USER MANUAL
PREMIUM LOW ENERGY COMPRESSOR
DEHUMIDIFIER WITH DIGITAL HUMIDISTAT
AND AIR PURIFIER
CD12LE – 12 litres per day
CD20LE – 20 litres per day
Thank you for choosing electriQ.
Please read this user manual before using this innovative
Dehumidier and keep it safe for future reference
Visit our page www.electriQ.co.uk for our entire range of Intelligent Electricals
CONTENTS
SAFETY INSTRUCTIONS 2
INSTALLATION 5
PARTS 6
CONTROL PANEL 7
QUICK REFERENCE GUIDE 8
POSITIONING 11
WATER DRAINAGE 12
CARE AND MAINTENANCE 12
TROUBLESHOOTING 14
TECHNICAL DATA 15
Carefully read the instructions before operating the unit
This appliance is for indoor use only and intended for use in a domestic
environment only. Any other use is not recommended by the manufacturer and
may cause re, electrical shocks or other injury to user or property.
Rating: This unit must be only connected to a 220-240 V / 50 Hz earthed outlet.
Installation must be in accordance with regulations of the country where the unit is
used.
If you are in any doubt about the suitability of your electrical supply have it
checked and if necessary, modied by a qualied electrician.
This dehumidifier has been tested and is safe to use. However, as with any
electrical appliance - use it with care.
Disconnect the power before dismantling, assembling or cleaning.
Avoid touching any moving parts of the appliance.
Never insert ngers, pencils or any other objects though the guard
This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities. It is also not intended for use by those
with a lack of experience and knowledge, unless they have been given supervision
or instruction concerning the use of the appliance by a person responsible for their
safety.
Do not leave children unsupervised with this appliance.
Do not clean the unit by spraying it or immersing it in water.
Never connect the unit to an electrical outlet using an extension cord. If a power
outlet is not available, one should be installed by a qualied electrician.
Never operate this appliance if the cord, power adapter or plug is damaged.
Ensure the power cord is not stretched or exposed to sharp objects/edges.
A damaged power supply cord should be replaced by the manufacturer or a
qualied electrician in order to avoid a hazard.
Any service other than regular cleaning or lter replacement should be performed
by an authorized service representative. Failure to comply could result in a voided
warranty.
Do not use the appliance for any purpose other than its intended use.
Do not tilt the unit while in use. The unit is design to work only in vertical position.
This dehumidifier must always be stored and transported upright, otherwise
irreparable damage may be caused to the compressor; if in doubt we suggest
waiting at least 24 hours before starting the unit.
Avoid restarting the dehumidier unless 5 minutes have passed since being turned
off. This prevents damage to the compressor.
Never use the plug as a switch to start or turn off the dehumidifier. Use the
provided ON/OFF switch located on the control panel.
Always place the unit on a dry and stable surface.
The appliance should not be installed in laundry or wet rooms where the humidity
is higher than 85% RH
Do not dry laundry above the unit to prevent water entering the dehumidier. Place
the laundry at least 1 meter away from your dehumidier.
IMPORTANT
SAFETY INSTRUCTIONS
02
The appliance must be placed in a room without sources of ignition (for example:
open ames, an operating gas appliance or an operating electric heater).
R290 refrigerant gas complies with European environmental directives.
R290 has a low GWP (Global Warming Potential) of 3.
The CD12LE contains about 60g of R290 refrigerant gas.
The CD20LE contains about 75g of R290 refrigerant gas.
Do not use or store the CD20LE in an unventilated space with an area smaller
than 4.1m2 per unit.
Do not use or store the CD12LE in an unventilated space with an area smaller
than 2.6m2 per unit.
If the appliance is installed, used or stored in an unventilated room, the room must
be such as to prevent stagnation of possible leaks of refrigerant gas as there
could be a danger of re or explosion should the refrigerant come into contact with
electric heaters, stoves or other sources of ignition.
Refrigerant gas may be odourless.
