Electra TG50W, TG60W, TG50B, TG60B Operating Manual

Download

Page 1

Operating

Manual

Operating Manual

FREESTANDING PRODUCTS DOUBLE OVEN

Service Helpline: 0333 577 7238

TG50W TG50B TG60W TG60B

Page 2

PART-1: SAFETY WARNINGS .................................................................4

PART-2: INSTALLATION AND PREPARATIONS FOR USE .................12

2.1 Ventilation requirements .................................................... 12

2.2 Installation of product ......................................................... 14

2.3 Gas connection .................................................................. 15

2.5 Electric connection and safety (If available) ...................... 26

2.6 Adjustment of feet .............................................................. 27

PART-3: CLEANING AND MAINTENANCE ...........................................28

3.1 Cleaning ............................................................................. 28

3.2 Maintenance ...................................................................... 33

PART-4: SERVICE AND TRANSPORT ..................................................34

4.1 Basic troubleshooting before contacting service .............. 34

4.2 Information related to transport .......................................... 35

CONTENTS

Page 3

Dear Customer,

Our goal is to offer you high quality products that exceed your expectations. Your appliance is produced in modern facilities and is carefully and particularly tested for quality.

This manual is prepared to help you use your appliance, which has been manufactured using the most recent technology, with

condence and maximum efciency.

Before using your appliance, carefully read this guide which includes basic information on safe installation, maintenance and use. Please contact your nearest Authorized Service centre for the installation of your product.

CE Declaration of conformity

This appliance has been designed to be used only for home cooking. Any other use

(such as heating a room) is improper and dangerous.

This appliance has been designed, constructed and marketed in compliance with:

-Gas appliances directive, 2009/142/EC

-Low voltage directive, 2006/95/EC

-EMC directive, 2004/108/EC

-CE marking directive, 93/68/EEC

* Visuals used in this user manual are schematic and may vary depending on model.

Page 4

PART-1: SAFETY WARNINGS

Read these instructions carefully and completely before using your appliance and keep it in a convenient place for reference when necessary.

This manual is prepared for more than one model in common. Your appliance may not have some of the features that are explained in this manual. Pay attention to the expressions

that have gures, while you are reading the operating manual.

General Safety Warnings

1. This appliance can be used by children aged from 8 years

and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge, if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children should not play with the appliance. Cleaning and user maintenance should not be made by children without supervision.

2. WARNING: The appliance and its accessible parts become hot during use. Care should be taken to avoid touching heating elements. Children less than 8 years of age should be kept away unless continuously supervised.

3. WARNING: Unattended cooking on a hob with fat or

oil can be dangerous and may result in re. NEVER try to extinguish a re with water, but switch off the appliance and then cover ame e.g. with a lid or a re blanket.

Page 5

4. WARNING: Danger of re: do not store items on the cooking

surfaces.

5. WARNING: If the surface is cracked, switch off the appliance to avoid the possibility of electric shock.

6. For hobs incorporating a lid, any spillage should be removed from the lid before opening. The hob surface should be allowed to cool before closing the lid.

7. The appliance is not intended to be operated by means of an external timer or separate remote-control system.

8. WARNING: In order to prevent tipping of the appliance, the stabilizing brackets must be installed. (For detail information please read the anti-tilting kit set guide.)

9. During use, the appliance becomes hot. Care should be taken to avoid touching heating elements inside the oven.

10. During use, handles held for short periods in normal use can get hot.

11. Do not use harsh abrasive cleaners or sharp metal scrapers to clean the oven door glass and other surface as they can scratch the surface, which may result in shattering of the glass or damage to the surface.

12. Do not use steam cleaners for cleaning the appliance.

Page 6

13. WARNING: Ensure that the appliance is switched off

before replacing the lamp to avoid the possibility of electric shock.

14. CAUTION: Accessible parts may be hot when the cooker or grill is in use. Young children should be kept away.

15. Your appliance is produced in accordance with all applicable local and international standards and regulations.

16. Maintenance and repair work must be made only by authorized service technicians. Installation and repair work carried out by unauthorized technicians may endanger you.

It is dangerous to alter or modify the specications of the

appliance in any way.

17. Prior to installation, ensure that the local distribution conditions (nature of the gas and gas pressure or electricity voltage and frequency) and the requirements of the appliance are compatible. The requirements for this appliance are stated on the relevant label.

