Elecom oppopet M-NE2DR Series User Manual
- 1 -
CAUTION
Do not place this product in any of the following environments:
In a car exposed to sunlight, a place exposed to direct sunlight, •
or a place that becomes hot (around a heater, etc.)
In a moist place or a place where condensation may occur•
In an uneven place or a place exposed to vibration•
In a place where a magnetic eld is generated (near a magnet, •
etc.)
In a dusty place•
This product doe s not have a waterp roof structu re. U se an d
store this product in a place where the product body will not be
splashed with water or other liquid.
Rain, water mist, juice, coffee, steam or sweat may also cause
product damage.
Do not use this product with any device that may signicantly
●
aect other equipment in the event that it malfunctions.
If this pro duct is us ed on a t ransp arent su rfac e s uch as
●
glass or a high ly reflec tive sur face su ch a s a mi rror, the
optical sen sor will not func tion correct ly and mouse curs or
movement will become unstable.
Whe n no t us in g th e mo us e fo r on e mo nth or m ore ,
●
disconnect the receiver unit from the PC.
When you n o lon ger n eed t o use thi s prod uct, be s ure t o
●
dispose of it in accordance with the local ordinances and laws
of your area.
Avoid looking directly at the light of the sensor as doing so
●
may cause eye damage.
Always keep the receiver unit out o f the reach of children as
●
there is a danger that they may swallow it.
Batteries
CAUTION
Use AAA alkaline batteri es, AAA manganese batterie s, or AAA
nickel hydride storage batteries with this product.
If this product will be unused for a long period of time, remove
the battery to avoid battery leakage and failure.
Cleaning the Mouse
If the product body becomes dirty, wipe it with a soft, dry cloth.
Use of a volatile liquid (paint thinner, benzene, alcohol, etc.) may affect
the material quality and colour of the product.
Cautions for Wireless Equipment
This product is wireless equipment using the entire range
of the 2.4 GHz band and it is possible to avoid the band of
mobile object identification systems. FH-SS is used for the radio wave method. The
interference distance is 10 m.
The 2.4 GHz band is also used by medical equipment, Bluetooth, and wireless LAN
equipment conforming to the IEEE802.11b/11g/11n standard.
Before using this product, check that there are no other “radio stations”* operating
•
nearby.
If electromagnetic interference occurs between this product and other “radio
•
stations”, move this product to another location or stop using this product.
* Other “radio stations” refer to industrial, scientific and medical devices using the 2.4
GHz band like this product, other radio stations of this type, licensed radio station
premises for mobile object identification system that is used in factory production
lines, certain non-licensed low power radio stations and amateur radio stations.
WARNING
Do not use this product with a device that may have a serious
●
function or inuence. There are rare cases w here an external
radio wave at the sam e frequency or the radio wave emitted
from a mobile phone causes this product to malfunction, slow
down, or fail to operate.
Do not use this product in a hospital or other locations where
●
the use of rad io waves is pr ohibi ted. The rad io waves of
this product may affect electronic and medical devices (e.g.
pacemaker).
The use of a wireless mouse in an aircraft is prohibited by
●
aviation law because doing so may interfere with ight safety.
Turn of f the power of the mouse body before boardin g an
aircraft and do not use it in the aircraft.
* ELECO M i s n ot liab le for any ac cide nt or soci al dama ges
incurred by the failure of this product.
2.4FH1
Safety Precautions
Meaning of symbols
WARNING
Failure to observe precautions may result in serious personal injury or death due to
re, electric shock, or other causes.
CAUTION
Failure to observe precautions may result in personal injury due to elec tric shock or
other causes, and may damage other equipment.
Prohibited action
Mandatory action
Situation that needs attention
Notes and reference information
Information that is handy to know
Observe these precautions carefully to avoid personal injury, damage, re, and other problems
WARNING
If a foreign object (water, metal chip, etc.) enters the product, immediately stop using the
product and disconnect the receiver unit from the PC, and remove the battery from the
mouse. If you continue to use the product under these conditions, it may cause a re or
electric shock.
If an abnormality is found with this product (emission of heat, smoke or abnormal smell
from the product ), immed iately s top using the product, shutdown the P C, and after
thoroughly checking that heat from the product will not cause burns, disconnect the
receiver unit from the PC, and remove the battery from the mouse. After doing this,
contact the retailer from whom you purchased the product.