Do not use the product and contact the retailer for advice, if damage has occurred
to the unit which may have compromised the refrigerant system.
Any repairs or maintenance must only be carried out on the unit by a suitably
qualied engineer. Before opening and servicing the unit the authorized engineer
must be in possession of a copy of the manufacturer’s service manual and
must follow the safety information contained within it to ensure all hazards are
minimized.
The refrigerant system should not be perforated or punctured.
Do not place the unit next to heat sources (e.g. electrical res, replaces, etc.)
Avoid mishandling the dehumidifier. Dropping, throwing the unit can cause
damage to its internals and increases the risks of operating it.
Do not store or use gasoline, petrol, paint, solvents or other ammable vapours or
liquids in the vicinity of this dehumidier or any other appliance.
This dehumidier must not be used in spaces where there is a high concentration
of gases, solvent or other volatile organic compounds; in very dusty environments;
in any domestic, commercial or industrial environment where the air composition
is ammable.
Do not cover or restrict the airow from the outlet or inlet grills. Do not operate and
follow troubleshoot procedure if the self-opening louvers do not open on power on.
For maximum performance the minimum distance from a wall or objects should be
20 cm
Keep the lters or grills of the unit clean. Under normal conditions, lters or grills
should only need cleaning once every three weeks (approximately).
Since the filters remove airborne particles, more frequent cleaning maybe
necessary, depending on the air quality. Vacuum both mesh and optional carbon
lters and wash the mesh lters with hot soapy water and dry them before placing
them back in the unit.
ENERGY SAVING AND UNIT SAFETY PROTECTION TIPS
03
QUICK VISUAL SAFETY GUIDE ON WHERE OR WHEN NOT TO USE YOUR
DEHUMIDIFIER
Exposed to the
weather outdoors
Near water If the power cable
wires are frayed or cut
Where small children
may be left
unattended
If an extension lead
may become
overloaded
Where the power cable
may be damaged
On a slope or uneven
surface
Where there is risk
of re or close to a
naked ame
Where it may be
damaged by
chemicals
Where there is a risk
or interference by
foreign objects
This product is not
made for DIY repair
If there is a risk
of water faling on
the unit
04
INSTALLATION
Remove any water from within the water tank before starting the unit. In order to
save energy do not open windows or doors while the unit is running. Place the unit
on a hard / at surface. On rst use run the unit continuously for 24 hrs.
TO REDUCE NOISE LEVELS:
Place a piece of carpet or a rubber mat under the unit to reduce any vibrations while
the unit is running.
The CD12LE and CD20LE dehumidifiers use compressor technology to extract
water from the environment. Compressor dehumidifiers are ideal for normal
domestic or office environments which are heated during the winter months and
maintain a temperature above 12-15oC.
The dehumidiers are easy to move around on castors and are designed to extract
unwanted humidity while saving money due to their power saving logic. They
feature an intelligent humidistat where the desired relative humidity can be adjusted
in increments of 5% between 40 and 80% ensuring your room is not dried too much
and power is not wasted.
FEATURES
Your dehumidifier belongs to the electriQ low energy premium dehumidifiers
featuring low power consumption, power saving logic and advanced air purication
option.
