Attach the built-in trim kit frame with four screws B to the cabinet. See Illustration 7.
IMPORTANT: Install top left mounting screw first in order
to secure proper alignment of frame to oven face.
TINSEB490MRR1
Loading...
+ 9 hidden pages