Elation Fuze Par Z120 Users Manual

ELATION

|

|

FUZE PAR Z120 IP™

FUZE PAR Z120 IP

™

user manual

user manual 

CH12: sRGBWI / CH:13 RGBW

www.elationlighting.com

©2016 ELATION PROFESSIONAL all rights reserved. Information, specifications,
diagrams, images, and instructions herein are subject to change without notice.
ELATION PROFESSIONAL logo and identifying product names and numbers herein
are trademarks of ELATION PROFESSIONAL. Copyright protection claimed includes
all forms and matters of copyrightable materials and information now allowed by
statutory or judicial law or hereinafter granted. Product names used in this
document may be trademarks or registered trademarks of their respective
companies and are hereby acknowledged. All non-ELATION brands and product
names are trademarks or registered trademarks of their respective companies.

ELATION PROFESSIONAL and all affiliated companies hereby disclaim any and all
liabilities for property, equipment, building, and electrical damages, injuries to any
persons, and direct or indirect economic loss associated with the use or reliance of
any information contained within this document, and/or as a result of the improper,
unsafe, insufficient and negligent assembly, installation, rigging, and operation of
this product.

Elation Professional USA | 6122 S. Eastern Ave. | Los Angeles, CA. 90040

323-582-3322 | 323-832-9142 fax | www.elationlighting.com | [e-mail]

Elation Professional B.V. | Junostraat 2 | 6468 EW Kerkrade, The Netherlands

[phone] | [phone] fax | www.elationlighting.eu | [e-mail]

DOCUMENT VERSION

Please check www.elationlighting.com for the latest revision/update of this manual.

DMX

Channel Modes

Notes

Updated max power

consumption and max number of

units for power linking specs.

Date

08/12/16

Document

Version

1.1

Software

Version

IU ≥1.03

2U ≥1.03

CH:04 RGBW / CH:04 HSI

CH:05 HSI+ / CH:06 RGBW

CH:07 sRGBWI / CH:07 RGBW

CH:08 RGBW / CH:09 RGBW

CH:10 16Bit / CH:10 HSI

2 FUZE PAR Z120 IP™ User Manual

CONTENTS

General Information

4

Warranty

7

Safety Instructions and Guidelines

8

Overview

10

Installation

11

System Menu

15

DMX Channel Functions And Values

19

Cleaning and Maintenance

23

Technical Specifications

24

Optional Accessories

27

www.elationlighting.com

3 FUZE PAR Z120 IP™ User Manual

www.elationlighting.com

GENERAL INFORMATION

INTRODUCTION

Congratulations, you have just purchased one of the most innovative and

reliable IP65 rated lighting fixtures on the market today! This fixture has been

designed to perform reliably for years when the guidelines in this booklet are

followed. Please read and understand the instructions in this manual carefully

and thoroughly before attempting to operate this unit. These instructions contain

important information regarding safety during use and maintenance.

IP65 RATED

An IP rated lighting fixture is one, which is commonly installed in outdoor
environments and has been designed with an enclosure that effectively protects
the ingress (entry) of external foreign objects such as dust and water. The
International Protection (IP) rating system is commonly expressed as "IP" (Ingress
Protection) followed by two numbers (i.e. IP65) where the numbers define the
degree of protection. The first digit (Foreign Bodies Protection) indicates the
extent of protection against particles entering the fixture and the second digit
(Water Protection) indicates the extent of protection against water entering the
fixture. An IP65 rated lighting fixture is one, which has been designed and tested
to protect against the ingress of dust (6) and high-pressure water jets from any
direction (5).

MARINE/COASTAL ENVIRONMENT INSTALLATIONS!

Please note although this fixture is IP rated, the fixture is NOT suitable for marine
and/or coastal environment installations. Installing this fixture in a marine and/or
coastal environment may cause corrosion and/or excessive wear to the interior
and/or exterior components of the fixture. Damages and/or performance
issues resulting from installation in a marine and/or coastal environment will void
the manufactures warranty and will NOT be subject to any warranty claims
and/or repairs.