Do not drop or hit this product.
If this product is damaged, immediately stop using the product and disconnect the
receiver unit from the PC, and remove the battery from the mouse.
If you continue to use the product under these conditions, it may cause a re or electric
shock.
Do not attempt to disassemble, modify or repair this product by yourself, as this may
cause a re, electric shock or product damage.
Do not put this product in re, as the product may burst, resulting in a re or injury.
Do not connect or disconnect the receiver unit with a wet hand, modify the receiver unit
or bend it forcibly, as this may cause a re or electric shock.
The receiver unit contains small parts that could be swallowed by a child. Ensure that the
unit is stored in an area where it is not accessible to children.
Package Contents
This product ’s packaging contains the items listed b elow. Before using
the product, check that all items are present. We make every effort to
ensure that all p roducts are packaged correctly. However, in the event
that an item is missing or damaged, contact the retailer from whom you
purchased the product.
Mouse x1
•
Receiver unit x1
•
AAA alkaline battery x1
•
User’s Manual x1
•
Part Names
Mouse
Receiver unit
Left button
Used for left-click operation.
Right button
Used for right-click operation.
Wheel
The wheel can be turned back and forward with your nger or pressed like
a button to operate the PC.
Receiver unit housing
Used to store the receiver unit.
Power switch
Used to turn the mouse body on and o.
Optical sensor
Illuminates red when the mouse body is turned on. When the mouse body
is moved, this sensor detects mouse movement.
Avoid looking directly at the light of the sensor as doing so may cause *
eye damage.
Battery cover
This cover is removed to install batteries.
Battery housing
Batteries are inserted here.
USB connector (Male)
Connected to a PC USB port.
Receiver unit cap
A removable silicon cap. You can adjust the orientation of the cap to
match the orientation of the PC’s USB port.
Vary the style depending on which colour you buy.
Removing the cap
When removing the cap from the receiver unit, hold both the cap and the
connector, and pull out in a straight manner.
When removing the receiver unit from the USB port, the cap may
come o. If this happens, remove the separated receiver unit by itself.
Installing·Replacing the Battery
Before using this product, install one AAA battery in the mouse body.
Remove the battery cover.
Insert the battery.
Make sure that the polarity is
●
correct.
Install the battery cover as before.
Replacing battery
Remove the battery cover.
Remove the battery.
Insert the battery.
Install the battery cover as before.
Turning On and O the Mouse
Turning on the mouse
When using this product, turn the mouse body power on.
Slide the power switch to the ON position
Turning off the mouse
When not using this product, turn the mouse body o to save
battery power.
Slide the power switch to the OFF position.
Restoring from sleep state
Click the right mouse button.
To reduce battery drain, the mouse enters sleep mode
automatically if i t is left wit hout bein g operate d for a certai n
period of time with the power or switch turned on.
Inserting and Taking Out the Receiver Unit
Inserting the receiver unit
Receiver unit stowed
Place the receiver unit into the
receiver unit housing.
Taking out the receiver unit
Take the receiver unit out of
the receiver unit housing.
Preparation before Use
S
tep
1
Check USB ports
Check the USB port on your computer.
USB port
Any USB port may be used.
●
This product can be connected to a USB hub. However, it may not
●
work depending on the power supply capability of the USB hub.
S
tep
2
Installing the Receiver Unit
Activate the PC.
If Windows® prompts you to choose an account (a user name) when
●
it starts up, be sure to log on using an administrator account.
Wait until Windows® has started up completely.
●
Insert the receiver unit into the USB port of the PC.
USB port
Receiver unit
Insert here.
Carefully check the orientation of the connector and the
●
place where you will connect the receiver unit.
If you feel strong resistance when inser ting the receiver
●
unit, check that the shape and orientation of the connector
is correct. Using excessive force may damage the connector
and cause injury.
When removing the receiver unit from the USB port, the
●
cap may come o. If this happens, remove the separated
receiver unit by itself.
The mouse driver is installed automatically.
S
tep
3
Checking operation
Check that the mouse scrolls up and down correctly in Windows®
Internet Explorer.
