Electra APE.2S1.x&x, APE.2S0.x&x, APE.2F0.x&x, APE.2F1.x&x Installation Instructions Manual

Download

Page 1

Staple here!

www.electra.ro

APE.2F1.x&x

APE.2F0.x&x

APE.2S1.x&x

APE.2S0.x&x

RFID secure keyless entry

Call

Communication: FULL-DUPLEX hands-free Audio monitoring

Gate opening Open lock alert

3 volume levels + turned off Choose ringtone

Auxiliary function:

e.g.: auto gate/garage door opening

Extensions:

+3 additional indoor terminals +3 additional outdoor panels +1 doorbell: main indoor terminal connection

Installation instructions

Resident building intercom 2 families

touch line evolution

Page 2

page 2/6

OUTDOOR INDOOR

DC/AC

Lock

ATE.Sxx

Main 1

ATE.Sxx

Main 2

ATE .Sx x

Additional

ATE .Sx x

Additional

(Optio nal)

(Optional)

230 V a.c.

APE.2S0

Doorbell

SAC.V1A.DIN

AUX

ACC

12 V / 1,3 Ah

1 OVERVIEW

1.1 Essential components of the installation

( surf ace ) (  us h )

- Optional -

to ease the wiring

Programming

TAG.ELT.PRG

35 × 62 × 7 mm

Access

TAG.ELT.000

35 × 62 × 7 mm

YEM.21x (DC)

140 × 125 × 42 m m

YEM.32x (AC)

140 × 125 × 42 m m

APE .2S1.x&x

260 × 110 × 35 mm

APE.2S0.x&x

200 × 110 × 35 m m

APE .2F1.x&x

285 × 135 × 55 mm

APE .2F0.x&x

225 × 135 × 55 mm

SAC.V1A.DIN

141 × 130 × 73 mm

ACB.41A .DIN

70 × 100 × 60 mm

ATE .Sxx

170 × 96 × 28 m m

Electromagnetic lock Outdoor panel Power supply Connection box Indoor terminal TAGs

(Red)

1.3 Technical features

Power tension for SAC.V1A.DIN power supply 180 ... 256 V / 50 Hz

Power tension internal to the installation

12,0

... 14,3 V d.c.

Power expenditure from the 230

a.c. network Max. 0,2 A a.c.

Access code memory

80 access codes for every outdoor panel

Extra outdoor panels

+max. 3 additional panels

Extra indoor terminals

+max. 3 additional terminals: audio A T E. S x x or audio A T B.S x x

Lock timer

5 seconds (cannot be modied)

Auxiliary command operates only on the main outdoor panel (address 1)

Operating temperature range

-30

... +45 °C for outdoor components

0 ... +40 °C for indoor components

Maximum relative humidity

90% at +20

°C

Outdoor panel protection class IP 34

1.4 Wiring

APE.2xx.x &x ⟶ SAC.V1A.DIN

UTP CAT5 (AWG 24) cable for distances of max. 30m.

For longer distances: an additional cable (C u 2 × 0,25 mm2) will be installed, doubling the power intake.

SAC.V1A.DIN ⟶ AC B.4 1A.DIN ⟶ ATE.35S.x&x

UTP CAT5 (AWG 25) cable for distances of max. 100 m .

For longer distances: an additional cable (C u 2 × 0,25 mm2) will be installed, doubling the power intake.

APE.2xx.x &x ⟶ Electromagnetic lock

Flexible, multistrand cable, [Cu] 0,5

mm2 for distances of max. 20m.

ATE.35S.x&x ⟶ Doorbell

0,25 mm2 Cable

Installation Instructions - edition: 17.09.2012

Bd. Chimiei 8 • 700291 Iași, ROM ÂNIA J22/1225/1991 • RO1962470

Tel. +40 232 2 14.370 Fax +4 0 232 232.830

clientfeedback@electra.ro ofce@electra.ro www.electra.ro

1.2 Block diagram

Page 3

page 3/6

2 MOUNTING THE COMPONENTS OF THE INSTALLATION

2.1 Outdoor panel

Name/Address Module

Print th e label u sing:

Print Label ELT

www.electra.ro

Sticker

Fasteni ng clips

Before beginning ...