18. CAUTION: This appliance is designed only for cooking food and is intended for indoor domestic household use only and should not be used for any other purpose or in any other application, such as for non-domestic use or in a commercial environment or room heating.

19. Do not try to lift or move the appliance by using door handle.

Page 7

20. This appliance is not connected to a combustion products

evacuation device. It should be installed and connected in accordance with current installation regulations. Particular attention should be given to the relevant requirements regarding ventilation.

21. If after 15 seconds the burner has not lit, stop operating the device, open the compartment door and wait at least 1 minute before attempting a further ignition of the burner.

22. These instructions are only valid if your country symbol appears on the appliance. If the symbol does not appear on the appliance, it is necessary to refer to the technical instructions which will provide the necessary instructions

concerning modication of the appliance to the conditions

of use of the country.

23. All possible security measures have been taken to ensure your safety. Since the glass may break, care should be taken while cleaning to avoid scratching. Avoid hitting or knocking the glass with accessories.

24. Ensure that the supply cord is not wedged during the installation. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly

qualied persons in order to prevent a hazard.

25. While the oven door is open,do not let children climb on the door or sit on it.

Page 8

Installation Warnings

26. Do not operate the appliance before it is fully installed.

27. The appliance must be installed by an authorized technician

and put into use. The producer is not responsible for any damage that might be caused by defective placement and installation by unauthorized people.

28. When the appliance is unpacked, make sure that it has not been damaged during transportation. In case of any

defect; do not use the appliance and contact a qualied

service agent immediately. As the materials used for packaging (nylon, staples, styrofoam...etc) may cause harmful effects to children, they should be collected and removed immediately.

29. Protect your appliance against atmospheric effects. Do not expose it to effects such as sun, rain, snow, excessive humidity etc.

30. The surrounding materials of the appliance (cabinet) must be able to withstand a temperature of min 100°C.

During usage

31. When the product is operated for the rst time, a certain

smell will emanate from the insulation materials and the

heater elements. Before using the cooker for the rst

time, operate it empty at the maximum temperature for 45 minutes. At the same time, the environment in which the product is installed, should be well ventilated.

Page 9

32. While opening the oven door during or after operation, step

back to avoid the hot steam coming out of the oven. There may be a risk of burns.

33. Do not put ammable or combustible materials, in or near

the appliance when it is operating.

34. Always use oven gloves to remove and replace food in the oven.

35. Do not leave the cooker while cooking with solid or liquid

oils. They may catch re under extreme heating conditions. Never pour water on to ames that are caused by oil. Cover the saucepan or frypan with its cover to choke the ame

and turn the cooker off.

36. Always position pans over the centre of the cooking zone, and turn the handles to a safe position so they cannot be knocked or grabbed.

37. If the product will not be used for a long period of time, turn the main control switch off. Also when not using a gas appliance, turn the gas valve off.

38. Make sure the appliance control knobs are always in the “0” (stop) position when not in use.

39. The trays incline when pulled out. Be careful not to let hot liquid spill over.

40. CAUTION: The use of a gas cooking appliance results in the production of heat, moisture and products of

Page 10

combustion in the room in which it is installed. Ensure that the kitchen is well ventilated especially when the appliance is in use. Keep natural ventilation holes open or install a mechanical ventilation device (mechanical extractor hood).

41. Prolonged intensive use of the appliance may call for additional ventilation, for example opening of a window or more effective ventilation, for example increasing the level of mechanical ventilation where present.

42. While using the grill burner, keep the oven door open and

always use the grill deector shield supplied with the

product. Never use the grill burner with the oven door closed.

43. CAUTION: Glass hob lids may shatter when heated. Turn off all the burners before shutting the lid. The hob surface should be allowed to cool before closing the lid.

44. When the door or drawer of the oven is open, do not leave anything on it. You may unbalance your appliance or break the cover.

45. Do not put heavy items, ammable or ignitable goods

(nylon, plastic bag, paper, cloth...etc) into the drawer. This includes cookware with plastic accessories (e.g. handles).

46. Do not hang towels, dishcloths or clothes from the appliance or its handles.

Page 11

During cleaning and maintenance

47. Always unplug the appliance before operations such as

cleaning or maintenance.

48. Do not remove the control knobs to clean the control panel.

49. To maintain the efciency and safety of your appliance, we

recommend you always use original spare parts and only our authorized service agents in case of need.