ENSURE ALL CONNECTIONS AND END CAPS ARE PROPERLY SEALED WITH A

NON-CONDUCTIVE DIELECTRIC GREASE (AVAILABLE AT MOST ELECTRICAL

SUPPLIERS) TO PREVENT WATER INGRESS/CONDENSATION AND/OR CORROSION.

OPTIONAL CORROSION- RESISTANT COATING

Optional Corrosion-Resistant Coatings may be available for this fixture.
Please consult your Elation Professional sales representative for details.

4 FUZE PAR Z120 IP™ User Manual

www.elationlighting.com

UNPACKING

Every fixture has been thoroughly tested and has been shipped in perfect

operating condition. Carefully check the shipping carton for damage that may

have occurred during shipping. If the carton appears to be damaged, carefully

inspect your unit for damage and be sure all accessories necessary to operate

the unit have arrived intact. In the event damage has been found or parts are

missing, please contact our customer support team for further instructions. Please

do not return this unit to your dealer without first contacting customer support at

the number listed below. Please do not discard the shipping carton in the trash.

Please recycle whenever possible.

BOX CONTENTS

 (1) Gel Frame

 (1) Gel Frame/Barn Door Holder

 (1) Barn Door

 (1) powerCON TRUE1 Cable

CUSTOMER SUPPORT

Elation Professional® provides a customer support line, to provide set up help and

to answer any question should you encounter problems during your set up or

initial operation. You may also visit us on the web at www.elationlighting.com for

any comments or suggestions. For service related issue please contact Elation

Professional®.

ELATION SERVICE USA - Monday - Friday 8:00am to 5:00pm PST

Voice: 323-582-3322 Fax: [phone]

E-mail: [e-mail]

ELATION SERVICE EUROPE - Monday - Friday 08:30 to 17:00 CET

Voice: [phone] Fax: [phone]

E-mail: [e-mail]

5 FUZE PAR Z120 IP™ User Manual

www.elationlighting.com

WARRANTY REGISTRATION

Please complete and mail in the enclosed warranty card or register online:

http://www.elationlighting.com/Login.aspx to validate your purchase. All

returned service items whether under warranty or not, must be freight pre-paid

and accompany a return authorization (R.A.) number. The R.A. number must be

clearly written on the outside of the return package. A brief description of the

problem as well as the R.A. number must also be written down on a piece of

paper and included in the shipping container. If the unit is under warranty, you

must provide a copy of your proof of purchase invoice. Items returned without a

R.A. number clearly marked on the outside of the package will be refused and

returned at customer’s expense. You may obtain a R.A. number by contacting

customer support.

IMPORTANT NOTICE!

There are no user serviceable parts inside this unit. Do not attempt any repairs

yourself; doing so will void your manufactures warranty. Damages resulting from

modifications to this fixture and/or the disregard of safety and general user

instructions found in this user manual void the manufactures warranty and are

not subject to any warranty claims and/or repairs.

