© 2016 EL-CELL GmbH
PAT-Single-Stand
Docking station for PAT series test cells
User Manual
Release 1.41
User Manual PAT-Single-Stand
Release 1.41
The information in this manual has been carefully checked and believed to be accurate;
however, no responsibility is assumed for inaccuracies.
EL-CELL GmbH maintains the right to make changes without further notice to products
described in this manual to improve reliability, function, or design. EL -CELL GmbH does not
assume any liability arising from the use or application of this product.
EL-CELL GmbH
Tempowerkring 8
21079 Hamburg - Germany
phone: +49 40 79012-737
fax: +49 40 79012-736
e-mail: in fo@ el- cel l.c om
web: www.el-cell. co m
Page 2 of 9
User Manual PAT-Single-Stand
Release 1.41
Content
1 Product description ...................................................................................................................................... 4
2 Installation ....................................................................................................................................................... 5
3 Cleaning ........................................................................................................................................................... 5
4 Operation modes ........................................................................................................................................... 6
5 Cable colors and naming conventions .................................................................................................... 7
6 Unpacking........................................................................................................................................................ 8
7 Technical data ................................................................................................................................................ 8
8 Spare parts ...................................................................................................................................................... 8
9 Technical support .......................................................................................................................................... 9
10 Warranty ........................................................................................................................................................ 9
Page 3 of 9
User Manual PAT-Single-Stand
Release 1.41
1 Product description
PAT-Single-Stand
PAT-Cell
The PAT-Single-Stand is the docking station for a single PAT series test cell. When docked into
the PAT-Single-Stand, the test cell may be tested by any potentiostat or battery tester.
The compatible test cells and the PAT-Core concept are covered in detail by other manuals:
(http://el-cell.com/downloads/downloads-manuals).
Features
Docking station for one PAT series test cell, ready for connection to a potentiostat or
battery tester channel.
Compatible with the following test cells:
PAT-Cell
PAT-Cell-Press
Compatible with all of today’s potentiostats and battery testers.
Page 4 of 9
User Manual PAT-Single-Stand
Release 1.41
connection of 2 mm banana plugs are included.
2 Installation
Sub-D F15 Pin #
1 2 4 5 10
Signal
1S
2S R 2
1
Place the PAT-Single-Stand on a flat, dry and clean surface, for example on a bench top, inside
a temperature chamber or a glove box. Then conncet the cell cable of your potentiostat or battery
tester channel to the banana sockets at the front of the PAT-Single-Stand.
Pin-Out of Sub-D F15 HD Connector “Cell” at PAT-Single
-Stand
The "CELL" socket may optionally be used
for connecting the PAT-Single-Stand to a
potentiostat (instead of connecting to the
banana sockets at the front). The "AUX"
socket is for future use.
4 mm banana sockets for connection to the cell cable
of a potentiostat or battery tester. Adapters for
3 Cleaning
Wipe the PAT-Single-Stand with a moist tissue. Do not use aggressive chemicals for cleaning.
Protect the PAT-Single-Stand from dust and moisture.
Page 5 of 9
User Manual PAT-Single-Stand
Release 1.41
4 Operation modes
Operation mode 1: Cell voltage control (1 vs 2)
PAT-Single-Stand
1
1S 2 2S
R
Potentiostat
WE
WE-Sense
CE
RE
(CE-Sense)
Battery tester
Plus
Plus-Sense
Minus
Minus-Sense
-
Operation mode 2: Half cell voltage control (1 vs R)
PAT-Single-Stand
1
1S 2 2S
R
Potentiostat
WE
WE-Sense
CE
(CE-Sense)
RE
Battery tester
Plus
Plus-Sense
Minus
-
Minus-Sense
Operation mode 3: Half cell voltage control (2 vs R)
PAT-Single-Stand
1
1S 2 2S
R
Potentiostat
CE
(CE-Sense)
WE
WE-Sense
RE
Battery tester
Minus
-
Plus
Plus-Sense
Minus-Sense
Connect the cell cable of your potentiostat or battery tester channel to the banana sockets at the front
of the PAT-Single-Stand. For the different operation modes, see the table below.
