Elation Design 60 Tri, Design LED 60 TriStrip Owner's Manual
Rev. 3/04/2009 - visage
Design LED 60 TriStrip
Elation Professional™
6122 S. Eastern Ave.
Los Angeles, CA. 90040
www.elationlighting.com
Design LED 60 TriStrip™
©Elation Professional, Los Angeles Ca. 1 www.ElationLighting.com
Design LED 60 TriStrip™
©Elation Professional, Los Angeles Ca. 2 www.ElationLighting.com
TABLE OF CONTENS
1. General Information……………………………………………………………………… 3
a. Introduction………………………………………………………………………. 3
b. Unpacking………………………………………………………..…………..… 3
c. Customer Support…………………………………………….………………… 3
d. Warranty Registration……………………………………………………..…… 3
2. Safety Instructions………………………………………………………........…………. 5
3. Features……………………………………………………………………………………7
4. General Guidelines………………………………………………………………………. 8
5. Fixture Overview…………………………………………………………………………. 9
6. Mounting and Installation………………………………………………………….……. 11
7. Understanding DMX……………………………………………………………………... 14
a. DMX Linking……..………………………………………………………………. 14
b. DMX Cables…..…………………………………………………………………. 14
c. DMX Termination………………………………………………………………… 16
d. 3-Pin to 5-Pin Conversion………………………………………………………. 16
e. Understanding DMX Addressing.……………………………………………… 16
8. Display Menu….……………………………………………………..…………………… 18
9. DMX Operation……………………………………………………..………………….… 20
a. DMX Mode Selection……………………………………………………………. 20
10. DMX Channel Traits………………………………………………………………………22
11. Cleaning and Maintenance………………………………………………………………33
12. Warranty…………………………………………………………………………………... 34
13. Photometric Data………………………………………………………………………… 36
14. Dimensional Drawings………………………………………………….……………….. 37
15. Lens Change………………………………..……………………………………………. 38
16. Circuit Schematic………...………………………………………………………………. 39
17. Technical Specifications…………………………………………...………….………… 40
Design LED 60 TriStrip™
©Elation Professional, Los Angeles Ca. 3 www.ElationLighting.com
1. GENERAL INFORMATION
INTRODUCTION: Congratulations, you have just purchased one of the most innovative and
reliable LED fixtures on the market today! The Design LED 60 TriStrip™ has been designed
to perform reliably for years when the guidelines in this booklet are followed. Please read
and understand the instructions in this manual carefully and thoroughly before attempting to
operate this unit. These instructions contain important information regarding safety during
use and maintenance.
UNPACKING: Thank you for purchasing the Design LED 60 TriStrip™ by Elation
Professional®. Every Design LED 60 TriStrip™ has been thoroughly tested and has been
shipped in perfect operating condition. Carefully check the shipping carton for damage that
may have occurred during shipping. If the carton appears to be damaged, carefully inspect
your fixture for damage and be sure all accessories necessary to operate the fixture have
arrived intact. In the event damage has been found or parts are missing, please contact our
customer support team for further instructions. Please do not return this unit to your dealer
without first contacting customer support at the number listed below.
Inside the box you should find: the fixture, a DMX XLR cable, an IEC power cable, an IEC
“jumper” power cable, a safety cable, and this manual. Please contact customer support at
the number listed below if any of the above items are missing.
CUSTOMER SUPPORT: Elation Professional® provides a customer support line, to provide
set up help and to answer any question should you encounter problems during your set up
or initial operation. You may also visit us on the web at www.elationlighting.com for any
comments or suggestions. For service related issue please contact Elation Professional®.
Service Hours are Monday through Friday 9:00 a.m. to 5:00 p.m. Pacific Standard Time.
Voice: (323) 582-3322
Fax: (323) 832-9142
E-mail: support@elationlighting.com
Forum: www.ElationLighting.com/forum
Warning! To prevent or reduce the risk of electrical shock or fire, do not expose this unit to
Design LED 60 TriStrip™
©Elation Professional, Los Angeles Ca. 4 www.ElationLighting.com
rain or moisture.
Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs
yourself. Doing so will void your manufactures warranty.
Please do not discard the shipping carton in the trash. Please recycle whenever possible.
WARRANTY REGISTRATION: The Design LED 60 TriStrip™ comes with a two year (730
days) limited warranty. Please fill out the enclosed warranty card to validate your purchase.
All returned service items whether under warranty or not, must be freight pre-paid and
accompany a return authorization (R.A.) number. The R.A. number must be clearly written
on the outside of the return package. A brief description of the problem as well as the R.A.
number must also be written down on a piece of paper and included in the shipping
container. If the unit is under warranty, you must provide a copy of your proof of purchase
invoice. Items returned without a R.A. number clearly marked on the outside of the package
will be refused and returned at customer’s expense. You may obtain a R.A. number by
contacting customer support at (323) 582-3322.
