diagrams, images, and instructions herein are subject to change without notice. ELATION
PROFESSIONAL logo and identifying product names and numbers herein are trademarks
of ELATION PROFESSIONAL. Copyright protection claimed includes all forms and matters
of copyrightable materials and information now allowed by statutory or judicial law or
hereinafter granted. Product names used in this document may be trademarks or
registered trademarks of their respective companies and are hereby acknowledged. All
non-ELATION brands and product names are trademarks or registered trademarks of their
respective companies.
ELATION PROFESSIONAL and all affiliated companies hereby disclaim any and all
liabilities for property, equipment, building, and electrical damages, injuries to any persons,
and direct or indirect economic loss associated with the use or reliance of any information
contained within this document, and/or as a result of the improper, unsafe, insufficient and
negligent assembly, installation, rigging, and operation of this product.
Elation Professional USA | 6122 S. Eastern Ave. | Los Angeles, CA. 90040
323-582-3322 | 323-832-9142 fax
Elation Profess
+31 45 546 85 66 | +31 45 546 85 96 fax
ation Professional Mexico | AV Santa Ana 30 | Parque Industrial Lerma, Lerma, Mexico 52000
El
+52 (728) 282-7070
ional B.V. | Junostraat 2 | 6468 EW Kerkrade, The Netherlands
DOCUMENT VERSION
Due to additional product features and/or enhancements,
an updated version of this document may be available
online. Please scan the QR Code with your mobile device for
the latest revis
ion/update of this manual, before
installation and/or programming.
2
CONTENTS
General Information
4
Limited Warranty (USA Only)
5
Safety Guidelines
6
Power Over Ethernet (POE) Explained
7
Device Overview
8
Installation Guidelines
9
System Menu
10
Setting DMX Ports
13
Specifications
14
Optional Accessories
15
3
GEN ERAL I NF ORMATI ON
INTRODUCTION
Please read and understand the instructions in this manual carefully and thoroughly before
attempting
information.
UNPACKING
Every device has been thoroughly tested and has been shipped in perfect operating
condition. Carefully check the shipping carton for damage that may have occurred during
shipping. If the carton is damaged, carefully inspect the device for damage, and be sure all
accessories necessary to install and operate the device have arrived intact. In the event
damage has been found or parts are missing, please contact our customer support team
for further instructions. Please do not return this device to your dealer without first
contacting customer support. Please do not discard the shipping carton in the trash.
Please recycle whenever possible.
BOX CONTENTS
Mini Omega Bracket (for truss/clamp mounting)
to operate this device. These instructions contain important safety and use
CUSTOMER SUPPORT
Contact ELATION Service for any product related service and support needs.
ELATION SERVICE USA - Monday - Friday 8:00am to 4:30pm PST
323-582-3322 | Fax 323-832-9142 | support@elationlighting.com
ELATION SERVICE EUROPE - Monday - Friday 08:30 to 17:00 CET
+31 45 546 85 63 | Fax +31 45 546 85 96 | support@elationlighting.eu
IMPORTANT NOTICE!
THERE ARE NO USER SERVICEABLE PARTS INSIDE THIS UNIT. DO NOT ATT E MP T A N Y R EPA IR S
YOURSELF; DOING SO WILL VOID YOUR MANUFACTURES WARRANTY. DAMAGES RESULTING
FROM MODIFICATIONS TO THIS FIXTURE AND/OR THE DISREGARD OF SAFETY INSTRUCTIONS
AND GUIDELINES IN THIS MANUAL VOID THE MANUFACTURES WARRANTY AND ARE NOT SUBJECT
TO ANY WARRANTY CLAIMS AND/OR REPAIRS.