Easy to use controls
Low energy only uses a fraction of the electricity of similar dehumidiers
Great for up to 3 bed (CD12LE) and 5 bed (CD20LE) houses
Cost effective way to combat mould, condensation and damp
Dries laundry more efciently than a tumble dryer
Designed to complement any modern space
Low and High fan speed selection for best balance between running quiet and
maximum water extraction
Anti-dust self-closing oscillating louvres for improved air ow
Castors for improved mobility
Intelligent CPU controlled digital humidistat with 35-80% RH and room humidity
display
24 hours start / stop timer
Tank operation or permanent drainage option with splash proof tank
Tank full alarm & auto-stop function
Air purier function with UV sterilisation
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
05
PARTS
8. Air inlet
11. Water tank
1. Louvers
3. Air outlet
4. Humidity
indicator light
6. Control Panel
2. Handle
5. Wheels
7. Pre-lter/activated
Carbon lter
9. Continuous
Drain Port
10. Back Cover
12. Power cord
OPTIONAL
Activated carbon lter (Optional)
06
HIGH
LOW
SMART
AIR PURIFIER
OPERATION
TANK FULL
DEFROST
MODE
POWER
UV
HUMIDITY
INDICATOR
LIGHT
TIMER OSC
HIGH
LOW
SMART
AIR PURIFIER
OPERATION
TANK FULL
DEFROST
MODE
POWER
UV
CONTROL PANEL
On/Off
Water full indicator
Defrost indicator
Humidity Indicator Down Up Mode
Timer
Oscillation Power
POWER
POWER
Turn the appliance on/off
MODE Button
Select the function of the unit between: SMART / HIGH / LOW /
and FAN. The LED’s next to the button will show which mode is
selected.
SMART MODE: The unit will default to SMART mode the rst time
it is switched on and remains in this mode until another program
is chosen. In smart mode it will aim for a relative humidity of 5055%,and the fan speed will be adjusted automatically.
HIGH: The unit will dehumidify and aim for the humidity set using
the up and down buttons.
LOW: The unit will dehumidify and aim for the humidity set using
the up and down buttons.
Air Purifier : The unit will run in fan mode and will not extract
water. Use with the HEPA or Active Carbon filter to improve air
quality or remove odour vic.
HUMIDITY
INDICATOR
LIGHT
HUMIDITY INDICATOR MODE
When the appliance is first started the indicator light will turn
on automatically. The colour of the indicator light will change
according to the humidity condition of the room it is situated in.
RED: High humidity, RH≥70%
ORANGE: Comfortable, 70%> RH ≥60%
GREEN: Dry, RH<60%
Press the “Humidity Indicator light” button to turn the light on/off.
NOTE: It can take around 2 minutes following a change in the
humidity for the indicator to change colour e.g. If the humidity
drops to 55% it may take 2 minutes before the indicator changes
to green.
UV
07
HUMIDITY LEVEL & TIMER 2 DIGIT DISPLAY
The led indicator performs the following functions:
1. When the unit is plugged in, it will indicate the humidity level of the room.
2. When the UP and DOWN buttons are pressed, it will indicate the desired humidity
currently set.
3. When the timer is programmed will show the duration.
Notes: When humidity level is outside the normal operational parameters will show LO/HI. If
ambient humidity is lower than 20%, it will show “LO” If ambient humidity is higher than 90%, it
will show “HI”
OSC
OSC. (Oscillation function)
There are three different options for the outer louvre on the unit. It can be set
at 45 or 90 degrees, or alternatively to swing. Use the dehumidier at a 45
degree angle or with swing for Laundry mode
UV
UV LIGHT (Air purier function)
To activate the UV function press the "UV" button and the indicator light
will illuminate. The Germicidal UV light will destroy germs, bacteria, fungi
improving the indoor air quality
HUMIDITY SETTING
Press the UP and DOWN buttons to select the desired relative humidity
level, the default relative humidity is 55%. When a relative humidity of 35%
is selected, the compressor will not stop until the water tank is full.
NOTE: The desired humidity cannot be changed in SMART mode.
TIMER
TIMER
Press the TIMER button to program the timer. When the timer is activated
the "TIMER" light will be illuminated. Before programming the timer, ensure
the timer function has not been activated (the light must be off). The
following timer programs are available.
DELAYED POWER-ON FUNCTION: With the appliance in stand-by, press
the TIMER button, then use the UP and DOWN buttons to set in how many
hours time you require the unit to start (1~24 hours).
DELAYED POWER-OFF FUNCTION: While the appliance is running with
the desired settings, press the TIMER button, then use the UP and DOWN
buttons to set in how many hours time you require the unit to stop (1~24
hours).