6 FUZE PAR Z120 IP™ User Manual

www.elationlighting.com

LIMITED WARRANTY

A. Elation Professional® hereby warrants, to the original purchaser, Elation Professional® products to
be free of manufacturing defects in material and workmanship for a period of two years (730 days),
and Elation Professional® product rechargeable batteries to be free of manufacturing defects in
material and workmanship for a period of six months (180 days), from the original date of purchase.
This warranty excludes discharge lamps and all product accessories. This warranty shall be valid only
if the product is purchased within the United States of America, including possessions and territories. It
is the owner’s responsibility to establish the date and place of purchase by acceptable evidence, at
the time service is sought.
B. For warranty service, send the product only to the Elation Professional® factory. All shipping
charges must be pre-paid. If the requested repairs or service (including parts replacement) are within
the terms of this warranty, Elation Professional® will pay return shipping charges only to a designated
point within the United States. If any product is sent, it must be shipped in its original package and
packaging material. No accessories should be shipped with the product. If any accessories are
shipped with the product, Elation Professional® shall have no liability what so ever for loss and/or or
damage to any such accessories, nor for the safe return thereof.
C. This warranty is void if the product serial number and/or labels are altered or removed; if the
product is modified in any manner which Elation Professional® concludes, after inspection, affects
the reliability of the product; if the product has been repaired or serviced by anyone other than the
Elation Professional® factory unless prior written authorization was issued to purchaser by Elation
Professional®; if the product is damaged because not properly maintained as set forth in the product
instructions, guidelines and/or user manual.
D. This is not a service contract, and this warranty does not include any maintenance, cleaning or
periodic check-up. During the periods as specified above, Elation Professional® will replace
defective parts at its expense, and will absorb all expenses for warranty service and repair labor by
reason of defects in material or workmanship. The sole responsibility of Elation Professional® under
this warranty shall be limited to the repair of the product, or replacement thereof, including parts, at
the sole discretion of Elation Professional®. All products covered by this warranty were manufactured
after January 1, 1990, and bare identifying marks to that effect.
E. Elation Professional® reserves the right to make changes in design and/or performance
improvements upon its products without any obligation to include these changes in any products
theretofore manufactured.
F. No warranty, whether expressed or implied, is given or made with respect to any accessory
supplied with the products described above. Except to the extent prohibited by applicable law, all
implied warranties made by Elation Professional® in connection with this product, including
warranties of merchantability or fitness, are limited in duration to the warranty periods set forth above.
And no warranties, whether expressed or implied, including warranties of merchantability or fitness,
shall apply to this product after said periods have expired. The consumer’s and/or dealer’s sole
remedy shall be such repair or replacement as is expressly provided above; and under no
circumstances shall Elation Professional® be liable for any loss and/or damage, direct and/or
consequential, arising out of the use of, and/or the inability to use, this product.
G. This warranty is the only written warranty applicable to Elation Professional® products and
supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore published.

7 FUZE PAR Z120 IP™ User Manual

www.elationlighting.com

SAFETY INSTRUCTIONS AND GUIDELINES

This fixture is an extremely sophisticated piece of electronic equipment. To

guarantee a smooth operation, it is important to follow all instructions and guidelines

in this manual. The manufacturer of this device is not responsible for injury and/or

damages resulting from the misuse of this fixture due to the disregard of the

information printed in this manual. Only qualified and/or certified personnel should

perform installation of this fixture and only the original rigging parts (omega brackets)

included with this fixture should be used for installation. Any modifications to the

fixture and/or the mounting hardware included will void the original manufactures

warranty and increase the risk of damage and/or personal injury.

PROTECTION CLASS 1 - FIXTURE MUST BE PROPERLY GROUNDED

DO NOT PLUG FIXTURE INTO A DIMMER PACK!

NEVER OPEN THIS FIXTURE WHILE IN USE!

UNPLUG POWER BEFORE SERVICING FIXTURE!

NEVER TOUCH FIXTURE DURING OPERATION, AS IT MAY BE HOT!

KEEP FLAMMABLE MATERIALS AWAY FROM FIXTURE!

NEVER LOOK DIRECTLY INTO THE LIGHT SOURCE!

RETINA INJURY RISK - MAY INDUCE BLINDNESS!

SENSITIVE PERSONS MAY SUFFER AN EPILEPTIC SHOCK!

ENSURE ALL CONNECTIONS AND END CAPS ARE PROPERLY SEALED

WITH A DIELECTRIC GREASE (AVAILABLE AT MOST ELECTRICAL

SUPPLIERS) TO PREVENT WATER CORROSION AND/OR ELECTRICAL

SHORT CIRCUIT.

8 FUZE PAR Z120 IP™ User Manual

www.elationlighting.com

SAFETY INSTRUCTIONS AND GUIDELINES

 DO NOT TOUCH the fixture housing during operation. Turn OFF the power and

allow approximately 15 minutes for the fixture to cool down before serving.

 DO NOT shake fixture, avoid brute force when installing and/or operating fixture.

 DO NOT operate fixture if the power cord has become frayed, crimped and/or

damaged. If the power cord is damaged, replace it immediately with a new one

of similar power rating.

 DO NOT block any air ventilation slots. All fan and air inlets must remain clean and

never blocked. Allow approx. 6” (15cm) between fixture and other devices or a

wall for proper cooling.