Warning Serious injury or death risk

Risk of electric shock Dangerous voltage risk

Caution Injury or property damage risk

Important Operating the system correctly

Notice Additional notes marked

Page 12

PART-2: INSTALLATION AND PREPARATIONS

FOR USE

This modern, functional and practical cooker, that has been manufactured with parts and materials of the highest quality, will meet your cooking needs in every aspect. You should read this manual to avoid a problem and to achive satisfactory results. The following information details correct installation and service processes. It must be read especially by the technician who will install the appliance.

Important: This appliance must be installed by a qualied

person according to the manufacturers installation instructions, local building regulations, gas authority codes and electrical wiring instructions.

2.1 Ventilation requirements

For rooms with a volume of less than 5 m3 - permanent ventilation of 100 cm2 free area is required.

For rooms with a volume of between 5 m3 and 10 m3 a permanent ventilation of 50 cm2 free area will be required unless the room has a door which opens directly to outside air, in which case no permanent ventilation is required.

Air inlet section

minimum 100cm

Air inlet section

minimum 100cm

Page 13

For rooms with a volume greater than 10 m3 - no permanent ventilation is required.

Pay attention: Regardless of room size, all rooms containing the appliance must have direct access to the outside air via an openable window or equivalent.

Emptying of the Burned Gases from Environment

Cooking appliances that operate with gas, throw the burned gas wastes out directly to the outside or through the cooker hoods that are connected to the a chimney that opens directly to the outside. If it seems not possible to install a cooker hood, it is required to set an electric fan on the window or wall that has access to fresh air. This electric fan must have the capacity to change the air of the kitchen environment 4-5 times of its own volume of air per hour.

Cooker hood

ue

Electrical ventilator

Air inlet section

minimum

100cm

Air inlet section

minimum

100cm

Page 14

2.2 Installation of product

There are some factors to which attention must be paid while installing your product. Care should be taken. Pay attention to the following instructions in order to prevent any problems and/or dangerous situations that may occur later.

The appliance can be placed close to other furniture on condition that in the area where the oven is set up, the furniture’s height does not exceed the height of the cooker panel.

Pay attention not to place it near the refrigerator, ammable or inammable materials such as curtains, cloths, etc. that will

begin to burn quickly.

The furniture close to the product must be manufactured resistant to temperatures up to 100°C.

If the kitchen furniture is higher than the cooktop, it must be at least 10cm away from the cooker’s side.

Minimum

42 cm

Min. 65cm

(with hood)

Min. 70cm

(without hood)

COOKER HOOD

Minimum

42 cm

Page 15

It is advised that there is a 2cm blank space around the product for air circulation.

(The minimum distance between the pan support and any wall cupboards or cooker hoods with a fan over the product, are

shown in the above gure.) The cooker hood must be at minimum

65cm height from the pan support. If there is no cooker hood, this height must not be less than 70cm.

2.3 Gas connection

Assembly of gas supply and leakage check

The connection of the appliance should be performed in accordance with local and international standards and regulations applicable. First check what type of gas should be installed to the cooker. This information is given by a sticker on the back of

the cooker. You can nd the information related to appropriate

gas types and appropriate gas injectors on the technical data table. Check that the feeding gas pressure is compliant with

values on the technical data table, to get maximum efciency

and to ensure the least consumption. If the pressure of used gas is different to the values stated or not stable in your area, it may be necessary to assemble pressure regulator on the gas inlet. It is essential that you contact an authorized service agent to make these adjustments.

The points that must be checked during exible hose assembly

If the gas connection is made by a exible hose that is xed on the gas inlet of the appliance, it must be xed by a pipe collar.

Page 16

Connect your appliance with a short and durable hose that is as close as possible to the gas source.

The hose’s permitted maximum length is 1.5m. The hose that brings gas to the appliance must be changed once a year for your safety.

The hose must be kept clear from areas that may heat up to temperatures in excess of 900C. The hose must not be ruptured, bent or folded. It must be kept clear of sharp corners, moving objects and should not be defective. Before assembly, it must be checked for any production defect.

As gas is turned on, all connection parts and hoses must be

checked with soapy water or leakage uids. No bubble should

appear. If there are bubbles, check the connection joint and

redo the test. Do not use naked ame to check for gas leaks. All

metal components used for the gas connection must be clear of rust. Also check the expiry dates of components to be used.

