Electrocube 650 SERIES Catalog Page

METALLIZED POLYCARBONATE CAPACITORS

®

650 SERIES

This metallized polycarbonate
capacitor series exhibits superior electrical
characteristics over an extremely wide
temperature range. Their miniature size,
high Q, excellent IR and capacitance
stability make them ideally suited to
filter network and other low-loss high
frequency applications.

A wide variety of sizes and configu­rations are available: axial-lead wrap
and fill (in oval and round shapes) and
rectangular epoxy case (axial and
radial leads).

All capacitors feature extended foil

construction and standard tin-coated

copper-clad steel leads. Nickel, copper,
dumet and other special leads are
available.

Protective clear wrap is offered on
all wrap and fill units. Please add .010”
to maximum T and W dimension for
protective clear wrap.

The potting material and endfills
of Electrocube’s capacitors meet or
exceed the flammability requirments
of UL94VO.

Dimensional variations for all
MFD values are available with the
same volume to meet your design
requirements.

SPECIFICATIONS

Temperature: -55°C to +125°C.
Dielectric Strength: Will withstand 200% at rated voltage

and 25°C for a period not to exceed 1 minute; current limited
to 5 mA.

Life Test: Will withstand 140% rated voltage for 250 hours at +125°C,

with not more than 1 failure in 12 permitted.

Dissipation Factor: Shall not exceed 0.3% at 25°C.
Dielectric Absorption: Shall not exceed 0.2% at 25°C per

MIL-C-19978.

Acceptance Criteria: Measurement frequency for capacitance

and dissipation factor shall be 1000 Hz for values to 1 mfd;
120 Hz for values of 1 mfd and over.

Insulation Resistance: At rated voltage or 500V, whichever

is less, units shall meet the minimum values below:

TYPICAL DIELECTRIC CHARACTERISTIC CURVES

ANCE CHANGE

% CAPACIT

NOTES:

The following capacitor series (625B, 625C, 625D) are not recommended
for new design. For technical data or alternate design and application
information, consult factory.

For information regarding insulating sleeves, mountings, special terminals,
non-standard leads, circuit connections and other hardware, please
consult factory.

For styles and ratings not shown, or for unusual requirements necessitated
by special circuit applications (including higher IR or lower DF), consult
the factory direct.

All Electrocube film capacitors have endfills and tape that
meet or exceed the flammability requirements of UL94V0.

1307 S. Myrtle Ave. • Monrovia, CA 91016 • TEL: [phone] • FAX: [phone]

®

e-mail: [e-mail] • Internet: www.electrocube.com • (IR: 9/99)

% DISSIPATION FACTOR

ARADS)

INSULATION RESISTANCE

(MEGOHMS TIMES MICROF

METALLIZED POLYCARBONATE CAPACITORS

®

SERIES NO. DESCRIPTION

650 SERIES

650B

650C

650D

FLAME RETARDANT
WRAP AND FILL, OVAL

FLAME RETARDANT
WRAP AND FILL, FLAT

FLAME RETARDANT
WRAP AND FILL, ROUND

FLAME RETARDANT

652A

EPOXY CASE,
RECTANGULAR
RADIAL LEADS

FLAME RETARDANT

653A

EPOXY CASE,
RECTANGULAR
AXIAL LEADS

1307 S. Myrtle Ave. • Monrovia, CA 91016 • TEL: [phone] • FAX: [phone]

®

e-mail: [e-mail] • Internet: www.electrocube.com • (IR: 9/99)

METALLIZED POLYCARBONATE

®

650B SERIES

WRAP AND FILL

OVAL CONFIGURATION

For max. T, W and L dimensions, allow +.050”.

LEAD LENGTH: 2.0” ± .50”

