Elation Event Cylinder RF User Instructions

Event Cylinder RF

Event Cylinder RF General Information

Unpacking: Thank you for purchasing the Event Cylinder RF by Ela-

tion Professionals®. Every Event Cylinder RF has been thoroughly
tested and has been shipped in perfect operating condition. Carefully
check the shipping carton for damage that may have occurred during
shipping. If the carton appears to be damaged, carefully inspect your
xture for any damage and be sure all equipment necessary to oper­ate the unit has arrived intact. In the event damage has been found
or parts are missing, please contact our toll free customer support
number for further instructions. Please do not return this unit to your

dealer without contacting customer support rst.

Introduction: The Event Cylinder RF is an battery powered RGB LED

cylinder. The fixture five operating modes; show mode, sound active

mode, fade mode, manual mode, & static color mode.

Customer Support: Elation Professionals® provides a toll free cus-

tomer support line, to provide help and to answer any question should

you encounter problems during your set up or initial operation. You
may also visit us on the web at www.elationlighting.com for any com­ments or suggestions. Service Hours are Monday through Friday 8:00

a.m. to 4:30 p.m. Pacic Standard Time.

Voice: [phone]

Fax: [phone]

E-mail: [e-mail]
To purchase parts online visit http://parts.elationlighting.com

5/12

Warning! To prevent or reduce the risk of electrical shock or re, do

not expose this unit to rain or moisture.

Warning! This may cause severe eye damage. Avoid looking directly

into the light source at all times!

User Instructions

©Elation Professionals® - www.elationlighting.com - Instruction Manual Page 2

Event Cylinder RF General Instructions

Event Cylinder RF Safety Precautions

To optimize the performance of this product, please read these
operating instructions carefully to familiarize yourself with the basic
operations of this unit. These instructions contain important safety
information regarding the use and maintenance of this unit. Please
keep this manual with the unit, for future reference.

Event Cylinder RF Features

• 5 Operating Modes - Show Mode, Sound Active Mode, Fade

Mode, Manual Mode, & Static Color Mode

• Digital Display for Function Setting

• 9 Preset Colors + White

• TRI Color Mixing

• Wireless RF Control

Event Cylinder RF Warranty Registration

The Event Cylinder RF carries a 2 year (730 days) limited warranty.
Please fill out the enclosed warranty card to validate your purchase
and warranty. You may also register your product online at www.ela­tionlighting.com. All returned service items whether under warranty or
not, must be freight pre-paid and accompany a return authorization
(R.A.) number. If the unit is under warranty you must provide a copy
of your proof of purchase invoice. Please contact Elation® customer

support for a R.A. number.

Event Cylinder RF Handling Precautions

Caution! There are no user serviceable parts inside this unit. Do not

attempt any repairs yourself, doing so will void your manufactures war-

ranty. In the unlikely event your unit may require service please contact

Elation Professionals®.

During operation the housing may become hot. Avoid touching the
unit with bare hands while in use.

Elation Professionals® will not accept any liability for any resulting dam-
ages caused by the non-observance of this manual or any unauthor-

ized modication to this unit.

For Your Own Personal Safety, Please Read and Understand This

Manual Completely Before You Attempt To Install Or Operate

This Unit!

• To reduce the risk of electrical shock or re, do not expose this unit

rain or moisture

• Do not spill water or other liquids into or on to your unit.

• Do not attempt to operate this unit if the power supply has been

frayed or broken.

• Do not attempt to remove or break off the ground prong from

the electrical cord. This prong is used to reduce the risk of electrical

shock and re in case of an internal short.

• Disconnect from main power before making any type of connection.

• Do not remove the cover under any conditions. There are no user

serviceable parts inside.

• Never operate this unit when it’s cover is removed.

• Always be sure to mount this unit in an area that will allow proper
ventilation. Allow about 6” (15cm) between this device and a wall.

• Do not attempt to operate this unit, if it becomes damaged.

• This unit is intended for indoor use only, use of this product out-

doors voids all warranties.

• Always mount this unit in safe and stable matter.

• Power-supply cords should be routed so that they are not likely to

be walked on or pinched by items placed upon or against them,
paying particular attention to cords at plugs, convenience recep-

tacles, and the point where they exit from the appliance.

• Cleaning -The fixture should be cleaned only as recommended by

the manufacturer. See page 13 for cleaning details.

• Heat -This fixture should be situated away from heat sources such

as radiators, heat registers, stoves, or other appliances (including
amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel when:
A. Objects have fallen, or liquid has been spilled into the appliance.
B. The appliance has been exposed to rain or water.
C. The appliance does not appear to operate normally or exhibits a

marked change in performance.

©Elation Professionals® - www.elationlighting.com - Instruction Manual Page 4©Elation Professionals® - www.elationlighting.com - Instruction Manual Page 3

Event Cylinder RF System Menu Event Cylinder RF System Menu

ShoU - In this mode you can choose 1 of 10 shows to run.

Shows can run with or without sound activity.

1. Press the MENU button until “ShoU” is displayed, press
ENTER.

2. “Sh X” will now be displayed, “X” representing a number
between 0-10. Programs 1-10 are factory programs, while “Sh
0” is random mode. Press the UP or DOWN buttons to nd your

desired show.

4. When you have found your desired show press ENTER, then
press and hold the MENU button for at least 3 seconds to acti­vate. After you have set your desired show, it can be changed at
any time using the UP or DOWN buttons.

Fade - This menu will activate the Fade mode.

1. Press the MENU button until “Fade” is displayed, press ENTER.

2. “SP X” will now be displayed, “X” representing a number
between 1-10. This is fade speed adjustment; 1 being the slow­est fade and 10 being the fastest. Press the UP or DOWN but­tons to adjust the fade speed to your desire.

3. When you have found your desired fade speed press ENTER,
then press and hold the MENU button for at least 3 seconds to

activate.

CoLr - This menu will color mode and let you select a color

to remain static.

1. Press the MENU button until “CoLr” is displayed, press ENTER.

2. “Co X” will now be displayed, “X” representing a number
between 1-10. Numbers 1-10 are the static colors to choose
from. Use the UP or DOWN buttons to scroll through the 10

colors.

©Elation Professionals® - www.elationlighting.com - Instruction Manual Page 6©Elation Professionals® - www.elationlighting.com - Instruction Manual Page 5