DEFROST
INTELLIGENT DEFROST
The appliance will defrost automatically when the coil sensor detects that
the internal temperature is too low. During defrosting the indicator will light
up. Once the defrost cycle has finished, the appliance will return to the
mode that was previously operating.
TANK FULL
TANK- FULL
When the water tank is full, the TANK FULL indicator light will flash, and
the unit will stop operating. One emptied and replaced, the appliance will
resume operation.
OPTIONAL CARBON FILTER (Air purication function)
Remove the carbon lter from the bag and insert it on the lter housing. It is
suggested to hoover the carbon lter every 2-3 weeks and change it every
3-6 months as this will help to ensure the room is kept fresh and odour free.
08
Power Button: Press to turn the dehumidier on and off.
Oscillation Button: Press once to make the louvre swing and press again to lock
at 45 degrees, press again to lock at 90 degrees. Do not operate the unit if the selfopening louvers do not open on power on.
Timer: Press the timer button, then use the buttons to adjust the
duration of the timer (1-24 hrs, start/ stop timer).
If set while the unit is running: The number will represent the number of hours the unit will
operate before turning off. This will not be affected if the unit enters defrost mode or the tank
is emptied and reinserted.
If set while the unit is in standby: the set number represents the period in hours after which
the unit will start. To cancel start / stop mode press the timer key again.
Up and Down Buttons: During the High or Low modes when the unit is
displaying the current relative humidity, these buttons can be used to adjust
the desired humidity level. The desired relative humidity can be set between
35 and 80% in 5% increments.
SMART Mode: This is designed for maximum convenience and
maintains the ideal domestic environment humidity level of 50-55%
while saving electricity. This is the default mode and is recommended for
most users.
During operation the compressor will operate until the desired humidity is reached and then
will stop. The economical low air purier mode will continue to operate. The fan moves the
air around the room ensuring the entire air in the room is processed and humidity correctly
measured.
To achieve drier air, or while drying laundry, put the unit in High mode and use the down
button to select a lower desired humidity (e.g. 35-45%).
LAUNDRY MODE: When drying clothes it is advised for the dehumidifier to operate
continuously with maximum water extraction until the water tank is full. Set the unit to the
High mode, and set the desired humidity level between 35%-50%. 35% is very dry and is
hardly achievable in a UK domestic environment. As such the unit will work until water tank
is full when set to 35%. Set the louvres to swing mode or to 45 degrees directing the airow
onto the clothes. Do not place clothes directly over any of the vents on the dehumidifier.
Make sure that there is nothing blocking the hot air exhaust air ow and for best results place
the laundry within 1.5 meters of the dehumidier.
NOTES:
POWER
OSC
TIMER
QUICK REFERENCE GUIDE
Air Purifier
If a permanent drainage pipe is tted the unit will not stop operating. Setting the desired
humidity to around 35% is good for laundry mode, a quick drying boost, or in emergencies.
It is not recommended for long normal operation in a domestic or ofce environment.
To allow more moisture in the air, press the up button and set to a higher desired humidity
(e.g. 60-70%).
We recommend setting the Humidity to 50-55%. This is great for domestic operation and
dry storage
Setting the humidity to 60% is great for personal comfort and applications where 50% RH
is considered too dry
Setting the humidity to 70% is ideal for unoccupied properties or where an economical run
is needed without the need to reduce the humidity further.
•
•
•
•
•
09
TANK FULL LIGHT
When the water tank is full, removed or incorrectly inserted the unit will stop dehumidifying,
the red tank full light will illuminate and the unit will beep. Empty the tank and reinsert it
correctly to resume operation.
AUTO DEFROST
When frost builds up on the evaporator coils, the compressor will cycle off and the unit will
go in to defrost mode. Following completion of the defrost mode, the unit will return to the
previously operating settings.
AUTO-RESTART (on some models)
If the unit stops unexpectedly due to the power cut, it will restart with the previous function
selected automatically when the power resumes, and the 3 minute compressor protection
has elapsed.