50 VOLT DC 100 VOLT DC 200 VOLT DC

DIMENSIONS

MFD PART NO. T W L

.0010 650B1A102* .09 .18 .40 26 650B1B102* .09 .18 .40 26 650B1C102* .09 .18 .40 26
.0018 650B1A182* .09 .18 .40 26 650B1B182* .09 .18 .40 26 650B1C182* .09 .18 .40 26
.0022 650B1A222* .09 .18 .40 26 650B1B222* .09 .18 .40 26 650B1C222* .09 .18 .40 26
.0027 650B1A272* .09 .18 .40 26 650B1B272* .09 .18 .40 26 650B1C272* .09 .18 .40 26
.0033 650B1A332* .09 .18 .40 26 650B1B332* .09 .18 .40 26 650B1C332* .09 .18 .40 26
.0039 650B1A392* .09 .18 .40 26 650B1B392* .09 .18 .40 26 650B1C392* .09 .18 .40 26
.0047 650B1A472* .09 .18 .40 26 650B1B472* .09 .18 .40 26 650B1C472* .09 .18 .40 26
.0056 650B1A562* .09 .18 .40 26 650B1B562* .09 .18 .40 26 650B1C562* .09 .18 .40 26
.0068 650B1A682* .09 .18 .40 26 650B1B682* .09 .18 .40 26 650B1C682* .13 .23 .40 26
.0082 650B1A822* .09 .18 .40 26 650B1B822* .09 .18 .40 26 650B1C822* .11 .21 .40 26
.010 650B1A103* .09 .18 .40 26 650B1B103* .09 .18 .40 26 650B1C103* .12 .22 .40 26
.012 650B1A123* .09 .18 .40 26 650B1B123* .09 .18 .40 26 650B1C123* .14 .23 .40 26
.015 650B1A153* .09 .18 .40 26 650B1B153* .09 .18 .40 26 650B1C153* .13 .22 .40 26
.018 650B1A183* .09 .18 .40 26 650B1B183* .09 .18 .40 26 650B1C183* .14 .24 .40 26
.022 650B1A223* .09 .18 .40 26 650B1B223* .09 .18 .40 26 650B1C223* .16 .25 .40 26
.027 650B1A273* .09 .18 .40 26 650B1B273* .10 .18 .40 26 650B1C273* .11 .21 .53 26
.033 650B1A333* .09 .18 .40 26 650B1B333* .12 .22 .40 26 650B1C333* .13 .22 .53 26
.039 650B1A393* .09 .18 .40 26 650B1B393* .12 .22 .40 26 650B1C393* .14 .23 .53 26
.047 650B1A473* .09 .18 .40 26 650B1B473* .13 .23 .40 26 650B1C473* .15 .25 .53 26
.056 650B1A563* .10 .19 .40 26 650B1B563* .15 .24 .40 26 650B1C563* .17 .26 .53 24
.068 650B1A683* .11 .20 .40 26 650B1B683* .16 .26 .40 26 650B1C683* .19 .28 .53 24
.082 650B1A823* .11 .21 .40 26 650B1B823* .18 .27 .40 26 650B1C823* .21 .30 .53 24
.10 650B1A104* .12 .21 .40 26 650B1B104* .13 .22 .53 26 650B1C104* .23 .32 .53 24
.12 650B1A124* .13 .22 .40 26 650B1B124* .14 .24 .53 26 650B1C124* .25 .35 .53 24
.15 650B1A154* .15 .24 .40 26 650B1B154* .16 .25 .53 24 650B1C154* .30 .39 .53 24
.18 650B1A184* .10 .20 .53 26 650B1B184* .18 .27 .53 24 650B1C184* .25 .34 .65 24
.22 650B1A224* .12 .21 .53 26 650B1B224* .20 .29 .53 24 650B1C224* .27 .37 .65 24
.27 650B1A274* .13 .22 .53 26 650B1B274* .22 .31 .53 24 650B1C274* .26 .35 .78 24
.33 650B1A334* .14 .24 .53 26 650B1B334* .24 .34 .53 24 650B1C334* .29 .38 .78 24
.39 650B1A394* .16 .25 .53 24 650B1B394* .27 .36 .53 24 650B1C394* .31 .41 .78 22
.47 650B1A474* .17 .27 .53 24 650B1B474* .23 .32 .65 24 650B1C474* .35 .44 .78 22
.56 650B1A564* .19 .28 .53 24 650B1B564* .25 .35 .65 24 650B1C564* .34 .43 .90 22
.68 650B1A684* .21 .30 .53 24 650B1B684* .24 .33 .78 24 650B1C684* .27 .44 1.15 22
.82 650B1A824* .23 .33 .53 24 650B1B824* .26 .36 .78 24 650B1C824* .31 .47 1.15 22