From the [Start] menu, select [All Programs], and then [Internet
Explorer].
Internet Explorer will launch.
Display your favourite web site in Internet Explorer and change
the size of the window so that the vertical scrollbar appears.
* The sample website used here is the ELECOM homepage
Scrollbar
Scroll the tilt wheel back and forth.
The mouse is operating normally if the screen
moves up and down as you scroll the tilt wheel.
In applications that do not support scrolling, the screen will
not move when you scroll the tilt wheel.
Disconnecting the receiver unit
This product is hot-pluggable. It is possible to disconnec t the receiver unit when
PC is running.
Operation may become unstable if the receiver unit is
disconnected and reconnected several times when PC is running.
If this occurs, restart PC.
When using Windows®
Thank you for purchasing the ELECOM M-NE2DR Series wireless optical mouse.
This manual describes the operating instructions and safety precautions for using the
M-NE2DR Series. Ensure that you have re ad thi s manu al befo re usin g the produc t. Aft er
reading this manual, store it somewhere safe for future reference.
* Except in certain cases, the M-NE2DR Series is referred to as “this product” in this manual.
Wireless Optical Mouse
M-NE2DR Series
User's Manual
- 2 -
Troubleshooting
When the product appears to be
malfunctioning
When the mouse pointer on the screen does not move,
or moves unstably, when the mouse is moved
It is possible th at the reectivity of the surface on which this
product is being used is not suitable for an optical mouse.
Use this product on a mouse pad that is designed for use with
optical mice.
When using this product on a metallic surfa ce such as a steel
desk, radio wave outreach may be shortened. In such cases,
move the receiver unit closer to the mouse until mouse
operation stabilises.
It is possible that the receiver unit is not connected correctly to
the USB port. Disconnect the receiver unit from the USB port and
reconnect it.
The receiver unit and the mouse body are too far apart or there
is a possibility that the receiver unit is facing in a direction from
which it cannot receive radio signals. Adjust the position of the
receiver unit.
The op erabl e r ange of thi s
product is the area within a
circle with a radius of 10 m
from the receiver unit.
Depending on the usage
environment, the mouse may
not operate even when it is
withi n ap proxim ately 10 m
of the receiver unit. In such
to the receiver unit until operation stabilises.
Interference may occur if multiple units of this product are used
together or if this product is used with other wireless devices.
In such case, move the mouse closer to the receiver unit until
operation stabilises.
(Multiple units of this product have an automatic channel
avoidance function.)
Operation becomes unstable when battery power is low. See
“Installing·Replacing the Battery” on the reverse of this sheet, and
replace the batteries as soon as possible.
The alkali ne b atteri es s upplie d wi th t his p roduc t are for
•
checking product operation. These batteries may discharge
and drain during storing and shipping.
* When not using the mouse, turn it o to save battery power.
It is possible that the standard Windows mouse driver did not
install correctly and that this product is detected as an unknown
device by Windows®. This product is usually detected as a USB
human interface device. If it is detected as an unknown device, see
“Removing an unknown device,” and after removing the device
from Device Manager, repeat “Step 2 - Installing the Receiver Unit ”
on the front of this sheet.
If you have installed drivers and settings utilities produced by the
original manufacturer for a previous mouse, uninstall them first.
This product may not operate correctly if a driver made by another
company is installed. See the instruction manual that was supplied
with your previous mouse for uninstall instructions.
It is possible th at the driver is conicting w ith another driver
such as th at for a lap top tou ch pad. To use thi s p rodu ct
correctly, you must delete the touch pad driver. However, if you
delete this driver, you may not be able to use the touch pad or
touch pad functions. Contact the PC manufacturer for more
details.
The wheel moves, but the mouse cursor does not
In certain applications that do not support the scrolling
function, the mouse cursor will not move when you move the
wheel.
Approximately
10 m
Receiver unit
Basic specications
Product name Wireless Optical Mouse
Article No. M-NE2DR Series
OS Windows 7 (up to SP1), Windows Vista (up to SP2),
Windows XP (SP2 to SP3)
Mac OS X (10.5 to 10.5.8, 10.6 to 10.6.7)
Resolution (dpi) 1000
Interface USB
Radio frequency 2.4 GHz bandwidth
Radio wave method FH-SS modulation
Radio wave outreach Non-magnetic substance (e.g. wooden desk): Approx.