POWER
After the unit has stopped, to protect the compressor it is not recommended to resume
operation for at least 10 minutes. Operation can resume after this period lapses. When the
unit is restarted there is a 3 minutes delay before compressor will start.
LIGHTWEIGHT PORTABLE DESIGN ON CASTORS
The dehumidier is built to be compact and lightweight. The castors on the bottom of the unit
make it easy to move from room to room.
Your dehumidier contains an advanced micro-CPU controlled device which is capable of
self-diagnostics. The LCD display may also show the error and protections codes.
HUMIDISTAT CONTROL AND FAN/COMPRESSOR OPERATION
OTHER FEATURES AND INDICATORS
When the unit is running in a room with a temperature between 5oC and 12oC, it will enter
defrost mode roughly every 30 minutes.
When the unit is running in a room with a temperature between 12oC and 20oC, it will enter
the defrost mode roughly every 45 minutes.
When the humidity of the room is 2% lower than the desired humidity the compressor will
turn off automatically but the fan will continue to operate to ensure that the air within the
room is not stale. The unit will use only a minimal amount of energy in fan mode.
When the humidity of the room is equal to or higher than the desired humidity the
compressor will restart after a 3 minutes delay to protect the compressor.
•
•
•
•
10
A badly positioned dehumidifier will have little effect. In positioning the dehumidifier
please ensure circulation of air in not restricted around the unit.
Allow at least 20 cm space around the unit.
This dehumidifier is designed only for indoor
residential or small ofce applications and any
commercial or industrial use will invalidate the
warranty.
Use in an enclosed area for maximum
efficiency. Close all doors, windows to create
an effective operating environment. Do not use
outdoors.
Your electriQ dehumidifier will begin to
protect your space from the harmful effects of
excessive moisture as soon as it is turned on. Excess moisture is dispersed throughout
your home. For this reason, the dehumidier should be positioned in a central and clear
location so that it can draw this moist air towards it from all over the home. A warm
hallway or landing is an excellent position for your dehumidier. If possible, leave interior
doors ajar to allow air circulation.
Alternatively, if you have a serious problem in one area you can begin by positioning the
dehumidier there and moving it to a more central location at a later date. For the most
effective use, run your dehumidier with external doors and windows kept closed. Please
note the unit should not be placed directly against a radiator or other heat source.
When positioning your electriQ dehumidier, ensure that it is placed clear of any obstacle
that may limit the air movement. Place the dehumidier on a at dry surface.
Note: Do not force castors to move over carpet or uneven surfaces, nor move the unit
with water in the tank as it may tip over and spill water.
20cm
20cm
POSITIONING THE DEHUMIDIFIER
11
When the water tank is full, the unit will stop automatically. When this happens the TANK
FULL red light will show on the control panel, and the unit will bleep.
NOTE: Only empty the water tank when it is full or before moving or storing the unit.
There are two ways to dispense collected water.
1. USE THE TANK
When the tank is full, the unit will automatically stop running,
and the Tank Full indicator will ash.
Slowly pull out the tank. Grip the tank by its handle securely,
and carefully pull it out. Empty the water tank and reinsert it
into the dehumidier. The tank must be in place and securely
seated for the dehumidier to operate again. The dehumidier
will re-start when the tank is restored in its correct position.
NOTES:
When you remove the water tank, do not touch sensors or any parts which are situated
behind tank. Doing so may damage the product. Be sure to push the tank gently all the
way into the unit. Banging the bucket against anything or failing to push it in securely into
place may cause the unit not to operate.
Do not remove any parts from the water tank or tank enclosure. The water full sensor will
no longer be able to detect the water level correctly and water may leak from the water
tank.
2. CONTINUOUS DRAINAGE
Water can be automatically plumbed in or drained into a sink, a larger recipient or
through the wall into an outside drain by attaching a pipe to the unit (10 mm internal
diameter) (not included). Insert the pipe into the drain outlet at the back of the unit as
shown here.
Make sure the connection between pipe and the drain outlet is tight and does not leak.
