Eleaf iJust D16 Kit User Manual

Notice for Use

Thanks for choosing Eleaf product! Please read this manual carefully before use so that
you can use it correctly. If you require more information or have questions about the
product or its use, please consult your local agents, or visit our website at
www.eleafworld.com.

Product Introduction

iJust D16 Kit features the adjustable voltage from 3.3V to 5V and the maximum
output 10 watts which can offer you a strong vaping experience. A variety of
advanced features we can find: elegant appearance with smooth touch;850mAh/
1700mAh battery capacity, tail LED digital screen which can show you current
voltage, total puffs, vaping seconds. Now, just begin to enjoy your modern and
digital vaping life with iJust D16 Kit.

How to use

Power on and off:Press the button for 5 times in quick succession, the button light will

flash 5 times to indicate iJust D16 is ready for use. The tail LED digital screen will show
the current power. In the same way,iJust D16 will be powered off after 5 presses.

Vape: Long press the button while inhaling the mouthpiece lightly to get a puff. The tail
LED digital screen will show the increasing vaping seconds. When you loosen the button,
the total vaping seconds will be displayed for 0.5 seconds. After that, the tail LED digital
screen will show the current power for 3 seconds.

VV mode (3.3V-5V): In this mode, voltage output can be adjusted by rotating the
regulation ring clockwise or counterclockwise. The tail LED digital screen will show the
current voltage during adjusting.

Charging: Plug the USB cable to the iJust D16, and connect it to the wall adaptor or
other power source such as a computer. (it can be used whilst on charge)
(During charging,the “%”symbol on the bottom of battery will keep flashing and stop
flashing when fully charged)

E-liquid filling ：

Unscrew GS16 atomizer base out of atomizer. Refill e-liquid into the atomizer through the
small holes.Screw atomizer base onto atomizer.(NOTE: Please do not overfill. Leave a
small air pocket in order to avoid leakage.)

iJust D16 Kit

User Manual

iJust D16 GS16 Tube Mouthpiece

BDC atomizer head Replacement:

Screw the base off connector firstly. Pull out the BDC atomizer head from the base and
replace a new one.

Properties

Over-current Protection: When over-current protection occurs, the vaping seconds

on the LED digital screen will stop increasing. Two seconds later, the LED digital screen
will show the current voltage for five seconds. At the same time, the button light will flash
five times.

Short-circuit Protection: When short-circuit occurs, the battery will shut off
automatically.

Low-voltage Protection: When the voltage of battery is below 3.3V, the button light
will flash 40 times. At the same time, the LED digital screen will go out.
Unlock the Low-voltage Protection:When the voltage of battery is above 3.65V, the
low-voltage protection will be unlocked.

Warranty

Please consult your Eleaf product warranty card. We are not responsible for any
damages caused by human error. Our warranty is not available for products purchased
from third-party vendors.

Precautions

a) Only have your iJust D16 Kit repaired by Eleaf. Do not attempt to repair the unit by

yourself as damage or personal injury may occur.

b) Do not leave the iJust D16 Kit in high temperatures or damp conditions, otherwise it

may be damaged. The appropriate operation temperature is within 0℃to45℃ while
charging and -10℃ to 60℃ while using.

c) Do not attempt to combine the iJust D16 Kit with parts from other brands of

e-cigarettes. If it is damaged in this way, our company will not take on responsibility
and your warranty will be void.

Base BDC Atomizer Head Atomizer Tube Mouthpiece

Email:[e-mail]

Web:www.eleafworld.com