The points that must be checked during xed gas connection

assembly

To assemble a xed gas connection (gas connection made by

threads, e.g. a nut), there are different methods used in different countries. The most common parts are already supplied with your appliance. Any other part can be supplied as a spare part.

During connections, always keep the nut on the gas manifold

xed, while rotating the counter-part. Use appropriately sized

spanners for a safe connection. For all surfaces between different

Page 17

components, always use the seals provided in the gas conversion kit. The seals used during connection should also be approved to be used in gas connections. Do not use plumbing seals for gas connections.

Remember that this appliance is ready to be connected to the gas supply in the country for which it has been produced. The main country of destination is marked on the rear cover of the appliance. If you need to use it in another country, any of the

connections in the gure below can be required. In such a case,

contact local authorities to learn the correct gas connection.

Gas Pipe

Seal

Hose Fitting

Adapter

Gas Hose with Collar

Mechanical Gas Hose

It is required that an authorized service agent makes the appropriate gas connections in compliance with safety standards.

ATTENTION! Do not use any match or lighter to check for gas leaks.

Changing the gas inlet

For some countries, the gas inlet type can be different for NG/LPG gases. In such a case, remove the current connection components and nuts (if any) and connect the new gas supply accordingly. In all conditions, all components used in gas connections should be approved by local and/or international authorities. In all gas

Page 18

connections, refer to the “Assembly of gas supply and leakage check” clause explained before.

Anti-Tilting Kit

Anti-Tilting Bracket (x1)

(Will be installed to the

wall)

Adaptor (x1)

(Installed on the product)

The document bag contains an anti-tilting kit. Anti-tilting bracket (1) should be removed from the kit and installed onto the wall with the following measures. The adaptor (2) that will provide connection of the anti-tilting bracket to the oven is preinstalled to the oven with 4 screws. The height can be adjusted by loosening the 4 screws of the adaptor. After installation of the anti-tinting bracket to the wall, push the product up to wall and check if the bracket is placed on the cut out on the adaptor.

Page 19

Page 20

Anti-Tilting Bracket Ground

Mounting Information

PRODUCT THE MODEL A B

60x60

50x60

85 cm product 57 53,7

90 cm product 53 48,2

50x50

85 cm product 57 39,4

90 cm product 53 33,9

The anti-tilting bracket is screwed on the ground in the shown dimensions. The

product is xed to the anti-tilting bracket

by its adjustable foot.

Page 21

2.4 Gas conversion

Caution: The following procedures must be undertaken by

authorized service people.

Your appliance is adjusted to be operated with LPG/NG gas. The gas burners can be adapted to different types of gas, by replacing the corresponding injectors and adjusting the minimum

ame length suitable to the gas in use. For this purpose, the

following steps should be performed;

Changing injectors

Hob Burners

Cut off the main gas supply and unplug from the electric mains.

Remove the burner caps and the adapters.

Unscrew the injectors. For this, use a 7mm spanner.

Replace the injector with the ones from the gas conversion kit, with corresponding diameters suitable to the type of gas that is going to be used, according to the information chart (which is also supplied in the gas conversion kit).

Page 22

Grill Injectors

The grill injector is assembled by a single screw that is placed on the tip of the burner. This screw is already visible. Remove the screw, pull the grill burner to yourself and you will see the injector revealed on the rear surface of the oven cavity.

Remove the injectors with a 7mm spanner and replace the injector with the ones from the spare set, with corresponding diameters suitable to the type of gas that is going to be used, according to the information chart (which is supplied in the gas conversion kit).

Spanner

Injector

Screw

Grill burner

Page 23

Oven Injector

The oven burner is xed in its cradle by a single clip that is placed

on the left-hand side of the burner. Pull the clip (Figure 6) further left, and with your other hand, lift the burner up holding from the thermocouple/spark plug holder. The injector is placed on the right side of the burner cradle. Repeat the same procedure for both Main and Top Oven (if present) burners.

Clip

Page 24

Adjusting the minimum ame position

The ame length in the minimum position is adjusted with a at screw located on the valve. For valves with a ame failure

device, the screw is located on the side of the valve spindle.

For valves without a ame failure device, the screw is located inside the valve spindle. For easier reduced ame adjustment,

it is advised to remove the control panel (and microswitch, if present) during adjustment.