1.0 650B1A105* .26 .35 .53 24 650B1B105* .29 .39 .78 24 650B1C105* .34 .51 1.15 22

1.2 650B1A125* .22 .32 .65 24 650B1B125* .32 .42 .78 22 650B1C125* .38 .55 1.15 20

1.5 650B1A155* .25 .35 .65 24 650B1B155* .32 .41 .90 22 650B1C155* .43 .60 1.15 20

1.8 650B1A185* .28 .37 .65 24 650B1B185* .35 .45 .90 22 650B1C185* .48 .64 1.15 20

2.0 650B1A205* .25 .34 .78 24 650B1B205* .27 .44 1.15 22 650B1C205* .51 .67 1.15 20

2.5 650B1A255* .28 .38 .78 24 650B1B255* .35 .44 1.15 22 650B1C255* .50 .66 1.40 20

3.0 650B1A305* .31 .40 .78 22 650B1B305* .35 .51 1.15 20 650B1C305* .49 .66 1.65 20

3.5 650B1A355* .34 .43 .78 22 650B1B355* .38 .55 1.15 20 650B1C355* .53 .70 1.65 20

4.0 650B1A405* .32 .41 .90 22 650B1B405* .41 .58 1.15 20 650B1C405* .52 .69 1.90 20

4.5 650B1A455* .34 .43 .90 22 650B1B455* .44 .60 1.15 20 650B1C455* .56 .73 1.90 20

5.0 650B1A505* .26 .43 1.15 22 650B1B505* .46 .63 1.15 20 650B1C505* .59 .76 1.90 20

6.0 650B1A605* .29 .46 1.15 22 650B1B605* .51 .68 1.15 20 650B1C605* .65 .82 1.90 20

8.0 650B1A805* .34 .51 1.15 22 650B1B805* .52 .69 1.40 20 650B1C805* .76 .93 1.90 20

10.0 650B1A106* .39 .56 1.15 20 650B1B106* .53 .69 1.65 20 650B1C106* .86 1.03 1.90 20

12.0 650B1A126* .43 .60 1.15 20 650B1B126* .58 .75 1.65 20 650B1C126* - - - -

15.0 650B1A156* .49 .66 1.15 20 650B1B156* .60 .77 1.90 20 650B1C156* - - - -

18.0 650B1A186* .58 .68 1.15 20 650B1B186* .66 .83 1.90 20 650B1C186* - - - -

20.0 650B1A206* .50 .67 1.40 20 650B1B206* .70 .87 1.90 20 650B1C206* - - - -

30.0 650B1A306* .56 .72 1.65 20 650B1B306* - - - - 650B1C306* - - - -

40.0 650B1A406* .65 .82 1.65 20 650B1B406* - - - - 650B1C406* - - - -

50.0 650B1A506* .74 .90 1.65 20 650B1B506* - - - - 650B1C506* - - - -

*Add tolerance designator to complete part number: F = ±1%, G = ±2%, J = ±5%, K = ±10%, M = ±20%

LEAD

SIZE SIZE SIZE

(AWG)

PART NO. T W L

DIMENSIONS

LEAD

(AWG)

PART NO. T W L

DIMENSIONS

LEAD

(AWG)

1307 S. Myrtle Ave. • Monrovia, CA 91016 • TEL: [phone] • FAX: [phone]

®

e-mail: [e-mail] • Internet: www.electrocube.com • (A:8/00 )

METALLIZED POLYCARBONATE

®

650B SERIES

WRAP AND FILL

OVAL CONFIGURATION

For max. T, W and L dimensions, allow +.050”.

LEAD LENGTH: 2.0” ± .50”

400 VOLT DC 600 VOLT DC 1000 VOLT DC

DIMENSIONS

MFD PART NO. T W L

.0010 650B1E102* .09 .18 .40 26 650B1F102* .09 .18 .40 26 650B1G102* - - - ­.0018 650B1E182* .09 .18 .40 26 650B1F182* .10 .20 .40 26 650B1G182* - - - -
.0022 650B1E222* .10 .19 .40 26 650B1F222* .12 .21 .40 26 650B1G222* - - - -
.0027 650B1E272* .11 .20 .40 26 650B1F272* .09 .18 .53 26 650B1G272* - - - -
.0033 650B1E332* .12 .22 .40 26 650B1F332* .09 .18 .53 26 650B1G332* - - - -
.0039 650B1E392* .13 .23 .40 26 650B1F392* .10 .19 .53 26 650B1G392* - - - -
.0047 650B1E472* .15 .24 .40 26 650B1F472* .11 .21 .53 26 650B1G472* - - - -
.0056 650B1E562* .10 .20 .56 26 650B1F562* .13 .22 .53 24 650B1G562* - - - -
.0068 650B1E682* .11 .21 .56 26 650B1F682* .14 .24 .53 24 650B1G682* - - - -
.0082 650B1E822* .13 .22 .56 26 650B1F822* .16 .26 .53 24 650B1G822* - - - -
.010 650B1E103* .14 .23 .56 26 650B1F103* .18 .28 .53 24 650B1G103* - - - -
.012 650B1E123* .15 .25 .56 24 650B1F123* .20 .30 .53 24 650B1G123* - - - -
.015 650B1E153* .17 .27 .56 24 650B1F153* .23 .33 .53 24 650B1G153* - - - -
.018 650B1E183* .19 .29 .56 24 650B1F183* .20 .29 .68 24 650B1G183* - - - -
.022 650B1E223* .21 .31 .56 24 650B1F223* .22 .32 .68 24 650B1G223* - - - -
.027 650B1E273* .24 .33 .56 24 650B1F273* .21 .30 .78 24 650B1G273* - - - -
.033 650B1E333* .26 .36 .56 24 650B1F333* .24 .33 .78 24 650B1G333* - - - -
.039 650B1E393* .23 .32 .69 24 650B1F393* .26 .35 .78 24 650B1G393* - - - -
.047 650B1E473* .25 .35 .69 24 650B1F473* .29 .39 .78 24 650B1G473* - - - -
.056 650B1E563* .28 .37 .69 24 650B1F563* .32 .42 .78 22 650B1G563* - - - -
.068 650B1E683* .26 .35 .81 24 650B1F683* .32 .41 .95 22 650B1G683* - - - -
.082 650B1E823* .29 .38 .81 24 650B1F823* .25 .42 1.17 22 650B1G823* - - - -
.10 650B1E104* .32 .41 .81 24 650B1F104* .29 .24 1.17 22 650B1G104* - - - -
.12 650B1E124* .35 .45 .81 22 650B1F124* .32 .48 1.17 22 650B1G124* - - - -
.15 650B1E154* .35 .44 .95 22 650B1F154* .38 .54 1.17 20 650B1G154* - - - -
.18 650B1E184* .38 .48 .95 22 650B1F184* .41 .57 1.17 20 650B1G184* - - - -
.22 650B1E224* .32 .49 1.21 22 650B1F224* .46 .62 1.17 20 650B1G224* - - - -
.27 650B1E274* .36 .52 1.21 22 650B1F274* .45 .61 1.45 20 650B1G274* - - - -
.33 650B1E334* .40 .57 1.21 20 650B1F334* .50 .67 1.45 20 650B1G334* - - - -
.39 650B1E394* .44 .61 1.21 20 650B1F394* .49 .65 1.70 20 650B1G394* - - - -
.47 650B1E474* .49 .66 1.21 20 650B1F474* .49 .66 1.90 20 650B1G474* - - - -
.56 650B1E564* .54 .71 1.21 20 650B1F564* .54 .71 1.90 20 650B1G564* - - - -
.68 650B1E684* .52 .69 1.46 20 650B1F684* .61 .78 1.90 20 650B1G684* - - - -
.82 650B1E824* .52 .68 1.72 20 650B1F824* .68 .84 1.90 20 650B1G824* - - - -