4
LIMITED WARRANTY (USA ONLY)
A. Elation Professional hereby warrants, to the original purchaser, Elation Professional products to be free of
manufacturing defects in material and workmanship for a period of two years (730 days), and Elation
Professional product rechargeable batteries to be free of manufacturing defects in material and workmanship for
a period of six months (180 days), from the original date of purchase. This warranty excludes discharge lamp
and all product accessories. This warranty shall be valid only if the product is purchased within the United
States of America, including possessions and territories. It is the owner’s responsibility to establish the date and
place of purchase by acceptable evidence, at the time service is sought. B. For warranty service, send the
product only to the Elation Professional factory. All shipping charges must be pre-paid. If the requested repairs
or service (including parts replacement) are within the terms of this warranty, Elation Professional will pay return
shipping charges only to a designated point within the United States. If any product is sent, it must be shipped
in its original package and packaging material. No accessories should be shipped with the product. If any
accessories are shipped with the product, Elation Professional shall have no liability what so ever for loss and/or
or damage to any such accessories, nor for the safe return thereof. C. This warranty is void if the product serial
number and/or labels are altered or removed; if the product is modified in any manner which Elation Professional
concludes, after inspection, affects the reliability of the product; if the product has been repaired or serviced by
anyone other than the Elation Professional factory unless prior written authorization was issued to purchaser b
Elation Professional; if the product is damaged because not properly maintained as set forth in the product
instructions, guidelines and/or user manual. D. This is not a service contract, and this warranty does not include
any maintenance, cleaning or periodic check-up. During the periods as specified above, Elation Professional will
replace defective parts at its expense, and will absorb all expenses for warranty service and repair labor by
reason of defects in material or workmanship. The sole responsibility of Elation Professional under this warranty
shall be limited to the repair of the product, or replacement thereof, including parts, at the sole discretion of
Elation Professional. All products covered by this warranty were manufactured after January 1, 1990, and bare
identifying marks to that effect. E. Elation Professional reserves the right to make changes in design and/or
performance improvements upon its products without any obligation to include these changes in any product
theretofore manufactured. F. No warranty, whether expressed or implied, is given or made with respect to any
accessory supplied with the products described above. Except to the extent prohibited by applicable law, all
implied warranties made by Elation Professional in connection with this product, including warranties of
merchantability or fitness, are limited in duration to the warranty periods set forth above. And no warranties,
whether expressed or implied, including warranties of merchantability or fitness, shall apply to this product after
said periods have expired. The consumer’s and/or dealer’s sole remedy shall be such repair or replacement as is
expressly provided above; and under no circumstances shall Elation Professional be liable for any loss and/or
damage, direct and/or consequential, arising out of the use of, and/or the inability to use, this product. G. Thi
warranty is the only written warranty applicable to Elation Professional products and supersedes all prior
warranties and written descriptions of warranty terms and conditions heretofore published.
s
y
s
s
WARRANTY RETURNS
All returned service items whether under warranty or not, must be freight pre-paid and accompany a return
authorization (R.A.) number. The R.A. number must be clearly written on the outside of the return package. A
brief description of the problem as well as the R.A. number must also be written down on a piece of paper and
included in the shipping container. If the unit is under warranty, you must provide a copy of your proof of
purchase invoice. Items returned without a R.A. number clearly marked on the outside of the package will be
refused and returned at customer’s expense. You may obtain a R.A. number by contacting customer support.
ONLY Use the original packaging and materials to transport the fixture in for service.
5
SAFETY GUIDELINES
THERE ARE NO USER SERVICEABLE PARTS INSIDE THIS UNIT.
DO NOT ATTEMPT ANY REPAIRS YOURSELF; DOING SO WILL VOID
YOUR MANUFACTURES WARRANTY. DAMAGES RESULT IN G FR OM
MODIFICATIONS TO THIS DEVICE AND/OR THE DISREGARD OF
SAFETY INSTRUCTIONS AND GUIDELINES IN THIS MANUAL VOID
THE MANUFACTURES WARRANTY AND ARE NOT SUBJECT TO ANY
WARRANTY CLAIMS AND/OR REPAIRS.