10 m
Magnetic substance (e.g. metal desk): Approx. 3 m
* Test values in the ELECOM environment
Mouse body dimensions 60.0 ( W) x 87.8 (D) x 38.0 (H) mm
Receiver unit dimensions 15.6 (W) x 20.0 (D) x 6.5 (H) mm
(When the cap is removed)
Operating temperature/
humidity
5 to 40°C, 90% RH max. (no condensation)
Storing temperature/
humidity
-10 to 60°C, 90% RH max. (no condensation)
Batteries AAA alkaline battery, AAA manganese battery, AAA
nickel hydride storage battery
Operating time Measure of the operating time when an AAA alkaline
battery is used
Continuous operating time: Approx. 69 hours
Continuous standby time: Approx. 75 days
Estimated serviceable time: Approx. 31 days
(when the PC is operated for eight hours a day
and 25% of the PC operation is assigned to mouse
operation)
Removing an unknown device
If the standard Windows mouse driver did not install correctly and
this product is detected as an unk nown device, remove the unknown
device from Device Manager, and then repeat “Step 2 - Installing the
Receiver Unit” on the front of this sheet.
If there are multiple unknown devices, before
●
removing a device, check that it is actually this
product. Disconnect the receiver unit and check
which unknown device disappears. The device
that disappears is this product.
If the unknown device does not disappear
●
even after you have deleted the driver
following the instructions below, it is possible
that there is something wrong with the PC.
Contact the PC manufacturer.
With the receiver unit connected to the PC, follow the
procedure below to remove the unknown device.
* Be sure to log on using an administrator account when
Windows starts up.
* Screen d isplay ma y differ dependin g on operating
system, but the procedure remains the same.
Display Device Manager.
Windows® 7 and Windows Vista®
●
1. From the [Start] menu, right-click [Computer].
2. Click [Properties].
3. Click [Device Manager].
Windows® XP
●
1. From the [Start] menu, right-click [My Computer].
2. Click [Properties].
3. Click the [Hardware] tab.
4. Click
.
The Device Manager window appears. Right-click the
unknown device, and click [Uninstall].
Click .
Disconnect the receiver unit and
restart the PC.
Repeat the procedure from "Step 2 - Installing the Receiver
Unit" on the front of this sheet.
Wireless Optical Mouse
M-NE2DR Series
User's manual
1st edition, December 1, 2011
ELECOM Co., Ltd
This manual is copyright of ELECOM Co., Ltd.
•
Unauthorised copying and/or reproducing of all or part of this
•
manual is prohibited.
The specifications and appearance of this product may be changed
•
without prior notice for product improvement purposes.
ELECOM Co., Ltd. shall bear no responsibility for any and all affects
•
resulting from the use of this product regardless of the above
reasons.
Export or service transaction permission under the Foreign
•
Exchange and Foreign Trade Control Law is required in order to
export this product or parts of this product that constitute strategic
materials or services.
Windows and the Windows logo are trademarks of the Microsoft
•
group of companies.
Mac, Mac OS , a nd M acin tosh are re giste red trad emark s o r
•
trademarks of Apple Inc., in the United States
Compan y n ames, pr oduct na mes, and ot her name s i n t his
•
manual are generally trademarks or registered trademarks.
©
2011 ELECOM Co., Ltd. All Rights Reserved.
廢電池請回收
低功率電波輻射性電機管理辦法
第十二條
經型式認證合格之低功率射頻電機，非經 許可，公司、商號或使用者均不
得擅自變更頻率、加大功率或變更原設計之特性及功能。
第十四條
低功率射頻電機之使用不得影響飛航安全及干擾合法通信；
經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。
前項合法通信，指依電信規定作業之無線電通信。
低功率射頻電機須忍受合法通信或工業、科學 及醫療用電波輻射性電機設
備之干擾。
당해 무선설비는 운용 중 전파혼신 가능성이 있음 .
이 기기는 가정용 (B급 ) 전자파적합기기로서 주로 가정에서 사용하는
것을 목적으로 하며 , 모든 지역에서 사용할 수 있습니다.
