ELDAT RTM08916 Users Manual
USA/AUS Transmitter module RTM08
Model
5
V
D
C
(
+
)
G
N
D
T
r
a
n
s
m
i
s
s
i
o
n
A
c
t
i
v
i
t
yxy
z
w
T
r
a
n
s
m
i
s
s
i
o
n
c
o
d
e
{
6,0
1 2 3 4 5 6 7
Grid:
2.54 mm
Technical Details
Intended Use
Safety Advice
Before connecting and operating
the transmitter module, carefully
read through the operating instructions!
Note also the operating instructions of the
radio control(s)!
Have faulty transmitter modules checked by
the manufacturer!
Do not make any unauthorized alterations or
modifications to the transmitter module!
Installation instruction
Function
Coding
Group
Transmission
code
x y z
w
1
A
0 0 0 0 B
0 0 0
1
2
A
0 0 1 0 B
0 0 1
1 3 A
0 1 0 0 B
0 1 0
1
4
A
0 1 1 0 B
0 1 1
1
5
A
1 0 0 0 B
1 0 0
1
6
A
1 0 1
0
B
1 0 1
1 7 A
1 1 0
0
B
1 1 0
1 8 A
1 1 1 0 B
1 1 1
1
Start-Up
Disposal
Dispose of the waste product via a
collection point for electronic scrap
or via your specialist dealer.
Put the packaging material into the
recycling bins for cardboard, paper
and plastics.
Warranty
Conformity
Customer Service
RTM08E6008A01 916.50 MHz
Frequency: 916.50 MHz
Modulation: FSK
Power supply: 5 V DC
Standby current: max. 1,5 mA
Transmitting
current: max. 13 mA
Transmission
range: approx. 100 m at optimal
free field conditions
Operating
temperature: -20 °C to +60 °C
Dimension: 40 x 22 x 5,8 mm
The transmitter module may only be used
to operate radio controls.
The manufacturer does not assume any
liability for damage caused as a result of
improper or non-intended use!
Manufacturers of mobile, fixed or portable
devices incorporating this module are
advised to clarify any regulatory questions
and to have their complete product tested
and approved for FCC compliance. Since
the module is not shielded, the module
grantee bears the responsibility for test
evaluation to ensure that the module is
compliant in the host device.
The Transmitter Module RTM08 is a device designed for transmitting a maximum
of 16 different digital states. It is permanently under voltage.
The integrated micro controller carries out
all necessary important functions for the
transmission process. The maximal transmission time is 36 seconds.
In case PIN 3 receives a high a radiogram
according to the coding at PIN 4-7 is
transmitted.
Waste electrical products should not be
disposed of with household waste!
Within the statutory warranty period we
undertake to rectify free of charge by
repair or replacement any product defects
arising from material or production faults.
Any non-authorized alterations or modifications to the product shall render this
warranty null and void.
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) this device
may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
If, despite correct handling, faults or malfunctions occur or if the product was damaged, please contact your retailer or the
manufacturer.
ELDAT GmbH
Im Gewerbepark 14
15711 Königs Wusterhausen
Germany
Phone: + 49 (0) 33 75 / 90 37-0
Fax: + 49 (0) 33 75 / 90 37-90
Internet: www.eldat.de
E-Mail: info@eldat.de
Manufacturers integrating the transmitter
module RTM08 into a host device may
affix an additional permanent label on their
host device referring to the enclosed mod-
ule: “Contains Transmitter Module FCC ID
RZZRTM08916”.
The transmitter module is equipped with a
permanently attached antenna with is
soldered into the printed circuit board. To
meet the FCC’s RF exposure rules the
system antenna may not be co-located or
operating in conjunction with any other
antenna.
UM164043 0118 GB
0 = GND, 1 = nc
1. Connect the module as follows:
Power Supply:
PIN1: 5 V DC
PIN2: GND
Kanäle:
PIN4-7: transmission code
(see coding)
PIN 3: (High) transmission activity
Activate the transmission activity (PIN3) only after setting
the codings x, y, z, w (PIN4 to
PIN7).
2. Register the transmission code with
the radio control. Please read the operating instructions supplied with the
radio controls.
Loading...