Then direct the pipe to a suitable drainage point. This unit uses gravity to dispose of
water hence the drain should be lower than the water outlet on the unit. Put the tank
back. Be sure to run the water pipe downward and let the water to ow out smoothly. Do
not kink or bend the pipe.
The permanent drain can be used in conjunction with a water pump (e.g. when draining
from a cellar) to lift the water upwards.
OTHER FEATURES AND INDICATORS
12
Always shut off the unit and unplug from the mains before cleaning or performing any
maintenance. When it is not in use for long periods it is advisable to remove the plug
from the power socket. Do not use chemical solvents (such as benzene, alcohol or
gasoline) as they may cause irreversible damage to the unit.
1. CLEAN THE GRILLE AND CASE
Use water and a mild detergent to clean
the washable mesh lters. Do not use
bleach or abrasives. Do not splash
water directly onto the main unit. Doing
so may cause an electrical shock and
can lead to the insulation to deteriorate,
or cause the unit to rust. The air intake
and outlet grilles get soiled easily, so
use a vacuum attachment or soft brush
to clean. Wipe the dehumidifier body
with a soft damp cloth or kitchen towel.
Remove the ABS lter frame. If the optional carbon lters are tted, remove them from the
frame and hoover gently approcimately every 2-3 weeks.
If the mesh lter is dirty hoover it, if it is heavily soiled wash it with warm soapy water and dry
thoroughly before reinserting it in the unit.
When lter cleaning is nished and lters are dry placed them back into the unit.
NOTE: While the carbon filter is optional never run the unit without the mesh filter frame
correctly inserted.
2. CLEAN THE WATER TANK
Every few weeks, clean the tank to prevent growth of mould, mildew and bacteria. Partially ll
the tank with clean water and add a little mild detergent. Swish it around and than empty the
tank and rinse.
NOTE: Do not use a dishwasher to clean the tank. After cleaning and drying, the tank must
be reinserted securely into dehumidier in order to restart operation.
END OF SEASON MAINTENANCE
1. Empty and clean the water tank.
2. Clean the unit and the lters as per cleaning procedure above.
3. Coil the power cord on the special cord storage rest at the back of the unit
4. Cover the unit and keep it in a dry place.
CARE AND MAINTENANCE
13
FREQUENTLY ASKED QUESTIONS
Why doesn't the dehumidier seem to extract much water if the temperature is low?
This is a compressor dehumidifier which works best in temperatures above 15oC. If the
temperature is low and the air is dryer than the setting on the humidistat the unit will not
extract water. If you want to use a dehumidier for outside buildings, unheated properties,
boats or garages please check our desiccant range.
Why doesn't the unit work /or stops suddenly?
The water tank may be full or displaced. To rectify: empty the tank and carefully place the
tank back in the unit. Also the unit may be running in dehumidifying mode with a low room
temperature. Please check if the room temperature is lower than 5oC. If so, the unit will stop
working while in dehumidifying mode. (unit may be defrosting).
The ambient operating range is between 5oC and 35oC with a relative humidity ranging from
30% to 80%. For maximum efciency use the unit between 15oC and 32oC.
Sometimes cold and/or hot air comes out from the air outlet grill, why?
When the unit is in dehumidifying mode it absorbs humid air from room and freezes it to
reduce the humidity.
During the cold cycle there should be cold air coming out of the unit
During the hot cycle hot dry air should be coming out of the outlet grill.
TROUBLESHOOTING
：
Issue Cause Solution
Hot or cold air
being produced
Normal Operation When the unit is in dehumidifying mode it absorbs humid air from room and
freezes it to reduce the humidity.
During the cold cycle there should be cold air coming out of the unit
During the defrost cycle hot dry air should be coming out of the outlet grill.
Unit does not
operate
Is the plug properly
inserted in the socket?
Insert the plug into the socket and turn the switch on.
Does the tank full
indicator is red?
Tank full, oat displaced or tank not properly inserted. Empty tank, check oat
and make sure tank is properly inserted in unit.