 When installing fixture in a suspended environment, always use mounting

hardware that is no less than M10 x 25 mm, and always install fixture with an

appropriately rated safety cable.

 Always disconnect fixture from main power source before performing any type of

service and/or cleaning procedure. Only handle the power cord by the plug

end, never pull out the plug by tugging the wire portion of the cord.

 During the initial operation of this fixture, a light smoke or smell may emit from the

interior of the fixture. This is a normal process and is caused by excess paint in the

interior of the casing burning off from the heat associated with the lamp and will

decrease gradually over time.

 Consistent operational breaks will ensure the fixture will function properly for

many years to come.

 Use the original packaging and materials to transport the fixture in for service.

9 FUZE PAR Z120 IP™ User Manual

OVERVIEW

www.elationlighting.com

SAFETY CABLE RIGGING POINT

10 FUZE PAR Z120 IP™ User Manual

INSTALLATION

Keep fixture at least 5.0 ft (1.5m) away from any

A qualified electrician should be used for all

www.elationlighting.com

FLAMMABLE MATERIAL WARNING

flammable materials, decorations, pyrotechnics, etc.

ELECTRICAL CONNECTIONS

electrical connections and/or installations.

CAUTIONS

ENSURE ALL CONNECTIONS AND END CAPS ARE PROPERLY SEALED WITH A

DIELECTRIC GREASE (AVAILABLE AT MOST ELECTRICAL SUPPLIERS) TO PREVENT

WATER CORROSION AND/OR ELECTRICAL SHORT CIRCUIT.

 For added protection, mount the fixture in areas outside walking paths, seating

areas, or in areas were unauthorized personnel might reach the fixture.

 Ambient operating temperature range for this fixture is 5° to 113°F. (-15° to 45°C)

Do not use the fixture under or above this temperature.

 Before mounting the fixture to any surface, make sure the installation area can

hold a minimum point load of 10 times the weight of the fixture.

 Fixture installation must always be secured with a secondary safety attachment,

such as an appropriate safety cable.

 Never stand directly below the device when mounting, removing or servicing.

11 FUZE PAR Z120 IP™ User Manual

www.elationlighting.com

CLAMP INSTALLATION

The fixture provides a integrated mounting dual bracket / yoke. When mounting this

fixture to truss be sure to secure an appropriately rated clamp to the mounting

bracket / yoke using a M10 screw fitted through the center hole. Be sure to attach

an appropriate Safety Cable (not included) to the fixture using the safety cable

rigging point integrated into the back of the fixture.

12 FUZE PAR Z120 IP™ User Manual

www.elationlighting.com

RIGGING

Overhead rigging requires extensive experience, including amongst others

calculating working load limits, installation material being used, and periodic safety

inspection of all installation material and the fixture. If you lack these qualifications,

do not attempt the installation yourself. Improper installation can result in bodily

injury. Fixture is fully operational in the specific mounting positions illustrated below.

SAFETY CABLE

ALWAYS USE A SAFETY CABLE WHENEVER INSTALLING THIS FIXTURE IN A SUSPENDED

ENVIRONMENT TO ENSURE THE FIXTURE WILL NOT DROP IF THE CLAMP FAILS.

13 FUZE PAR Z120 IP™ User Manual

POWER LINKING

Max number of FUZE WASH Z120 IP™ units power linked together:

6 units @120V | 12 units @240V

NOTE: USE CAUTION WHEN POWER LINKING OTHER FIXTURES TO FUZE PAR Z120 IP™!

POWER CONSUMPTION OF OTHER LIGHTING FIXTURES WILL VARY!

ALWAYS CHECK MAX AMP OUT RATING PRINTED ON THE REAR CONNECTION PANEL!

www.elationlighting.com

14 FUZE PAR Z120 IP™ User Manual

ZOOM

ELATION

Fuze Par

www.elationlighting.com

SYSTEM MENU

The fixture comes with an easy to navigate system menu. The control panel (see

image below) located on the front the fixture provides access to the main system

menu and is where all necessary system adjustments are made to the fixture. During

normal operation, pressing MODE button once will access the fixture’s main menu.