DO NOT PLUG DEVICE INTO A DIMMER PACK!
NEVER OPEN THIS DEVICE WHILE IN USE!
DO NOT EXPOSE DEVICE TO HEAT OR FIRE!
DO NOT EXPOSE DEVICE TO HIGH HUMIDITY!
AMBIENT TEMPERATURES: MAX 45°C/113°F | MIN 2°C/35°F
UNPLUG POWER BEFORE SERVICING DEVICE!
DO NOT EXPOSE DEVICE TO FLAMMABLE MATERIALS!
DO NOT EXPOSE DEVICE TO EXTREME VIBRATIONS!
KEEP FLAMMABLE MATERIALS AWAY FROM FIXTURE!
INDOOR / DRY LOCATIONS USE ONLY!
DO NOT EXPOSE DEVICE TO RAIN AND MOISTURE!
To guarantee a smooth operation, it is important to follow all instructions and guidelines in
this manual. Elation Professional is not responsible for injury and/or damages resulting from
the misuse of this device due to the disregard of the information printed in this manual.
Only qualified and/or certified personnel should perform installation of this device and only
the original rigging parts included with this device should be used for installation. Any
modifications to the fixture and/or the included mounting hardware will void the original
manufactures warranty and increase the risk of damage and/or personal injury.
DO NOT shake device, avoid brute force when installing and/or operating.
DO NOT operate device if the power cord has become frayed, crimped, damaged and/or if
any of the power cord connectors are damaged and do not insert into the device securely
with ease. NEVER force a power cord connector into the device. If the power cord or any of
its connectors are damaged, replace it immediately with a new one of similar power rating.
DO NOT block any air ventilation slots. All fan and air inlets must remain clean and never
blocked. Always disconnect device from main power source before performing any type of
service and/or cleaning procedure. Only handle the power cord by the plug end, never pull
out the plug by tugging the wire portion of the cord.
Use the original packaging and materials to transport the device in for service.
6
POWER OVER ETHERNET (POE) EXPLAINED
Power over Ethernet (POE) is a technology that lets network cables carry electrical power.
Since electrical currents flow in a loop, two conductors are required to deliver power over a
cable. POE treats each pair as a single conductor, and can use either the two data pairs or
the two spare pairs to carry electrical current.
Network cables, such as Cat 5e and Cat 6, comprise eight wires arranged as four twisted
pairs. In 10 and 100BASE-T Ethernet, two of these pairs are used for sending information,
and these are known as the data pairs. The other two pairs are unused and are referred to
as the spare pairs (Gigabit Ethernet uses all four pairs).
POE is injected onto the cable at a voltage between 44 and 57 volts DC, and typically 48
volts is used. This relatively high voltage allows efficient power transfer along the cable,
while still being low enough to be regarded as safe.
7
DEVICE OVERVIEW
1.Power LED Indicator
2.Network Link LED Indicator
3.Network Activity LED Indicator
4.OLED Control Display
5.MENU Button
6.UP/DOWN Buttons
7.ENTER Button
8.RJ45 Ethernet Input
9.5pin DMX1 and DMX2 Connections
10.Power Switch (On/Off)
8
INSTALLATION GUIDELINES
FLAMMABLE MATERIAL WARNING
Keep device at least 5.0 feet (1.5m) away from any
flammable materials, decorations, pyrotechnics, etc.
ELECTRICAL CONNECTIONS
A qualified electrician should be used for all
electrical connections and/or installations.
Attach To Truss With
Mini Omega Bracket
and Clamp
DO NOT INSTALL THE DEVICE IF YOU ARE NOT QUALIFIED TO DO SO!
DO NOT CONNECT DEVICE TO A CIRCULAR NETWORK! DOING SO WILL
ADVERSELY IMPACT THE PERFORMANCE OF THE ENTIRE NETWORK SYSTEM!
Device MUST be installed following all local, national, and country commercial electrical
and construction codes and regulations.
