en
Elcometer 213/2
R
en
ThThis product meets the Electromagnetic Compatibility Directive.
The product is Class B, Group 1 ISM equipment according to CISPR 11
R
en
CONTENTS
Section Page
1 About your gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
2 Fitting a battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
3 Fitting a probe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
4 Taking a reading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
5 Changing measurement units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
R
en
Thank you for your purchase of this Elcometer 213/2 Digital Thermometer. Welcome to Elcometer.
Elcometer are world leaders in the design, manufacture and supply of inspectio n equipment for coatings
and concrete. Our products cover all aspects of coating inspection, from development, through application
to post application inspection.
Your Elcometer 213/2 Digital Thermometer is a world beating product. With the purchase of this product you
now have access to the worldwide service and support network of Elcometer. For more information visit our
website at www.elcometer.com
1 ABOUT YOUR GAUGE
R
en
1.2 WHAT THE BOX CONTAINS
• Elcometer 213/2 Digital Thermometer with battery fitted
• Operating instructions
Note: A probe is not supplied with the thermometer. Probes must be
ordered separately - see “Spare parts and accessories” on page 8.
The Elcometer 213/2 Digital Thermometer is packed in a cardboard and
foam package. Please ensure that this packaging is disposed of in an
environmentally sensitive manner. Please consult your local
R
en
To change the battery:
1. Using a Posidrive (crosshead) screwdriver, remove the two battery compartment cover retaining
screws on the base of the gauge and lift away the cover.
2. Remove the battery by pushing it to one side.
3. Fit the new battery into the battery clips taking care to observe the correct polarity.
4. Replace the battery compartment cover ensuring that the seals are not damaged and are correctly
positioned.
5. Tighten the retaining screws firmly to ensure that the seals are compressed and will provide a water-
R
en
4 TAKING A READING
1. To switch on the gauge, press .
2. Apply the tip of the probe to the substance, medium or surface to be measured.
The reading on the display may take a number of seconds to stabilise depending on the nature of the
measurement and the sensitivity of the probe.
3. If required, to freeze the reading on the display, press . ‘HOLD’ is shown on the display.
R
en
5 CHANGING MEASUREMENT UNITS
To change the instrument units from °C to °F or vice versa:
1. Switch off the gauge.
2. Press but do not release the button.
3. While continuing to press , press to switch on the gauge.
R
en
7 MAINTENANCE/STORAGE
You own one of the finest digital thermometers in the world. If looked after, it will last a lifetime.
• Be careful not to scratch the LCD screen or break the glass screen.
• Do not subject the gauge to a strong impact.
• Clean the gauge with a soft, dry cloth such as those made to clean eyeglasses. Do not use solvents!
This gauge incorporates a Liquid Crystal Display. If the display is heated above 50°C (120°F) it may
be damaged. This can happen if the gauge is left in a car parked in strong sunlight.
Regular calibration checks over the life of the gauge are a requirement of quality management procedures,
R
en
8 SPARE PARTS AND ACCESSORIES
The following spare parts and accessories are available direct from Elcometer or your local supplier:
Beschrijving Reeks Artikelnummer
Magnetic Surface Probe, 13mm
(0.51”) Diameter
-50°C to 150°C (-58°F to 302°F) T99911728
R
en
9 TECHNICAL SPECIFICATIONS
Measurement Range: -49°C to +1372°C (-56°F to +2500°F)
Resolution: 0.1°C (0.1°F) up to +299.9°C (+ 599.9°F)
1°C (1°F) above +299.9°C (+ 599.9°F)
Accuracy: ±1% of the reading ±1 digit
Probe: ‘K type’ Thermocouple
Ambient Temperature: 0°C to +50°C (0°F to +122°F)
R
en
10 RELATED EQUIPMENT
In addition to the Elcometer 213/2 Digital Thermometer, Elcometer produces a wide range of environmental
measuring equipment and other equipment for measuring the characteristics of surface coatings.
Users of the Elcometer 213/2 Digital Thermometer may also benefit from the following Elcometer products:
• Elcometer 214 Infrared Digital Thermometer
• Elcometer 214L Infrared Digital Thermometer with Laser alignment
• Elcometer 212 Digital Pocket Thermometer
• Elcometer 113 Magnetic Thermometer
Loading...