Once in the main menu you can navigate through the different functions and

access the sub-menus with the UP and DOWN buttons. Once you reach a field that

requires adjusting, press the ENTER button to activate that field and use the UP and

DOWN buttons to adjust the field. Pressing the ENTER button once more will confirm

your setting. You may exit the main menu at any time without making any

adjustments by pressing the MODE/ESC button.

INFORMATION DISPLAYED DURING INITIAL POWER ON

When the fixture is initially powered ON, the display shows the following information:

Update Wait...

15 FUZE PAR Z120 IP™ User Manual

Reset...

Vx.xx

Z120 IP

ELATION© FUZE PAR Z120 IP™

S Y S T E M M E N U

www.elationlighting.com

MENU OPTIONS / VALUES (Default Settings in BOLD) DESCRIPTION

Set ADDR

UserMode

Function

Info

001 ~ XXX

CH:04 RGBW, CH:04 HSI, CH:05 HSI+, CH:06 RGBW,
CH:07 sRGBWI, CH:07 RGBW, CH:08 RGBW, CH:09 RGBW,
CH:10 16Bit, CH:10 HSI, CH:12 sRGBWI, CH:13 RGBW

DimCurve

No DMX Hold / Blackout / Program Function If NO DMX Detected

ZOOM 000 - 255

AUTO RUN FQN: 01-99

01. STATIC
CL: R

02. CHANG
SP01 F00

03. FADE
SP01 F00

Macros 00-63 Select Color Macro

LCD. Set

DFSET

TEMP

Current XXXX (Hours) Fixture Run Time From Power ON

Total Time XXXX (Hours) Fixture Total Run Time

Last Clear XXXX (Hours) Clear Fixture Last Run Time

Timer PIN

Clear Last ON / OFF Reset Fixture Last Run Time

Clear Total

TempInfo

ModelInf

Software Version

Standard, Stage, TV,
Architectur, Theatre

R/G/B/RG/GB/RB/RGB/BLAC
F 00

SP01-99 F00-99 Set Color Change Program Macro

SP01-99 F00-99 Set Color Fade Program Macro

Backligh
05-60

Key Lock
OFF / ON

DispFlash
ON / OFF

OFF / ON

Fahren / Celsius

PIN= 050

ON / OFF

XXX F° / C°
Fuze Par

Z120 IP

1U ≥V1.03

2U ≥V1.03

DMX Address Setting

Set DMX Channel

Set Dimmer Curve Mode

Set the number of times each
internal macro will repeat before
moving to the next macro.

Set Static Color Program Macro

LCD Backlight Shut Off Time (mins)

Control Front Panel Buttons Key Lock

Display flashes when NO DMX

Reset Fixture Back Factory Defaults

Temperature 'G9D385DG55>NN

Enter PIN to Access Clear Last. Menu

Clear Total Time Password = 060

Temperature in Fixture Head

Display Fixture Model Name

Software Versions

16 FUZE PAR Z120 IP™ User Manual

ELATION© FUZE PAR Z120 IP™

S Y S T E M M E N U

MENU OPTIONS / VALUES (Default Settings in BOLD) DESCRIPTION

www.elationlighting.com

ZoomRset

Slave

Manual

Reset. M

Slave

ManCtrl
ZOOM

ManCtrl
Dimmer

ManCtrl
Red

ManCtrl
Green

ManCtrl
Blue

ManCtrl
White

ManCtrl
Strobe

000 - 255

000 - 255

000 - 255

000 - 255

000 - 255

000 - 255

000 - 255

Reset of Zoom Motor

Set Slave Mode

Manual Control

17 FUZE PAR Z120 IP™ User Manual

Function - DimCurve

Select desired DIMMER MODE (Standard, Stage, TV, Architectural, Theatre).

www.elationlighting.com

18 FUZE PAR Z120 IP™ User Manual

ELATION© FUZE PAR Z120 IP™

DMX Channel Values / Functions Version (13 DMX Channels)

Supports Software Versions: ≥ 1.03

Random Strobe Effect
SLOW to FAST

www.elationlighting.com

DMX CHANNEL FUNCTIONS AND VALUES

Features are subject to change without any prior written notice.