Design LED 60 TriStrip™
©Elation Professional, Los Angeles Ca. 5 www.ElationLighting.com
2. SAFETY INSTRUCTIONS
To guarantee proper and consistent operation, it is important to
follow the guidelines in this manual. Elation Professional will not
accept responsibility for damages resulting from the misuse of
this fixture due to the disregard of the information printed in this
manual.
1. Always be sure that the fan and the air inlets remain clean and are never
blocked. Allow about 6” (15cm) between this fixture and other devices or a wall
to allow for proper cooling.
2. Never touch the fixture during normal operation.
3. Never look directly into the lamp beam. You risk injury to your retina, which may
induce blindness.
4. For safe operation, follow the Installation guide described in chapter two of this
manual. Operating the Design LED 60 TriStrip™ without suited safety aids such
as safety cables or clamps can increase the risk of damage and/or personal
injury.
5. Installation should only be performed by qualified and certified personal.
6. When mounting this fixture, use only the original rigging points included with this
fixture. Any structural modification will void the original manufactures warranty
and may increase the risk of damage and/or personal injury.
7. To reduce the risk of fire or shock, do not expose this fixture to rain or moisture.
8. Do not attempt to operate this fixture if the power cord has become damaged or
frayed.
9. Never open this fixture while in use.
10. This device falls under protection-class I. Therefore it is essential that the device
be grounded properly.
11. Qualified personnel must perform all electrical connections.
12. Be sure the available voltage matches the voltage requirements of the unit. Be
Design LED 60 TriStrip™
©Elation Professional, Los Angeles Ca. 6 www.ElationLighting.com
sure the power cord is never crimped or damaged. If the power cord is damaged,
replace it immediately with a new one of similar power rating.
13. Always disconnect from main power before performing any type of service or
any cleaning procedure.
14. Only handle the power cord by the plug. Never pull out the plug by tugging the
wire portion of the cord.
15. Please be aware that damages caused by modifications to the device are
not subject to warranty.
Important Notice: Damages resulting from the disregard of safety and general user
instructions found in this user manual are not subject to any warranty claims.
Design LED 60 TriStrip™
©Elation Professional, Los Angeles Ca. 7 www.ElationLighting.com
3. FEATURES
• Tri-Color LED Technology
• 62˚ Standard Beam Angle (48˚ Optional with 30˚ Lens Kit)
• Removable front cover to allow interchangeable Lenses
• Low power consumption
• Electronic menu display
• Minimal heat emission
• Maintenance free operation
• Equipped with 60 Three-Watt Tri-Color LEDs
• 100,000 hours rated LED life
• Linear RGB Color Mixing, 65 million color possibilities
• USITT DMX-512 complaint
• 5-pin and 3-pin Male and Female XLR Data Connectors
• Preprogrammed colored macros
• Strobe-effect with a maximum flash rate of 25fps
• DMX-controlled operation or stand-alone operation with Master/Slave-function
• 8 built-in programs accessed via DMX-controller or manually
• Sound-controlled via built-in microphone
• Individual control over each LED
• 0%~100% Dimming (two dimming options; linear & standard)
• Electronic power supply (100v~240V 50/60Hz)
• Six DMX Modes:
63 DMX-channels
60 DMX-channels
15 DMX-channels
6 DMX-channels
4 DMX-channels
3 DMX-channels
• Flicker-free operation for television and film
• Compact design: fits in 12” box truss
• Brilliant light output
• Linkable power supply (in and out power connectors) - Up to 8 units
Design LED 60 TriStrip™
©Elation Professional, Los Angeles Ca. 8 www.ElationLighting.com
4. GENERAL GUIDELINES
This fixture is a professional lighting effect designed for use on stage, in nightclubs, in
theatres, and other types of architectural installations. Do not attempt operation or
installation without a proper knowledge on how to do so.
This fixture was designed for indoor use only; use of this fixture outside will void the
manufacture’s warranty.
Consistent operational breaks will ensure that the fixture will function properly for many
years to come.
Do not shake the fixture around. Avoid brute force when installing or operating the fixture.
While choosing an installation location, please be sure that the fixture will not be exposed to
extreme heat, moisture, or dust. The minimum distance between the fixture and a wall or flat
surface should be at least .5 meter (about 1.5ft).
Always install the fixture with an appropriately rated safety cable. When installing the fixture
in a suspended environment always be sure to use mounting hardware no less than M10 x
25 mm, also be sure the hardware is only inserted in the yoke’s mounting holes.
Do not attempt to operate this fixture until you have familiarized yourself with all of its
functions.
Do not permit operation by persons not qualified for operating this type of theatrical fixture.
Most damages are the result of improper operation.
Please use the original packaging to transport the fixture in for service.
For your own safety, please read this user manual carefully before installing the device.
Design LED 60 TriStrip™
©Elation Professional, Los Angeles Ca. 9 www.ElationLighting.com
5. FIXTURE OVERVIEW
1. Bracket Locking Knob – This knob is used to secure the bracket in place after angle
adjustments have been made.