Page 6 of 9
User Manual PAT-Single-Stand
Release 1.41
5 Cable colors and naming conventions
Exemplary
potentiostat
WE
WE-Sense
CE
CE-Sense
RE
BioLogic
SP, VMP, VSP, MPG
WE
Red cable
Ref1
Red cable
CE
Blue cable
Ref3
Blue cable
Ref2
White cable
Gamry Instruments
Reference 600TM and 3000TM,
Interface 5000
Green cable
Blue cable
Red cable
Orange cable
White cable
Ivium Technologies
IviumStat, Ivium-n-Stat,
CompactStat, Vertex
W
Red cable
S
White cable
C
Black cable
Not available
R
Blue cable
Metrohm Autolab
PGSTAT Series
WE
Red cable
S
Red cable
CE
Black cable
Not available
RE
Blue cable
Princeton Applied Research
PARSTAT 2273
WKNG
Green cable
SENSE
Grey cable
CNTR
Red cable
Not available
REF
White cable
WonATech
ZIVE SERIES
WE
Green cable
WS
Blue cable
CE
Red cable
Not available
RE
White cable
The naming convention and color codes of the potentiostat´s cell cable leads are not
standardized between different manufacturers. The table below is an incomplete list of some
popular instruments.
Important note: The application of our test cells is not limited to the potentiostats listed
below. Our test cells can be used with all other potentiostats as well.
Page 7 of 9
User Manual PAT-Single-Stand
Release 1.41
6 Unpacking
Check the contents of the packages against the list given below to verify that you have
received all of the required components. Contact EL-CELL, if anything is missing or damaged.
NOTE: Damaged shipments must remain within the original packaging for freight company
inspection.
List of Components
PAT-Single-Stand (without PAT-Cell) ECE1-00-0010-A
6 x adapter male 4 mm to female 2 mm ELT9081
7 Technical data
Operating temperature: -20 to +70°C
Humidity: non condensing
Dimensions: 105 mm (width) x 113 mm (depth) x 80/110 mm (height without/ with PAT-Cell)
Weight: 0.56/0.96 kg (without/with PAT-Cell)
Protection Class: IP20 according to EN 60529
8 Spare parts
Adapter male 4 mm to female 2 mm ELT9081
Page 8 of 9
User Manual PAT-Single-Stand
Release 1.41
9 Technical support
Technical support for this product is exclusively provided by EL-CELL GmbH.
EL-CELL GmbH
Tempowerkring 8
21079 Hamburg - Germany
phone: +49 40 79012-737
fax: +49 40 79012-736
e-mail: in fo@ el- cel l.c om
web: www.el-cell. co m
10 Warranty
For a period of one year from the date of shipment, EL -CELL GmbH (hereinafter Seller)
warrants the goods to be free from defect in material and workmanship to the original
purchaser. During the warranty period, Seller agrees to repair or replace defective and/or
nonconforming goods or parts without charge for mate rial or labor, or, at the Seller’s option,
demand return of the goods and tender repayment of the price. Buyer’s exclusive remedy is
repair or replacement of defective and nonconforming goods, or, at Seller’s option, the
repayment of the price.
Seller excludes and disclaims any liability for lost profits, personal injury, interruption of
service, or for consequential incidental or special damages arising out of, resulting from, or
relating in any manner to these goods.
This Limited Warranty does not cover defects, damage, or nonconformity resulting from
abuse, misuse, neglect, lack of reasonable care, modification, or the attachment of improper
devices to the goods. This Limited Warranty does not cover expendable items. This warranty is
void when repairs are performed by a non-authorized person or service center. At Seller’s
option, repairs or replacements will be made on site or at the factory. If repairs or
replacements are to be made at the factory, Buyer shall return the goods prepaid and bear all
the risks of loss until delivered to the factory. If Seller returns the goods, they will be delivered
prepaid and Seller will bear all risks of loss until delivery to Buyer. Buyer and Seller agree that
this Limited Warranty shall be governed by and construed in accordance with the laws of
Germany.
The warranties contained in this agreement are in lieu of all other warranties expressed or
implied, including the warranties of merchantability and fitness for a particular purpose.
This Limited Warranty supersedes all prior proposals or representations oral or written and
constitutes the entire understanding regarding the warranties made by Seller to Buyer. This
Limited Warranty may not be expanded or modified except in writing signed by the parties
hereto.
Page 9 of 9
Loading...