MODE / CHANNEL

CH:04
RGBW

CH:04

1 1 2 1 1 1 1 2 1

2

2 2 3 2 2 2 3 3 2

4

3 3 4 3 3 3 5 4 3

6

4 4 5 4 4 4 7 5 4

8

1 5 5 1 1 6

1 1 2

2 2 3

3 3 6 4 6

HSI

CH:05

HSI

CH:06
RGBW

CH:07

sRGBWI

CH:07
RGBW

CH:08
RGBW

CH:09
RGBW

CH:10

16Bit

CH:10

HSI

CH:12
sRGBI

CH:13
RGBW

VALUE FUNCTION

0-255 0 to 100%

0-255 RED FINE Adjustment

0-255 0 to 100%

0-255 GREEN FINE Adjustment

0-255 0 to 100%

0-255 BLUE FINE Adjustment

0-255 0 to 100%

0-255 WHITE FINE Adjustment

0-31 LED OFF

32-63 LED ON

64-95 Strobe Effect SLOW to FAST

96-127 LED ON

128-159 Pulse Effect in Sequences

160-223

224-255 LED ON

0-255 0-100%

0-255 0-100%

0-255 0-100%

RED

RED FINE

GREEN

GREEN FINE

BLUE

BLUE FINE

WHITE

WHITE FINE

SHUTTER / STROBE

HUE

SATURATION

INTENSITY

19 FUZE PAR Z120 IP™ User Manual

ELATION© FUZE PAR Z120 IP™

www.elationlighting.com

DMX Channel Values / Functions Version (13 DMX Channels)

Supports Software Versions: ≥ 1.03

Features are subject to change without any prior written notice.

MODE / CHANNEL

CH:04
RGBW

CH:04

HSI

5 7 5

CH:05

HSI

CH:06
RGBW

CH:07

sRGBWI

CH:07

RGBW

CH:08
RGBW

CH:09
RGBW

CH:10

16Bit

CH:10

HSI

CH:12
sRGBI

CH:13
RGBW

VALUE FUNCTION

COLOR PRESETS

0 OFF

1-4 COLOR PRESET 01

5-8 COLOR PRESET 02

9-12 COLOR PRESET 03

13-16 COLOR PRESET 04

17-20 COLOR PRESET 05

21-24 COLOR PRESET 06

25-28 COLOR PRESET 07

29-32 COLOR PRESET 08

33-36 COLOR PRESET 09

37-40 COLOR PRESET 10

41-44 COLOR PRESET 11

45-48 COLOR PRESET 12

49-52 COLOR PRESET 13

53-56 COLOR PRESET 14

57-60 COLOR PRESET 15

61-64 COLOR PRESET 16

65-68 COLOR PRESET 17

69-72 COLOR PRESET 18

73-76 COLOR PRESET 19

77-80 COLOR PRESET 20

81-84 COLOR PRESET 21

85-88 COLOR PRESET 22

89-92 COLOR PRESET 23

93-96 COLOR PRESET 24

97-100 COLOR PRESET 25

101-104 COLOR PRESET 26

105-108 COLOR PRESET 27

109-112 COLOR PRESET 28

113-116 COLOR PRESET 29

117-120 COLOR PRESET 30

121-124 COLOR PRESET 31

125-128 COLOR PRESET 32

20 FUZE PAR Z120 IP™ User Manual

ELATION© FUZE PAR Z120 IP™

DMX Channel Values / Functions Version (13 DMX Channels)

Supports Software Versions: ≥ 1.03

Features are subject to change without any prior written notice.