1.0 650B1E105* .52 .69 1.96 20 650B1F105* .76 .93 1.90 20 650B1G105* - - - -

1.2 650B1E125* .58 .78 1.96 20 650B1F125* .84 1.00 1.90 20 650B1G125* - - - -

1.5 650B1E155* .65 .82 1.96 20 650B1F155* .95 1.11 1.90 20 650B1G155* - - - -

1.8 650B1E185* .72 .89 1.96 20 650B1F185* - - - - 650B1G185* - - - -

2.0 650B1E205* .76 .93 1.96 20 650B1F205* - - - - 650B1G205* - - - -

2.5 650B1E255* - - - - 650B1F255* - - - - 650B1G255* - - - -

3.0 650B1E305* - - - - 650B1F305* - - - - 650B1G305* - - - -

3.5 650B1E355* - - - - 650B1F355* - - - - 650B1G355* - - - -

4.0 650B1E405* - - - - 650B1F405* - - - - 650B1G405* - - - -

4.5 650B1E455* - - - - 650B1F455* - - - - 650B1G455* - - - -

5.0 650B1E505* - - - - 650B1F505* - - - - 650B1G505* - - - -

6.0 650B1E605* - - - - 650B1F605* - - - - 650B1G605* - - - -

8.0 650B1E805* - - - - 650B1F805* - - - - 650B1G805* - - - -

10.0 650B1E106* - - - - 650B1F106* - - - - 650B1G106* - - - -

12.0 650B1E126* - - - - 650B1F126* - - - - 650B1G126* - - - -

15.0 650B1E156* - - - - 650B1F156* - - - - 650B1G156* - - - -

18.0 650B1E186* - - - - 650B1F186* - - - - 650B1G186* - - - -

20.0 650B1E206* - - - - 650B1F206* - - - - 650B1G206* - - - -

30.0 650B1E306* - - - - 650B1F306* - - - - 650B1G306* - - - -

40.0 650B1E406* - - - - 650B1F406* - - - - 650B1G406* - - - -

50.0 650B1E506* - - - - 650B1F506* - - - - 650B1G506* - - - -

*Add tolerance designator to complete part number: F = ±1%, G = ±2%, J = ±5%, K = ±10%, M = ±20%

LEAD

SIZE SIZE SIZE

(AWG)

PART NO. T W L

DIMENSIONS

LEAD

(AWG)

PART NO. T W L

DIMENSIONS

PLEASE CONSULT FACTORY

LEAD

(AWG)

1307 S. Myrtle Ave. • Monrovia, CA 91016 • TEL: [phone] • FAX: [phone]

®

e-mail: [e-mail] • Internet: www.electrocube.com • (IR: 9/99)