Ambient operating temperature range for this device is 35° to 113°F.(2° to 45°C)
DO NOT use the device under or above this temperature range.
DO NOT install the device in areas were unauthorized personnel might reach the device.
Device can be placed on the flat surface or attached to truss using included mini omega
bracket and a properly rated clamp. (Clamp not included) (See below)
INSTALLATION LOCATION ON TRUSS MUST BE CLEAR OF ANY MOVING HEAD FIXTURES!
9
SYSTEM MENU
The OLED control panel display located on the front of the device provides access to the
main system menu where all necessary system adjustments are made to the device. During
normal operation, pressing MENU button once will access the main menu. Once in the
main menu you can navigate through the different functions and access the sub-menus
with the UP and DOWN buttons. Once you reach a field that requires adjusting, press the
ENTER button to activate that field and use the UP and DOWN buttons to adjust the field.
Pressing the ENTER button once more will confirm your setting. You may exit the main
menu at any time without making any adjustments by pressing the MENU button. The
OLED display will revert back to the last startup view after a few seconds of no activity.
10
STARTUP VIEWS
eNode!2!POE!
5E:D2:78:54:52:12!
002.010.010.002!
001!
Port%Status%
1%
2%
0"X"H"
001"
0"X"H"
001"
There are 5 different status screens (see images below) visable when device is connected
to a powered POE source. Select/switch screens by pressing the UP or DOWN buttons.
1. Device Name - This displays the current name (16 characters max).
SYSTEM MENU UPDATE WITH SOFTWARE UPDATE VERSION ≥1.3
The menu item below has been added with this software update.
2. MAC Address - This displays the current MAC Address.
Press and hold the ENTER button to access the MAC Address menu to make changes.
3. IP Address - This displays the current IP Address.
4. Device ID - This displays the current Device ID.
5. Port Status - This displays the status of each port 1 and 2.
O = DMX Output
I = DMX Input
✔
= Network Active
✕
= Network Inactive
H = Hold
B = Blackout
-= Not Allowed
11
ELATION eNode2 POE S Y S T E M M E N U
Features subject to change without written notice.
Supports Software Version: ≥ V1.1
MAIN MENU
SUB MENU
OPTIONS / VALUES (Default Settings in BOLD)
DESCRIPTION
1.Rename
Device
Rename
eNODE 2 POE
Select 1-16 Characters to Rename Device
2.Set IP Address
IP Address
002.010.010.002
Set Device IP Address
Each IP Address MUST be unique
3.Set Netmask
Netmask
A. 255.000.000.000
Select Netmask Address
B. 255.255.000.000
C. 255.255.255.000
4.Set DMX Port
DMX Port
1.DMX Port1
2.DMX Port2
1.Port Status
Output, Input, Disabled
Select DMX Port Status
2.Port Mode
Single, HTP, LTP,
Backup, RDM, zero
Select DMX Port Mode
RDM not supported in current software
version
3.Framertf/fs
040, 010, 015, 020,
025, 030, 035
Select DMX Frame Rate
Only available for PORT STATUS = OUTPUT
4.Net
001 - 128
Set Sub Net
5.Principal
001-256
Set Principal Universe
6.Secondary
009, 001-256
Set Secondary Universe
7.Resend
Disabled, 001-256
Enable Resending of data
8.DMX State
Hold, Null, Blackout
Set How Connected Devices React to a
Loss of DMX Signal
9.Display Mode
Dec/256, Hex/F.F
Select Binary or Hex Display Mode
5.Set ID NO.
Device ID
001, 000-255
Select Device ID
6.Set LED
Backlight
LED Backlight
1.ON
Backlight Stays ON Always
2.OFF
Backlight Auto Turns OFF After 30 Seconds
7.Set LED
Brightness
LED Brightness
004, 000-010
Set Display Brightness
8.Factory Setting
Factory Setting
1.NO
Return All Settings to Default
ALL SETTINGS RESET TO DEFAULT!