Front louvres do
not open
Louvre motor is blocked Check if anything is blocking the louvre
Try to move gently the louvres up and down while the unit if off
If the above fails return the unit to service centre
Dehumidier
does not
extract water
Is the unit set to a
humidity level lower
than the one in the
room?
Set the humidity level on the humidistat bellow current humidity reading.
Is the temperature too
low for water extraction
to be efcient?
Increase temperature in the room or reposition the unit.
Is any intake grill or
discharge blocked? Is
the unit too close to
walls.
Remove obstructions and restart the unit.
Ensure a distance of at least 20 [cm between the unit & walls
Airow seems
weak
Is lter dirty or clogged? Please service the lters regularly as per user manual.
Unit is noisy
during operation
Is the unit on an
uneven surface?
Please place on at horizontal surface.
Is lter clogged? Please service the lters regularly as per user manual.
E3 or E4 Humidity sensor error Use the unit within the prescribed humidity range. Unplug the unit, rest and plug
it back in. If error repeats, call for service centre.
E1 or E2 Temperature sensor
error
Use the unit within the prescribed temperature range. Unplug the unit, rest and
plug it back in. If error repeats, call for service centre.
E5 or E6 Abnormal Coil sensor
temperature or current
Use the unit within the prescribed humidity and temperature range. Unplug the
unit, rest and plug it back in. If error repeats, call for service centre.
Defrost light on
and unit
stops regularly
Unit is defrosting Allow the unit to automatically defrost. The protection will clear after the unit self
defrosts. Increase temperature in the room if this repeats too often
Tank full red
light
Water tank full
notication
Tank is full or is not in the right position-- Empty the tank and replace in the right
position.
Any other malfunctions will need to be reported to electriQ service centre. Do not attempt unauthorised repairs as these may
invalidate the warranty.
14
Technical data
Model CD12LE-V3 CD20LE-V3
Voltage 1Ph, 220-240V~ 50Hz 1Ph, 220-240V~ 50Hz
Dehumidifying capacity
12 L / day
(at 30oC / 80%RH)
20 L / day
(at 30oC / 80%RH)
Fan Speeds 2 2
Power Consumption 180W 270W
Running Amps 0.91 Amps 1.2 Amps
Tank Capacity 4 litres 4 litres
Humidity settings range 35%~80% 35%~80%
IP RATING IPX1 IPX1
Refrigeran R290, 60 grams R290, 75 grams
Airow m3/h 180 180
High / Low Pressure 1.5/0.5MPa 1.5/0.5MPa
Max noise level dB(A) 42-49 42-49
Filters carbon (optional) carbon (optional)
Dimensions mm
(WxDxH)
380x580x195 380x580x195
Weight kgs 14.3 14.3
GWP 3 3
All information provided is for reference only. Products specications may change due to continuous
product development.
Disposal: Do not dispose this product as unsorted waste. Collection of such waste
must be handled separately as special treatment is necessary.
Recycling facilities are now available for all customers at which you can
deposit your old electrical products. Customers will be able to take any
old electrical equipment to participating sites run by their local councils.
Please remember that this equipment will be further handled during
the recycling process, so please be considerate when depositing your
equipment. Please contact the local council for details of your local
household waste recycling centres.
15
electriQ UK SUPPORT
www.electriQ.co.uk/support
Please, for your own convenience, make these simple checks before calling the
service line.
1. Has the unit been standing upright for at least 2 hours?
2. Is the unit plugged into the mains?
3. Is the fuse OK?
4. Switch the unit off and wait three minutes to see if the issue is resolved. Restart the unit.
5. Check if the water tank is full.
6. Was the troubleshooting guide followed?
If the unit still fails to operate call: 0871 620 1057 or complete the online form
Ofce hours: 9AM - 5PM Monday to Friday
Unit J6, Lowelds Business Park,
Lowelds Way, Elland
West Yorkshire, HX5 9DA
Loading...