S
tep
1
Check USB ports
Check the USB port on your computer.
USB port
Any USB port may be used.
●
This product can be connected to a USB hub. However, it
●
may not work depending on the power supply capability
of the USB hub.
S
tep
2
Installing the Receiver Unit
Activate the Macintosh.
Wait until Mac OS X has started up completely.
●
Insert the receiver unit into a USB port on your Macintosh.
USB port
Receiver unit
Insert here.
Carefully check the orientation of the connector and
●
the place where you will connect the receiver unit.
If you feel strong resistance when inserting the
●
receiver unit, check that the shape and orientation
of the connector is correct. Using excessive force
may damage the connector and cause injury.
When removing the receiver unit from the USB
●
port, the cap may come off. If this happens,
remove the separated receiver unit by itself.
The mouse driver is installed automatically.
S
tep
3
Checking operation
Check that the vertical scrolling func tions are working correctly
in Safari.
Click the Safari icon in the Dock.
Safari will launch.
If Safari is not in the Dock, doubleclick the Sa fari icon in the Applications
folder.
Display your favourite web site in Safari and change the
size of the window so that the vertical scrollbars appear.
* The sample website used here is the ELECOM homepage.
Scrollbar
Scroll the wheel back and forth.
The mouse is operating normally if the screen
moves up and down as you scroll the wheel.
In applications that do not support scrolling, the
screen will not move when you scroll the wheel.
Disconnecting the receiver unit
This product is hot-pluggable. It is possible to disconnect the receiver unit
when PC is running.
Operation may become unstable if the receiver unit is
disconnected and reconnected several times when PC is
running. If this occurs, restart PC.
When using Mac OS X
产品中有毒有害物质或元素的名称及含量
根据中国”电子信息产品污染控制管理办法”
M-NE2DR测试结果
分解部位区分
有毒有害物质或元素
铅
(Pb)镉（Cd）汞 （Hg）
六价铬
（Cr (VI)）
多溴联苯
（PBB）
多溴二苯醚
（PBDE）
① USB接口 ○ ○ ○ ○ ○ ○
② 鼠标 ○ ○ ○ ○ ○ ○
○： 表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T 11363-2006
标准规定的限量要求以下。
×： 表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T
11363-2006 标准规定的限量要求。
ELECOM CO., LTD.
1-1 Fushimi-machi 4-Chome Chuoku, Osaka Japan 541-8765
URL: http://www.elecom.co.jp/global/
overseas@elecom.co.jp
宜麗客（上海）貿易有限公司
上海市徐匯区肇嘉浜路 1065 甲号飛雕国際大厦704 号
電話 : 86-21-33680011
FAX : 86-21-64271706
URL : http://www.elecom-china.com/
ELECOM Korea Co., Ltd.
5F Suam Bldg. 1358-17, Seocho2-dong, Seocho-gu, Seoul
137-862, Korea
TEL : 1588-9514
FAX : (02)3472-5533
URL : www.elecom.co.kr
ELECOM Singapore Pte. Ltd
33 UBI AVENUE 3 # 03-56. VERTEX SINGAPORE (408868)
TEL : (65)-6347-7747
FAX : (65)-6753-1791
The device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
NOTE; This equipment has been tes ted and found to comply with the
limits for a Class B Digital Device, pursuant to part 15 of the FCC Rules.
These l imits a re desi gned to provid e reaso nable protection agains t
harmfu l i nterf erence in a resi dentia l i nstal lation . Th is e quipm ent
generates, uses and can radiated radio fre quency energy an d, if not
instal led and used in accord ance with the inst ructi on, may cause
harmful interfer ence to radio commun ication. However, there is no
grantee that interferen ce will not occu r in a particu lar instal lation. If
this equipment do es cause harm ful interference to radio or television
reception, which can be determined by tuning the equipment o and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit dierent from that
towhich the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Notice: Changes or modications not expressly approved by the par ty
responsible for compliance could void the user’s authority to operate
the equipment.
Any ch anges or modifi cations not expr essly approv ed by ELE COM
responsible for compliance could void the user's authority to operate
the equipment.
WARNING: T his p roduct contai ns a chemic al kn own t o the State of
California to cause cancer, birth defects or other reproductive harm.
EMB21-M11
Loading...