2.YES
9.Version
Version
V1.x
Displays Software Version
12
SETTING DMX PORTS
PORT STATUS
INPUT - Any of the (2) ports can be set as INPUT. When a port is set as INPUT, only the
principle universe is available and the PORT MODE can set to NORMAL or BACKUP.
OUTPUT - Any of the (2) ports can be set as OUTPUT. The PORT MODE can be set to
DISABLED - Disables selected Port and will not send or receive any data.
!All Port Mode options can be selected for a Disabled Port, however none will function.
PORT MODES
NORMAL [ONLY available when Port Status = INPUT]
Selected DMX Port will send any valid DMX data to the network (and internal use) using the
selected Art-Net Universe.
BACKUP [ONLY available when Port Status = INPUT]
Selected DMX Port will not send any data if the selected Art-Net Universe is present on the
network. If the selected universe becomes unavailable for several seconds and there is
valid DMX input data present, the device will send the DMX data until data from the
selected Art-Net Universe begins sending data again.
SINGLE [ONLY available when Port Status = OUTPUT]
Sets selected Port to send the DMX values of the selected Principle Art-NET Universe.
DMX output is enabled the first time it detects the DMX universe on the network or DMX data input.
HTP (Highest Ta k e s P re c ed e n c e ) [ONLY when Port Status = OUTPUT]
Selected Port merges data from the Principle and Secondary Universes and outputs the
one with the higher value.
!Can only be selected for DMX Ports with a Port Status = OUTPUT
!
Make sure RESEND option in System Menu is NOT set to Disabled or data will not
be sent to the network.
LTP (La te st Tak es Pre ced en ce) [ONLY when Port Status = OUTPUT]
Selected Port outputs the latest channel activity from the Principle and Secondary
Universes on a channel-by-channel basis.
!Can only be selected for DMX Ports with a Port Status = OUTPUT
!
Make sure RESEND option in System Menu is NOT set to Disabled or data will not
be sent to the network.
RDM (Remote Device Management) [ONLY when Port Status = OUTPUT]
ZERO [ONLY when Port Status = OUTPUT]
Selected DMX Port sends a DMX test signal with all channels at 0%.
13
SPECIFICATIONS
CONTROL / CONNECTIONS
2-Universe Support
DMX, RDM, Art-Net, and sACN Protocol Support
DMX Bilateral Conversion
sACN Auto-Detection
4-Button Control Panel
OLED System Menu Display
(3) LED Status Indicators
(1) Auto-Switching 10/100Mbps RJ45 EtherCON Input
(2) Multi-Configuration 5pin DMX Data Outputs
2.6W Max Power Consumption
35°F to 113°F (2°C to 45°C)
APPROVALS
CE
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
FCC RADIO FREQUENCY INTERFERENCE WARNINGS & INSTRUCTIONS
This product has been tested and found to comply with the limits as per Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation.
This device uses and can radiate radio frequency energy and, if not installed and used in accordance with the
included instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this device does cause harmful
interference to radio or television reception, which can be determined by turning the device off and on, the
user is encouraged to try to correct the interference by one or more of the following methods:
•!Reorient or relocate the device.
•!Increase the separation between the device and the receiver.
•!Connect the device to an electrical outlet on a circuit different from which the radio receiver is connected.
•!Consult the dealer or an experienced radio/TV technician for help.
14
DIMENSIONAL DRAWINGS
ORDER CODE
ITEM
NARROW CLAMP
Heavy Duty 2 inch Clamp
CAT6PRO5
5 ft. (1.5m) CAT6 ETHER-CON Cable
AC5PDMX5PRO
5 ft. (1.5m) 5pin PRO DMX Cable
Additional Cable Lengths Available
Specifications and improvements in the design of this unit and this manual subject to change without notice.
OPTIONAL ACCESSORIES
15
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.