Page 1
Built-in Oven
OB60S3, OB60S4, OB60S7,
OB60SL & OB60B
models
NZ AU
INSTALLATION INSTRUCTIONS
590498 B / 1104554-ß1 03.14
Page 2
2
IMPORTANT!
SAVE THESE INSTRUCTIONS
The models shown in this installation guide may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country, please go to
our website listed on the cover or contact your local ELBA by Fisher & Paykel dealer.
IMPORTANT SAFETY INSTRUCTIONS
●
To avoid hazard, follow these instructions carefully before installing or using this
appliance.
●
Please make this information available to the person installing the appliance - doing so
could reduce your installation costs.
●
This appliance must be installed and connected to the mains power supply only by a
suitably qualified person according to these installation instructions and in compliance
with any applicable local building and electricity regulations. Failure to install the
appliance correctly could invalidate any warranty or liability claims.
●
If the power supply cable is damaged, it must be replaced by the manufacturer, its
service agent or similarly qualified person in order to avoid a hazard.
WARNING!
Electrical Shock Hazard
Always disconnect the appliance from the mains power supply before
carrying out any maintenance or repairs.
Connection to a good earth wiring system is essential and mandatory.
Alterations to the domestic wiring system must only be made by a
qualified electrician.
Failure to follow this advice may result in electrical shock or death.
WARNING!
Hot Surface Hazard
Take care - panel edges are sharp.
Failure to use caution could result in injury or cuts.
WARNING!
Fire Hazard
Do not use adapters, reducers, or branching devices to connect this appliance
to the mains power supply.
Failure to follow this advice may result in overheating, burning, or fire.
!
!
!
1 SAFETY AND WARNINGS
Page 3
1
2 PRODUCT DIMENSIONS (OB60S MODELS)
A
CF
B
E
G
H
D
FRONT SIDE
TOP
OB60S3
OB60S4
OB60S7
Product Dimensions mm
A
Overall height* of product 597
B
Overall width of product 595
C
overall depth of product (excluding handle and knobs) 567
D
Height of chassis 582
E
Width of chassis 556
F
Depth of chassis 545
G
Depth of oven frame and control panel
(=distance between front of chassis and front of oven door, excl. knobs)
22
H
depth of oven door when fully open
(measured from front of control panel)
435
*All height measurements include mounted feet.
Page 4
2
2 CABINETRY DIMENSIONS (OB60S MODELS)
I
J
K
L
M
Electrical supply
16-20 mm
min. 2.5 mm
TOPSIDE
OB60S3
OB60S4
OB60S7
Cabinetry Dimensions mm
I
Minimum inside width of cavity 560
J
Overall width of cavity 600
K
Inside height of cavity 585
L
Overall height of cavity 600
M
Minimum inside depth of cavity 550
Note: If installing a cooktop above the oven, ensure adequate clearance is provided for the cooktop as per the cooktop manufacturer’s
instructions.
Page 5
3
2 PRODUCT DIMENSIONS (OB60B MODELS)
A
CF
B
E
G
H
D
H
OB60B
Product Dimensions mm
A
Overall height* of product 888
B
Overall width of product 595
C
overall depth of product (excluding handle and knobs) 567
D
Height of chassis 874
E
Width of chassis 556
F
Depth of chassis 545
G
Depth of oven frame and control panel
(=distance between front of chassis and front of oven door, excl. knobs)
22
H
depth of oven door when fully open
(measured from front of control panel)
upper 261
lower 435
*All height measurements include mounted feet.
FRONT
SIDE
TOP
Page 6
4
2 CABINETRY DIMENSIONS (OB60B MODELS)
OB60B
Cabinetry Dimensions mm
I
Minimum inside width of cavity 560
J
Overall width of cavity 600
K
Inside height of cavity 877
L
Overall height of cavity 893
M
Minimum inside depth of cavity 550
K
L
M
I
J
Electrical supply
16-20 mm
min. 2.5 mm
SIDE
TOP
Page 7
5
2 PRODUCT DIMENSIONS (OB60SL MODELS)
A
CF
B
E
G
H
D
16-20 mm
FRONT SIDE
TOP
OB60SL
Product Dimensions mm
A
Overall height* of product 597
B
Overall width of product 595
C
overall depth of product (excluding handle and knobs) 567
D
Height of chassis 582
E
Width of chassis 556
F
Depth of chassis 545
G
Depth of oven frame and control panel
(=distance between front of chassis and front of oven door, excl. knobs & door hinge)
22
H
Maximum Depth of oven door when fully open
(measured from front of control panel)
595
*All height measurements include mounted feet.
Page 8
6
2 CABINETRY DIMENSIONS (OB60SL MODELS)
OB60SL
Cabinetry Dimensions mm
I
Minimum inside width of cavity 560
J
Overall width of cavity 600
K
Inside height of cavity 585
L
Overall height of cavity 600
M
Minimum inside depth of cavity 550
Note: If installing a cooktop above the oven, ensure adequate clearance is provided for the cooktop as per the cooktop manufacturer’s
instructions.
IMPORTANT!
Doors of adjacent
cabinetry may need
adjusting to allow
the oven door to
open properly: a
minimum clearance
of 5mm is
recommended.