COLOR PRESETS

www.elationlighting.com

MODE / CHANNEL

CH:04
RGBW

CH:04

5 7 5

HSI

CH:05

HSI

CH:06
RGBW

CH:07

sRGBWI

CH:07

RGBW

CH:08
RGBW

CH:09
RGBW

CH:10

16Bit

CH:10

HSI

CH:12
sRGBI

CH:13
RGBW

VALUE FUNCTION

[continued]

129-132 COLOR PRESET 33

133-136 COLOR PRESET 34

137-140 COLOR PRESET 35

141-144 COLOR PRESET 36

145-148 COLOR PRESET 37

149-152 COLOR PRESET 38

153-156 COLOR PRESET 39

157-160 COLOR PRESET 40

161-164 COLOR PRESET 41

165-168 COLOR PRESET 42

169-172 COLOR PRESET 43

173-176 COLOR PRESET 44

177-180 COLOR PRESET 45

181-184 COLOR PRESET 46

185-188 COLOR PRESET 47

189-192 COLOR PRESET 48

193-196 COLOR PRESET 49

197-200 COLOR PRESET 50

201-204 COLOR PRESET 51

205-208 COLOR PRESET 52

209-212 COLOR PRESET 53

213-216 COLOR PRESET 54

217-220 COLOR PRESET 55

221-224 COLOR PRESET 56

225-228 COLOR PRESET 57

229-232 COLOR PRESET 58

233-236 COLOR PRESET 59

237-240 COLOR PRESET 60

241-244 COLOR PRESET 61

245-248 COLOR PRESET 62

249-252 COLOR PRESET 63

253-255 COLOR PRESET 64

21 FUZE PAR Z120 IP™ User Manual

ELATION© FUZE PAR Z120 IP™

DMX Channel Values / Functions Version (13 DMX Channels)

Features are subject to change without any prior written notice.

www.elationlighting.com

Supports Software Versions: ≥ 1.03

MODE / CHANNEL

CH:04
RGBW

CH:04

5 5 6 6 7

6 7 7 8

4 4 6 7 7 8 8 9 6 8 9

10

7 9 10

8 10 11

9 11 12

5 9 10 12 13

HSI

CH:05

HSI

CH:06
RGBW

CH:07

sRGBWI

CH:07
RGBW

CH:08
RGBW

CH:09
RGBW

CH:10

16Bit

CH:10

HSI

CH:12
sRGBI

CH:13
RGBW

VALUE FUNCTION

0-255 Dimmer 0 to 100%

0-255 Dimmer FINE Adjustment

0-255

0-255 ZOOM FINE Adjustment

1-20 COLOR MACRO 01

21-40 COLOR MACRO 02

41-60 COLOR MACRO 03

61-80 COLOR MACRO 04

81-100 COLOR MACRO 05

101-120 COLOR MACRO 06

121-140 COLOR MACRO 07

141-160 COLOR MACRO 08

161-180 COLOR MACRO 09

181-200 COLOR MACRO 10

201-230 COLOR MACRO 11

231-240 COLOR MACRO 12

241-250 COLOR MACRO 13

251-255 GRADIENT COLOR MACRO

0-125

126-130 STOP

131-255

0-255 0-100%

0-20 STANDARD

21-40 STAGE

41-60 TV

61-80 ARCHITECTURAL

81-100 THEATRE

101-255 Default to Unit Setting

DIMMER INTENSITY

DIMMER INTENSITY FINE

ZOOM

ZOOM 0% (5 Degrees)
to 100% (50 Degrees)

ZOOM FINE

PROGRAM MACROS

0 NO FUNCTION

PROGRAM MACRO SPEED

Counter-Clockwise
Movement FAST to SLOW

Clockwise Movement
SLOW to FAST

PROGRAM MACRO FADE

DIMMING CURVE MODES

22 FUZE PAR Z120 IP™ User Manual

www.elationlighting.com

CLEANING AND MAINTENANCE

CAUTION

Disconnect power before cleaning or maintenance.

CLEANING

Frequent cleaning is recommended to insure proper function, optimized light output,

and an extended life. The frequency of cleaning depends on the environment in

which the fixture operates: damp, smoky or particularly dirty environments can

cause greater accumulation of dirt on the fixture’s optics.

 Clean the external lens surface at least every 20 days with a soft cloth to avoid

dirt/debris accumulation.

 Never use alcohol, solvents, or ammonia based cleaners.

MAINTENANCE

Regular inspections are recommended to insure proper function and extended life.

