eldoLED POWERdrive 6060/R Design-in Manual

© 2015 eldoLED. All rights reserved. V1.2 All content contained herein is subject to change without prior notice.

More product documentation and eldoLED´s terms and conditions are available at www.eldoLED.com

Design-in guide

POWERdrive 6060/R

2

Table of Contents

1. Technical characteristics 4

1.1 Input characteristics 4

1.2 Output characteristics 5

1.3 Control characteristics 5

1.4 Protection 5

1.5 Thermal characteristics 5

1.6 Thermal protection 6

1.7 Dimensions, weight and packaging 6

1.8 Standards compliance 6

1.9 Certifications 6

2. Wiring 7

2.1 Wiring specifications 7

2.1.1 General wiring specifications 7

2.1.2 Power cord requirements 7

2.1.3 Sample voltage drop calculation 8

2.2 Connections 8

2.2.1 DMX network options 9

2.2.2 LED outputs 11

2.2.3 LEDcode/NTC 12

2.2.4 0-10V 12

2.2.5 DALI 12

2.2.6 120-230V AC 12

3. Installing the POWERdrive 6060/R 13

3.1 Cable connections 13

3.2 Common practice for grounding LED wires 14

3.3 Cable trunk 15

4. Configuring POWERdrive 6060/R 16

4.1 Menu button combinations 16

4.2 Order of LED driver configuration 16

4.3 Setting the operation mode 17

4.4 Setting the LED output current and LED group configuration 17

3

Safety guidelines 20

Disclaimer 21

Warranty 22

4

1. Technical characteristics

1.1 Input characteristics

Input voltage AC

120-230V

Input current

6.3A max @ 120V / 60Hz
5A max @ 230V / 50Hz

Input frequency

50-60Hz

Power factor

>0.9 @ 25% load and higher

Total Harmonic Distortion

<20% between 2/3 load and full load

Efficiency @ full load

91.8%

Efficiency @ 2/3 load

91.2%

Inrush current

35A @ 115V AC
70A @ 230V AC

Surge protection

EN 61000-4-5 compliant

Standby power

12.5W @ 100V AC

12.8W @ 120V AC

14.4W @ 230V AC

Figure 1.1 Derating diagram

To avoid temperature rise affecting lifetime, it is recommended not to use configurations in the derating area of the diagram above. The green area
indicates the highest efficiency area of POWERdrive 6060/R.

Calculation examples in the high efficiency area, using the formula (number of LED outputs) * ( Iout ) * ( VLED )
Using all 32 LED outputs:

 32 LED outputs * 0.5A * 37.5V = 600W
 32 LED outputs * 0.45A * 41.6V = 599W
 32 LED outputs * 0.4A * 46.8V = 600W

Using 16 LED outputs:

 16 LED outputs * 1A * 37.5V = 600W
 16 LED outputs * 0.9A * 41.6V = 599W
 16 LED outputs * 0.8A * 46.8V = 600W

5

1.2 Output characteristics

LED outputs

32

LED output power

600W max

LED output voltage range

2-48V

LED output current range

200-1,050mA

LED output current resolution

Programmable in 50mA steps

LED output current accuracy

+/- 10%

1.3 Control characteristics

Control channels

1-32 over DMX/RDM, 1-4 over DALI, 1 over 0-10V

Dimming protocol

USITT DMX512A // RDM, DALI or 0-10V

Dimming range

100%-0%

Dimming method

Hybrid HydraDrive

Dimming curve

Linear, logarithmic, square

Driver configuration

via front display and menu buttons

Isolation 0-10V to line voltage input

1500V

Isolation 0-10V to LED output

3750V

0-10V current draw

2mA

1.4 Protection

LED output short

Yes

LED output cross short

Yes

Overload

Yes

Reverse polarity

Yes, for LED output

Restart after protection

1.5 Thermal characteristics

Ta operating range

-20 °C … +50 °C / -4 °F … +122 °F

Tc max

85 °C / 185 °F

Tc lifetime

78 °C / 172 °F

6

1.6 Thermal protection

External NTC thermistor

Throttling @ 70 °C / 158 °F (settable)

External NTC thermistor value

47kOhm

Recommended NTC thermistor

238164063473 (leaded)
NTCASCWE3473J (screw)

1.7 Dimensions, weight and packaging

L x W x H

482.6 x 325 x 44.5mm / 19 x 12.8 x 1.75in

Weight

6.3kg / 13 lb, 14.23 oz

Packaging

1 pc

Figure 1.2 POWERdrive 6060/R dimensions

1.8 Standards compliance

EN

EN 55022, EN 62386-101/102/207, EN 60929 Annex E

RoHS

RoHS2

1.9 Certifications

CE

Directives 2004/108/EC, 2006/95/EC, 2011/65/EU

UL

Pending

7

2. Wiring

2.1 Wiring specifications

2.1.1 General wiring specifications

Wire type

AWG20 – AWG16, 0.5-1.5mm2

Wire core type

Solid or stranded copper

Wire strip length

9mm, 0.35in

The maximum length of LED wiring is 100m / 328ft from LED output to LED load when using 16 AWG type wires.
Refer to the table below for the maximum LED wiring length for other wire types:

AWG value

20

19

18

17

16

Distance (m)

14

18

22

28

36

Distance (ft)

46

59

72

92

118

Please observe a voltage drop over long wire lengths: the longer the wire length between LED output and LED load, the lower the forward voltage is
that is available to you per LED output.

2.1.2 Power cord requirements

Europe excluding UK

certified according to EN50525 norm
CEE7 mains plug
IEC60320 C13 connector
H05VV F3 x 0.75mm2 cable

United Kingdom

certified according to EN50525 norm
BS1363A mains plug
IEC60320 C13 connector
H05VV F3 x 1.0mm2 cable

USA

UL listed
NEMA 5-15P mains plug
IEC60320 C13 connector
S 3x 18AWG/16AWG VCTF3x 0.75mm2 cable
Type SP-2, Type SPE-2, Type SPT-2, or heavier cord, minimum 1.5 m

(5 ft) in length