To determine the minimum position, ignite the burners and leave them on in the minimum position. With the help of a small screwdriver fasten or loosen the bypass screw around

90 angular degrees. When the ame has a length of at least

4mm, the gas is well distributed. Make sure that the flame does not die out when passing from the maximum position to

the minimum position. Create an articial wind with your hand toward the ame to see if the ames are stable.

Valve with ame failure device

Bypass Screw

Valve without ame failure

device

Screw(inside the hole)

Page 25

For the oven burner, operate the oven burner at the minimum position for 5 minutes, then open and close the oven door 2-3

times to check the ame stability of the burner. You do not need to reduce the ame size for grill burners.

The position of the bypass screw must be loosened for conversion from LPG to NG. For conversion from NG to LPG, the same screw must be fastened. Make sure that the appliance is unpluged from the electric mains and the gas supply is open.

Changing the gas inlet

Thermostatic oven valve

Bypass Screw

Non-thermostatic oven valve

Bypass Screw

Page 26

2.5 Electric connection and safety (If available)

During the electric connection, follow the instructions stated in the user manual.

The earthing cable must be connected to the earth terminal.

You have to ensure the power cord with suitable insulation is connected to the power source during the connection. If there is no appropriate earthed electric outlet in accordance with regulations in the place where the appliance is to be installed, contact the authorized service centre. The earthed electric outlet must be close to the appliance.

Do not use an extension cord.

The power cord must not touch any hot surface of the product.

In the case of the power cord being damaged, contact the Authorized Service centre to have it changed.

Any wrong electric connection may damage your appliance, as well as endangering your safety, rendering your guarantee invalid.

The appliance is adjusted for 230V 50Hz electricity. If the mains electricity is different, contact the authorized service centre.

Page 27

The supply cord should be kept away from hot parts of the appliance. Otherwise, the cord may be damaged, causing a short circuit.

The manufacturer declares that it has no responsibility against any kind of damages and losses that are caused by improper connections that are performed by unauthorized people.

2.6 Adjustment of feet

Your product stands on 4 adjustable feet. When the product is placed where it is to be used, check if the product is balanced. If not, you can make the adjustment by turning the feet clockwise as required. It is possible to raise the appliance a maximum of 30mm by the feet. When the feet are adjusted appropriately, do not move the appliance by dragging. It should be lifted to reposition.

Page 28

3.1 Cleaning

Be sure that all control switches are off and your appliance has cooled before cleaning your oven. Switch off the appliance. Check whether cleaning materials are appropriate and recommended by the manufacturer before using on your oven. As they may damage the surfaces, do not use caustic creams, abrasive cleaning powders,

thick wire wool or hard tools. Should any liquids overow, clean

the overflown liquids immediately to avoid enameled parts becoming damaged.

Cleaning of oven

The inside of enameled ovens are best cleaned when the oven is warm. Wipe the oven with a soft cloth that has been soaked in soapy water after each use. Later re-wipe it with a wet cloth and dry. It may be required to use a liquid cleaning material from time to time to completely clean. Do not clean with dry/ powder cleaners or steam cleaners.

Catalytic cleaning (If available)

Catalytic cleaning involves a coating, which is applied to the oven cavity. The catalytic liners eliminates small grease residues during cooking at high temperatures. If grease residues remain after cooking, these can be eliminated by using the oven empty at 2500C for one hour. There are limitations to the level of the

PART-3: CLEANING AND MAINTENANCE

Page 29

clean as it is dependent on where the liners are placed. The base is enamel and the door window is glass, both of which still need to be cleaned using household cleaners.

Removal of wire shelf

Removal of catalytic panel

To remove the wire rack; Pull the wire rack as shown in the picture. After releasing it from clips(1),lift it up(2).

To remove the catalytic liner;

Remove screws on the each catalytic liners.

Cleaning of Glass lid (If available)

In order to be able to clean the glass lid, use a glass cleaner. Then rinse & dry it with a dry cloth.

Removal of top oven door

To remove the oven door;

1. Open the oven door(1).

2. Open the saddle bracket (with the

aid of a screwdriver, etc.) up to end position(2).

Page 30

3. Close the door until it almost

reaches the full closed position as

shown in 3rd gure and remove the

door by pulling it towards yourself.

Removal of inner glass for prole oven doors

Before cleaning the oven door glass, you must pull out the inner glass as shown;

Pull the glass towards direction 1 as shown and release from the holder clip. Pull out the glass towards direction 2.

After cleaning; place the glass back

into position (towards direction 3) and x the glass in place with

the holder clip (towards direction 4).