The outdoor panel is

mounted at the entrance

to the property, on the

body that is closest to the

pedestrian access gate.

A. Flush mounting

Main cabl e Lock ca ble

Cable f astenin g

and guiding piece

Special s crew wi th wrenc h

-5 cm

≈17cm

cable length

Align the edges of the shell to the surface of the wall. No inset/offset!

B. Surface mounting

TORKS S crewB4,2 × 60 Screw

(4 pcs .)

Main cabl e Lock ca ble

Cable f astenin g and guiding piece

≈17cm

cable length

(from the wall)

2.2 Power supply + Connection box (similar)

A. DIN bar mounting B. Surface mounting

Fasteni ng clipDIN bar

A3,5 × 32 Screw

(2 pc s.)

B2,9 × 9,5 Screw

(4 pcs .)

Protection lid (2 pc s.)

2.3 Indoor terminal

Before beginning ...

The indoor terminal

is mounted at the

location and height

discussed with the owner

(140 cm recommended height).

A3,5 × 35( 32) Screw (4 pcs .)

Cable f astenin g and guidi ng

pieces

≈18 cm

cable length

(from the wall)

Page 4

page 4/6

3 ELECTRICAL CONNECTIONS

3.1 Installation connections

ACB.41A .DINSAC.V1A.DIN

APE.2Sx APE.2Fx

+14 V

GND C/D

(DA TA)

-Uv

GNV

Vin

+14 V

GND

C/D

(DA TA)

+Uv

GNV

Vin

+14 V

GND

C/D

AUX

BUT

LA/C

-ACC

+ACC

UTP CAT 5 (AWG 24)

ACC

12 V/1,3 Ah

ATE .Sxx

+14 V

GND

C/D

Dbl

+14 V

GND C/D

(DA TA)

+14 V

GND C/D

(DA TA)

+14 V

GND C/D

(DA TA)

ATE .Sxx ATB.Sxx

ATE .Sxx

+14 V

GND

C/D

+14 V

GND

C/D

Dbl

2 x 0,5 mm

Cable

3 x 0,75 mm

Cable

Electrical panel

Door

opening

button

Auxiliary

command

(Open collector)

BLUE BLUE

BLUEBLUE

BROWN BROWN

BROWNBROWN

ORANGE ORANGE

ORANGEORANGE

GREEN GREEN

GREENGREEN

(Optional)

Indoor terminal

Additional

Apartament 2

Indoor terminal

Main

Apartament 2

Power Supply Audio connection box

Outdo or panel

230 Va.c./50Hz

Accumulator

Hub position

may be

different, but

the connections

are correct.

GREEN

ORANGE

BROWN

BLUE

Doorbell button

Indoor terminal

Main

Apartament 1

Electro-

magnetic

Lock

3.2 Lock connections

Drive current (DC)

BUT LC LA/C

YEM.22x

Electromagnetic lock

Drive Current (DC)

3 x 0,5 mm

Cable

Outdo or panel

...

GND

...

BUT LC LA/C

YEM.21x

GND

BY +Y

Electromagnetic lock

Drive Current (DC)

4 x 0,5 mm

Cable

Outdo or panel

Alternative current (AC)

YEM.32x

BY Y2 Y1

BUT

LA/C

Tran sfo rmer

Electromagnetic lock

Altern ative curre nt (AC)

Outdo or panel

12 Va.c. 230 V

a.c.

2 x 0,5 mm

Cable

BUT

LA/C

Electromagnetic lock

Altern ative curre nt (AC)

Outdo or panel

12 Va.c. 230 V

a.c.

Tran sfo rmer

2 x 0,5 mm

Cable

Hub details

+14 V

(+14 V d. c.; 2A) gen eral fee d of the ins talla tion

(except for video communicat ion)

GND

0 V (mass) gen eral fee d of the ins talla tion

C/D

audio and d ata communic ation

+Uv

monito r display f eed (+14 V d.c.)

