Elation DESIGN PROMO 360 User Manual

DESIGN PROMO 360

USER MANUAL

For your own safety, please read this user manual carefully before installing the device.

Keep this device away from rain and moisture !

Unplug mains lead before opening the housing.

Every person involved with the installation, operation and maintenance of this device has to:

-be qualified

-follow carefully the instructions of this manual

INTRODUCTION:

Thank you for having chosen this professional advertisement lighting.
You will see you have acquired a powerful and versatile device.

Unpack the device. Inside the box you should find:

1. The fixture device

2. A power cable

3. An XLR connection cable

4. A safety cable and this manual

Please check carefully that there is no damage caused by transportation. Should there be any, consult your dealer
and don’t install this device.

Features:

·16 bit resolution

·Movement: 540°/630° optional

·For smooth and precise resolution

·Can rotate continuously

·While Channel 4 on DMX value 0-63 , channel 1,2,3 can do 16 bit high resolution movement

·While Channel 4 on DMX value 64-127, the base rotates continuously in clockwise direction

·While Channel 4 on DMX value 128-191, the base rotated continuously in counterclockwise direction

·While Channel 4 on DMX value 236-245 , reset after 8 seconds

SAFETY INSTRUCTIONS

Be careful with your operations.With a dangerous voltage you can
Suffer a dangerous electric shock when touching wires!

This device has left the factory in perfect condition. In order to maintain this condition and to ensure
a safe operation, it is absolutely necessary for the user to follow the safety instructions and warning
notes written in this user manual.

- １ - XM080-V1.0 NR

If the device has been exposed to temperature changes due to environmental changes, do not switch
it on immediately. The arising condensation could damage the device. Leave the device switched off
until it has reached room temperature.

If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by
the manufacturer or his service agent or a similar qualified person in order to avoid a hazard.

This device falls under protection-class I. Therefore it is essential that the device be earthed.
The electric connection must carry out by qualified person.
Make sure that the available voltage is not higher than stated at the end of this manual.
Make sure the power cord is never crimped or damaged by sharp edges. If this would be the case,
replacement of the cable must be done by an authorized dealer.

Always disconnect from the mains, when the device is not in use or before cleaning it. Only handle
the power cord by the plug. Never pull out the plug by tugging the power cord.
During initial start-up some smoke or smell may arise. This is a normal process and does not
necessarily mean that the device is defective, it should decrease gradually.

CAUTION!

Never touch the device during operation!

The housing may heat up

Please be aware that damages caused by manual modifications to the device are not subject to
warranty. Keep away from children and non-professionals.

GENERAL GUIDELINES

This device is a lighting effect for professional use on stages, in discotheques, theatres, etc.
This fixture is only allowed to be operated with the max alternating current which stated in the
technical specifications in the last page of this manual, the device was designed for indoor use only.
Lighting effects are not designed for permanent operation. Consistent operation breaks may ensure
that the device will serve you for a long time without defects. Do not shake the device.
Avoid brute force when installing or operating the device.

While choosing the installation-spot, please make sure that the device is not exposed to extreme heat,
moisture or dust. The minimum distance between light-output from the projector

Always fix the fixture with an appropriate safety cable if you use the clamp to hang up the fixture.
When fixing the device on a raised-from-the- ground support, be sure to use no less than screws and
nuts of M10 x 25 mm and insert them in the pre-arranged screw holes in the base of the fixture.
If you use the quick lock cam in hanging up the fixture, please make sure the 4 quick lock fasteners
turned in the quick lock holes correctly.

Operate the device only after having familiarized with its functions. Do not permit operation by
persons not qualified for operating the device. Most damages are the result of unprofessional

- ２ - XM080-V1.0 NR

operation.

Please use the original packaging if the device is to be transported.
For safety reasons, please be aware that all modifications on the device are forbidden.

If this device will be operated in any way different to the one described in this manual, the product
may suffer damages and the guarantee becomes void. Furthermore, any other operation may lead to
short-circuit, burns, electric shock, lamp explosion, crash, etc.

INSTALLATION INSTRUCTIONS

Mounting the device

Please consider the EN 60598-2-17 and the other respective national norms during the

installation. The installation must only be carried out by a qualified person.

The installation of the effect has to be built and constructed in a way that it can hold 10 times the
weight for 1 hour without any harming deformation.

The installation must always be secured with a secondary safety attachment, e.g. an appropriate
safety cable.
Never stand directly below the device when mounting, removing or servicing the fixture.

The operator has to make sure the safety relating and machine technical installations are approved by
an expert before taking the device into operation for the first time.
These installations have to be approved by a skilled person once a year.

Before taking into operation for the first time,

the installation has to be approved by an expert.

Cautions:

The effect should be installed outside areas where persons may reach it, walk by or be seated.

Overhead mounting requires extensive experience, including amongst others calculating
working load limits, installation material being used, and periodic safety inspection of all
installation material and the device. If you lack these qualifications, do not attempt the
installation yourself. Improper installation can result in bodily injury.

The electric connection must only be carried out by a qualified electrician.

Before mounting make sure that the installation area can hold a minimum point load of 10 times the

- ３ - XM080-V1.0 NR

device’s weight.
Connect the fixture to the mains with the power plug.

Installation method via clamp
Please refer to the picture below:

(1)Omega-holders
(2) Clamp
(3) Safety-rope
(4)Quick-lock fastener

Screw one clamp each via a M12 screw and nut onto the Omega holders.
Insert the quick-lock fasteners of the first Omega holder into the respective holes on the bottom of
the device. Tighten the quick-lock fasteners fully clockwise. Install the second Omega holder.
Pull the safety-rope through the holes on the bottom of the base and over the trussing system or a
safe fixation spot. Insert the end in the carabine and tighten the safety screw.

DMX-512 control connection

Connect the provided XLR cable to the female 3-pin XLR output of your controller and the other
side to the male 3-pin XLR input of the ad lighting. You can chain multiple ad lighting together
through serial linking. The cable needed should be two core,

connectors. Please refer to the diagram below.

DMX-512 connection with DMX terminator

screened cable with XLR input and output

- ４ - XM080-V1.0 NR