Triple glass oven doors

If the oven door is a triple glass oven door, the third glass also can be pulled out using the same procedure.

After cleaning; place the glass back into position, sliding the glass under

the clips in position ‘’A’’, and x into

place under the clips in position ‘’B’’.

Page 31

NOTE:To re-assemble the door follow the opposite rules

of removal.

Please pay attention that the recessed forms should be

positioned properly on the hinge counterparts as shown on

2nd gure.

Cleaning of Gas Cooker - Hob Part

1. Lift up the pan supports, caps and crowns of hob burners.

2. Wipe and clean the back panel with a soapy cloth.

3. Wash the caps and crowns of hob burners and rinse them.

Do not leave them wet, immediately dry them with paper cloth.

4. After cleaning, make sure that you re-assemble the parts

correctly.

5. Do not clean any part of the hob with wire wool. It causes

the surface to be scratched.

6. The pan support top surfaces may, in time be scratched

due to usage. In this case, these parts may rust which is not a production fault.

7. During cleaning of the hob plate, make sure that no water

ows inside the burner cups, as this may block the injectors.

Page 32

Burner Caps

Periodically, enameled pan supports, enameled covers and burner heads must be washed with soapy warm water rinsed and dried. After drying them thoroughly, replace them correctly.

Hob Surface

Enamelled Parts:

In order to keep them as new, it is necessary to clean them frequently with mild warm soapy water and then dry with a cloth. Do not wash them while hot and never use abrasive powders or abrasive cleaning materials. Do not allow vinegar, coffee, milk, salt, water, lemon, or tomato juice to remain in contact with enameled parts for long periods of time.

Stainless Steel

Stainless steel parts must be cleaned frequently with warm, soapy water and a soft sponge and then dried with a soft cloth. Do not use abrasive powders or abrasive cleaning materials. Do not allow vinegar, coffee, milk, salt, water, lemon or tomato juice to remain in contact with stainless steel parts long periods of time.

Page 33

3.2 Maintenance

Change of Oven Lamp (If available)

At rst unplug the product from the

electric supply and make sure that the product is cool. Remove the bulb after removing the glass lens. Fit the new bulb (resistant to 300°C) in place of the bulb that you removed

(230 V, 25 Watt, Type E14). Replace the glass lens. Your product will then be ready for use.The lamp

design is specic for use in household cooking appliances and

it is not suitable for household room illumination.

Other Controls

Periodically check the gas connection pipe. If even only a small abnormality is detected, inform the technical service centre to have it replaced. We recommend that gas connection parts should be changed once a year. If any abnormality is felt while operating the control knobs of cooker, contact to the authorized service.

Page 34

4.1 Basic troubleshooting before contacting service

If the oven does not operate:

a) The oven may be switched off

b) There may be a power cut

c) The fuse board may have tripped

If the oven does not heat :

The heat may not have been adjusted with the oven’s heater control switch.

If the interior lighting lamp does not light :

a) Check the Electricity supply to the appliance

b) Change the bulb using the 3.2 guide

Cooking (If lower-upper part does not cook equally):

Check the shelf locations, cooking period and heat values according to the manual.

The hob burners do not operate correctly :

Check the burner parts are correctly assembled (especially after cleaning).

The gas supply pressure may be too low/high. For appliances working with bottled LPG, the LPG cylinder may be depleted.

PART-4: SERVICE AND TRANSPORT

Page 35

If after checking as above, you still have any problem with your product, please call the Authorized Service centre.

4.2 Information related to transport

If you need to transport the product, use the original product packaging and carry it using its original case. Follow the transport signs on the packaging. Tape the upper parts, caps and crowns and pan supports to the cooking panels. Place some paper between the upper cover and cooking panel, cover the upper cover, then tape it to the side surfaces of oven. Tape cardboard or paper onto the interior glass of the oven to prevent the trays in your oven damaging the oven door during transport. Also tape the oven door to the side panels.

If you do not have the original packaging; prepare a carriage box so that the appliance, especially the external surfaces (glass and painted surfaces) of the oven, are protected against external threats.

Page 36

The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring

this product is disposed of correctly, you will help

prevent potential negative consequences for the

environment and human health, which could otherwise

be caused by inappropriate waste handling of this product. For more detailed information about recyling

of this product, please contact your local city ofce,

your household waste disposal service or the shop where you purchased the product.

52165685 07/15