-Uv

0 V (mass)mon itor displ ay feed

GNV

0 V (mass) vid eo signal re ferenc e

Vin

(1 V vv) video sign al input (al so val id for V1, V2 , V3 and V4)

Vout

(1 V vv) video sign al outpu t

Ucam

(+12 V d.c.; 0,2 A) exte rnal vide o camera f eed

AUX

auxilia ry comm and outp ut (open co llect or)

Dbl

connection for a doorbell button

BUT

connec tion fo r opening t he lock

DC lock co mmand

LA/C

DC/AC lo ck common

AC lock co mmand

+ACC

accumu lator co nnect ion (+12V; max. 7 Ah)

-ACC

accumulator connection

phase ( 230 V a.c. / 50 Hz)

null

earthing

Hubs sp ecifi c to ELECTRA locks

connec tion fo r opening t he lock

feed fo r Electra DC l ock

feed fo r Electra AC lo ck

Recommendation:

Connection to the grounding system: locally or from the distance (cable 1 x 0,75 mm2).

Page 5

page 5/6

4 INSTALLATION SETUP

4.1 Verifying the accuracy of the connections and connecting the power supply

Check the correctness of the connections in the installation!

The +14 V, C/D and GND signals are the same for all components of the install ation.

Any short-circuit between them will affect all the indoor terminals, causing them not to function.

Connect the power supply to the 230 V a.c. network through a 10 A automated fuse!

Optionally, the accumulator is connected to the +ACC;-ACC hubs of the SAC.V1A.DIN power supply.

Pay attention to the connection to the correct polarit y of the outdoor accumulator!

Check the correct functioning of the power supply:

• The measured tension at the hubs of the power supply: +14 V⟷GND / 13,8 ÷ 14,3 V d.c.

• Power supply signaling, according to the following table:

Signaling Observations Network tension

Tension presence: +14

V, +Uv

S1 permanent Green S2 permanent Green

The installation is ready to function.

If the audio or video communication is not functioning, check the status of fuses Sig.1 and Sig.2 from the power supply.

230

V ± 10%

50 Hz

+14 V⟷GND 1 3,8 ÷ 14,3 V d.c.

+Uv⟷-Uv 13,5 ÷ 1 5,0 V d.c.

S1 alternating Red/Green

S2 permanent Green

The installation is functioning.

Charging accumulator.

S1 alternating Red/Green + acoustic signaling

S2 permanent Green

The installation is functioning.

Faulty or uncharged accumulator: replace the accumulator!

S1 permanent/ashing Red

S2 turned off

The installation is functioning only on audio communication, for a limited amount of time.

Check the power fuse from the network and fuse Sig. 3.

NO: 0

+14 V⟷GND 10,5 ÷ 13,8 V d.c.

+Uv⟷-Uv NO: 0 V

S1 ashing Green

S2 turned off

The installation is NOT functioning.

Shortcircuit in the installation on +14

V and/or +Uv.

Eliminate the shortcircuit and re-establish the connection!

230

V ± 10%

50 Hz

NO: 0 V

4.2 Programming the Tags

The Red Programming TAG contains the unique code of the installation company.

When an outdoor panel reads a Programming TAG for the rst time, it is personalized with the company’s unique code.

The code is permanently registered in the panel’s memory and can only be erased at the producer.

The personalized panel will not accept the Programming TAGs of other installation companies.

How to program the TAGs’ Access Codes in the memory of the outdoor panel:

The door on which the lock is mounted will remain closed the entire time it takes to program the TAGs! Entering the programming mode with the door open will erase all acces codes.

1. Use the Red Programming TAG! The panel enters the Programming Mode: [

BEEP BEEP

BEEEEEEP

]

The Programming mode closes automatically if the panel is idle for more than 10 seconds or imediately by using the Programming TAG once more.

2. You now have a maximum of 10 sec. for each Access TAG. You will hear the following sounds:

• [

BEEP BEEP

] when the Access Code has been succesfully memorized,

• [

BEEP

] when the TAG’s Access Code is already in the panel’s memory,

• [

BEEP

] when the panel has been idle for 10 seconds and is no longer in the Programming Mode.