There are no user serviceable parts inside this fixture, please refer all other service

issues to an authorized Elation service technician. Should you need any spare parts,

please order genuine parts from your local Elation dealer.

Please refer to the following points during routine inspections:

 A detailed electric check by an approved electrical engineer every three months,

to make sure the circuit contacts are in good condition and prevent overheating.

 Be sure all screws and fasteners are securely tightened at all times. Lose screws may

fall out during normal operation resulting in damage or injury as larger parts could fall.

 Check for any deformations on the housing, color lenses, rigging hardware and

rigging points (ceiling, suspension, trussing). Deformations in the housing could

allow for dust to enter into the fixture. Damaged rigging points or unsecured

rigging could cause the fixture to fall and seriously injure a person(s).

 Electric power supply cables must not show any damage, material fatigue or

sediments. Never remove the ground prong from the power cable.

23 FUZE PAR Z120 IP™ User Manual

www.elationlighting.com

TECHNICAL SPECIFICATIONS

SOURCE

120W RGBW COB LEDs
100,000 Hour Average Lamp Life*

*May vary depending on several factors including but not limited to:
Environmental Conditions, Power/Voltage, Usage Patterns (On-Off Cycling), Control, and Dimming.

COLOR

RGBW

EFFECTS

RGBW Color Mixing
7° - 55° Beam Zoom Range
Electronic Strobe, Dimming and Variable Dimming Curves
64 Color Presets and 14 Unique Color Macros

CONTROL / CONNECTIONS

12 DMX Channel Modes (13 Total Channels)
4 Touch Button Control Panel and LCD Menu Display
RDM (Remote Device Management)
IP rated 5pin DMX and powerCON TRUE1 In/Out

SIZE / WEIGHT

Length: 11.69" (283.7mm)
Width: 14.05" (356.8mm)
Vertical Height: 14.14" (359.2mm)
Weight: 19 lbs. (8.6 kg)

ELECTRICAL / THERMAL

AC 100-240V - 50/60Hz
158W Max Power Consumption
5F to 113°F (-15°C to 45°C)

APPROVALS / RATINGS

CE | IP65

Please Note: Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice.

24 FUZE PAR Z120 IP™ User Manual

PHOTOMETRIC DATA

3 m

9.8 ft

4 m

13.1 ft

5 m

16.4 ft

7° Beam

lux

fc

lux

fc

lux

fc

1,990

185

1,132

105

662

61

GREEN LEDs

3,534

328

2,005

186

1,219

113

BLUE LEDs

702

65

387

36

236

22

WHITE LEDs

5,789

538

342

32

2,089

194

FULL ON

9,112

847

5,183

482

3,352

311

3 m

9.8 ft

4 m

13.1 ft

5 m

16.4 ft

57° Field

lux

fc

lux

fc

lux

fc

82 8 50 5 32

3

GREEN LEDs

139

13

65 6 32

3

BLUE LEDs

27 3 13 1 6

1

WHITE LEDs

245

23

120

11

59

5

FULL ON

428

40

224

21

129

12

MIN ZOOM - 7° Beam Diameter

www.elationlighting.com

Diameter

14° Field

Diameter

RED LEDs

55° Beam

Diameter

Diameter

RED LEDs

0.3 1.0

0.98 3.2

MAX ZOOM - 55° Beam Diameter

3.12 10.2

3.16 10.4

0.39 1.3

1.28 4.2

4.16 13.6

4.2 13.8

0.47 1.5

1.58 5.2

5.2 17.1

5.24 17.2

25 FUZE PAR Z120 IP™ User Manual

DIMENSIONAL DRAWINGS

www.elationlighting.com

Please Note: Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice.

26 FUZE PAR Z120 IP™ User Manual

www.elationlighting.com

OPTIONAL ACCESSORIES

ORDER CODE ITEM

NARROW CLAMP PRO 2” Wrap Around Clamp

NEU088 3 ft. (1m) PowerCON TRUE1 Power Link Cable

Additional Cable Lengths Available

27 FUZE PAR Z120 IP™ User Manual