I
J
K
L
M
Electrical supply
16-20 mm
min. 2.5 mm
16-20 mm
min. 5 mm
SIDE
TOP
Proud Installation
Flush Installation
Page 9
7
3 PRIOR TO INSTALLATION
LOWER TRIM
Feet
Before you install the oven, make sure that
●
the benchtop and oven cavity are square and level, and are the required dimensions
●
the installation will comply with all clearance requirements and applicable standards and regulations
●
a suitable isolating switch providing full disconnection from the mains power supply is incorporated in the permanent wiring, mounted and positioned to comply with the local wiring rules and
regulations. The isolating switch must be of an approved type and provide a 3 mm air gap contact separation in all poles (or in all active [phase] conductors if the local wiring rules allow for
this variation of the requirements)
●
the isolating switch will be easily accessible to the customer with the oven installed
●
there is at least 1.5 m (and not more than 2 m) free length of power supply cable within the cavity for ease of installation and servicing
●
the oven connection socket (if fitted) is outside the cavity if the oven is flush to the rear wall
●
the oven will rest on a surface that can support its weight
●
the height from the floor suits the customer
●
you consult local building authorities and by-laws if in doubt regarding installation
IMPORTANT!
Some environmental factors and cooking habits can cause condensation in and around the oven during use. To protect surrounding cabinetry from possible damage caused by frequent or
excessive condensation, we recommend moisture-proofing the oven cavity.
IMPORTANT!
Do not lift the oven by the door handle.
●
Remove all packaging and dispose of it responsibly. Recycle items that you can.
●
Place the unpacked oven onto wooden blocks or similar supports to prevent damaging the
lower trim. You may remove the feet, but ensure the oven does not sit on the lower trim
IMPORTANT!
The lower trim ensures correct air circulation and allows the door to open and close
without obstruction. The manufacturer does not accept any responsibility for damage
resulting from incorrect installation.
OVEN DOOR
LOWER TRIM
AIR FLOW
●
Depending on the model, the door
is either left- or right-hinged. When
determining the location of the oven,
ensure there will be enough space for the
door to open to its full extent.
●
This is to ensure that you have access to
the fixing screw holes on the hinged side
when securing the oven to the cabinetry.
Fixing screw holes
4 UNPACKING THE OVEN 5 OVEN LOCATION (OB60SL ONLY)
Page 10
8
6 ELECTRICAL CONNECTION 7 SECURING THE OVEN TO THE CABINETRY
IMPORTANT!
●
This oven must be connected to the mains power supply only by a suitably qualified
person.
●
This oven must be earthed.
Before connecting the oven to the mains power supply, check that
●
the domestic wiring system is suitable for the power drawn by the oven
(as specified on the rating plate)
●
the voltage corresponds to the value given on the rating plate.
OB60SL, OB60S3, OB60S4 and OB60S7 models
Model code Power Voltage
OB60SL 3070W 220-240V~
OB60S3 2250W 220-240V~
OB60S4 3070W 220-240V~
OB60S7 3070W 220-240V~
OB60B models
Model code Power Voltage
OB60B 4400W 220-240V~
E
N
L
1
(L )
2
Unhook to open cover
1
2
Unscrew to open
cable clamp
1 Position the oven in the prepared cavity.
IMPORTANT!
Do not lift the oven by the door handle.
2 Open the oven door fully.
3 Use the supplied screws to secure the oven to the cabinetry.
IMPORTANT!
●
Do not over-tighten the screws.
●
Do not seal the oven into the cabinetry with silicone or glue. This makes future servicing
difficult. Fisher & Paykel will not cover the costs of removing the oven, or of damage
caused by this removal.
2.5 mm
E
N
L
1
(L )
2
Green & Yellow
(Earth)
Brown (Live)
Blue (Neutral)
N
L
D
1
2
Unscrew to
remove cover
plate
Unscrew to remove
cable clamp
OB60S3, OB60S4, OB60S7 and OB60B models
OB60SL models
Page 11
9
8 FINAL CHECKLIST
TO BE COMPLETED BY THE INSTALLER
Make sure the oven is level and securely fitted to the cabinetry and the oven door opens and closes freely.
Make sure all the internal packaging has been removed from the oven cavity.
Make sure all oven vents and openings are clear and are free of any obstruction/damage.
OB60S3, OB60S4, OB60S7, OB60B models: Check the lower trim is still undamaged - open the oven door slowly to its fully open position and check if there is adequate clearance
between the bottom of the door and the lower trim. This is to ensure correct air circulation. Should the lower trim become damaged, straighten it and ensure the oven door opens
fully without obstruction.
OB60SL models: Check there is adequate clearance between the bottom of the door and the lower trim. This is to ensure correct air circulation. Should the lower trim become
damaged, straighten it and ensure the oven door opens fully without obstruction.
Check that the power supply cable does not touch any metal parts that can become hot during use.
Have you affixed the supplied duplicate data plate label on an adjacent
surface accessible to the customer?
Make sure that the isolating switch is easily accessible by the customer.
Turn the power to the oven on. On some models, the display should light up and show
.
Advise the customer to follow the instructions in their user guide in section ‘First use’.
Complete and keep for safe reference:
Model
Serial No.
Purchase Date
Purchaser
Dealer Address
Installer’s Name
Installer’s Signature
Installation Company
Installation Date
Page 12
590498 B / 1104554-ß1 03.14
www.elba.co.nz
www.elba.com.au
Copyright © Fisher & Paykel 2014. All rights reserved.
The product specifications in this booklet apply to the specific
products and models described at the date of issue. Under our
policy of continuous product improvement, these specifications
may change at any time. You should therefore check with your
Dealer to ensure this booklet correctly describes the product
currently available.
NZ AU
Loading...