To erase ALL the Access Codes from the panel’s memory:

This action cannot be undone! The panel will not recognize any Access TAG.

1. Enter the Programming Mode! (by using the Programming TAG)

2. Operate the lock’s button* for at least 6 seconds! Acoustic conrmation: [

BEEP BEEP

BEEP

]

If the lock does not have a button, you need to short-circuit between the BUT and LC hubs (of the outdoor panel) for at least 6 seconds.

4.3 Programming the address of the additional outdoor panel

Remember:

The default address of all oudoor panels is 1.

The installation must have one outdoor panel with the adress 1. This will be the main panel.

The outdoor panels must have unique addresses within the installation.

The installation does not work if 2 panel’s share the same address!

How to program the additional outdoor panel:

The door on which the lock is mounted will remain closed the entire time it takes to program the additional panel!

1. Use the Red Programming TAG on the additional panel! The panel enters the Programming Mode: [

BEEP BEEP

BEEEEEEP

]

The Programming mode closes automatically if the panel is idle for more than 10 seconds or imediately by using the Programming TAG once more.

2. Press any key! [

BEEP

] when the panel’s address increases by +1, [

BEEP BEEP

BEEP

] when the panel is bak to having address 1.

For the following 10 seconds, the additional panel is still in the Programming Mode and you may proceed to program its Access TAGs.

Page 6

page 6/6

4.4 Programming the indoor terminals

The installation does not work if 2 terminals share the same address!

All indoor terminals leave the producer with address 1.

The main indoor terminal will nOT be programmed.

Operatorul 1 is programming from the main outdoor panel (address 1).

Operator 1

Main outdoor panel

Steps

Operator 2

Indoor terminal

Step 0

All LEDs are off.

ENTERING

programming mode

Operator 1 will hear [

BEEEEEEEEP

] in the outdoor

panel. Afterwards proceed to Step 2.

Step 1

Press both keys at the same time and

hold until Operator 1 is done programming*.

* You will hear the rst [

BEEP

] by touching the two keys and

the second [

BEEP

] when the terminal has been programmed

Hold the keys pressed until you hear

the second

[

BEEP

]

ENTERING

programming mode

Step 2

Press the apartment’s key, as many times as it

is shown in the table below:

( for every key you press you hear: [

BEEP

] )

Operator 2 Main Additional 1 Additional 2 Additional 3

Apart. 1

×2

(twice)

×3

(three times)

×4

(four times)

Apart. 2

(once)

×2

(twice)

×3

(three times)

×4

(four times)

Red/ White LED

during programming mode

Keep hold ing the keys

pressed!

EXITING

programming mode

Step 3

The panel makes a [

BEEP

] for conrmation.

Step 3

You will hear the second [

BEEP

You can now release the keys!

EXITING

programming mode

You have succesfully programmed an indoor terminal.

Call to check!

We encourage you to program the additional indoor terminals at the head ofce. With the devices laid out on a table, one operator follows the same steps.

Label the devices you program so you don’t misplace them in the installation.

4.5 Functions and adjustments

1. Check anywhere within the installation, during the

call and the communication, that the power tension

between +14 V ⟷ GND is higher than 1 2,0 V.

2. Check the functions of the indoor terminals and the outdoor

panels: call, communication, access, audio monitoring. When calling from outside, all indoor terminals will ring, but

just the one you answer from can be used during the call.

The installation has been adjusted by the producer for audio

communication to suit standard functioning conditions.

How to adjust the volume of the indoor terminal:

When the LED is Red, the terminal is silent.

By pressing the key you change between

different volume levels ( White LED).

Af tertheverications,leavetheindoorterminalonOpenVolume:

→ white LED on.

How to choose the terminal’s ringtone:

1. Simultaneously press and hold keys:

2. Release the keys a few seconds after begins ashing Red/White!

3. Press to switch between ringtones.

4. Press to set the ringtone.