2. Fixture Chassis – Extruded aluminum slotted chassis, allows similar units to be
mounted together. See assembly instructions on page
3. Diffusing Lens/LED Assembly – This lens is used to both protect the LEDs as well as
diffuse the light output. Tri-Color LED assembly
4. Eye Bolt – This bolt is used a securing point for a safety cable.
5. On/Off Power Switch – Controls main power to the unit.
6. Power Input/Fuse Holder Assembly – This assembly holds the safety fuse as well as
provides a female IEC connector for a power cord. Always replace the fuse with an exact
match unless otherwise specified by an authorized Elation Service Technician. Using a
fuse other than that specified could seriously damage the unit and will void your
manufactures warranty.
Design LED 60 TriStrip™
©Elation Professional, Los Angeles Ca. 10 www.ElationLighting.com
7. Power Output Jack – Use this jack to jump power to another Design LED 60 TriStrip™
8. 3-Pin DMX Output Jack – This jack is used to send an incoming DMX signal to the next
fixture in the DMX chain via a female, 3-pin XLR jack.
9. 3-PIN DMX Input Jack – This jack accepts an incoming DMX signal via a male, 3-pin
XLR jack.
10. LED Menu Display - 4-segment menu display. Used to display the DMX address as
well as all other menu functions.
11. 5-PIN DMX Input Jack – This jack accepts an incoming DMX signal via a male, 5-pin
XLR jack.
12. 5-Pin DMX Output Jack – This jack is used to send an incoming DMX signal to the next
fixture in the DMX chain via a female, 5-pin XLR jack.
13. MENU Button - This button is used to access the fixtures menu functions.
14. Up Button – The up button is used to toggle forward through the menu functions and
settings.
15. Down Button – The down button is used to toggle backwards through the menu
functions and settings.
16. Enter Button – The enter button is used to enter in to a certain menu function or to lock
a menu setting in to memory.
17. Cooling Fans – These fans regulate the internal operating temperature of the fixture. To
prevent overheating or failure be sure to never block or obstruct these fans in any way.
Design LED 60 TriStrip™
©Elation Professional, Los Angeles Ca. 11 www.ElationLighting.com
6. MOUNTING AND INSTALLATION
Yoke Assembly – Single Unit Operation (DLED 12 Brick shown for illustration purposes only).
The device can be placed directly on the stage floor or rigged in any orientation on a truss
without altering its operation characteristics. When connecting the hanging yoke to the
fixture, refer to the illustration below.
Cautions:
For added protection mount the fixtures in areas outside walking paths, seating areas, and
away from areas were the fixture might be reached by unauthorized personal.
Before mounting the fixture to any surface, make sure that the installation area can hold a
minimum point load of 10 times the device’s weight.
Fixture installation must always be secured with a secondary safety attachment, such as an
appropriate safety cable.
To avoid injury, never stand directly below the device when mounting, removing, or servicing
the fixture.
Refer to regulations BGV C1 (formerly VBG 70) and DIN VDE0711-217
for proper installation in Europe To ensure proper installation, only
qualified staff should attempt installation.
Mounting points
Overhead mounting requires extensive experience, including amongst others calculating
Design LED 60 TriStrip™
©Elation Professional, Los Angeles Ca. 12 www.ElationLighting.com
working load limits, a fine knowledge of the installation material being used, and periodic
safety inspection of all installation material and the fixture. If you lack these qualifications, do
not attempt the installation yourself. Improper installation can result in bodily injury.
Be sure to complete all rigging and installation procedures before connecting the main
power cord to the appropriate wall outlet.
Mounting
The Design LED 60 TriStrip™ is fully operational in any mounting position, hanging
upside-down from a ceiling, side mounted, or set on a flat level surface. Be sure this fixture is
kept at least 0.5m away from any flammable materials (decoration etc.). When clamp
mounting; always use and install the supplied safety cable as an added safety measure to
prevent accidental damage in the event of a clamp failure. See the image below.
Design LED 60 TriStrip™
©Elation Professional, Los Angeles Ca. 13 www.ElationLighting.com
CAUTION!
Be sure a qualified electrician performs all electrical
connections before attempting any operation.
Clamp Mounting
The Design LED 60 TriStrip™ provides a unique mounting bracket assembly that allows the
unit to stand on flat surface, hang on truss via a clamp, or be used in cluster allow multiple
units to rigged together (see the illustration below). Regardless of the mounting option you
choose please refer to the safety guidelines in this manual to avoid damage to the unit
and/or injury to persons.
When mounting this fixture to truss be sure to secure an appropriately rated clamp to the
hanging yoke using a M10 screw fitted through the center hole of the hanging yoke. As an
added safety measure be sure to attach at least one properly rated safety cable to the fixture.
See illustration below.
Securing the Design LED 60 TriStrip™
Always secure your fixture with a safety cable when
suspending the unit from truss or other means. The fixture
provides a built-in rigging point for a safety cable as illustrated
above. Be sure to only use the designated rigging point for a
safety cable. Never secure a safety cable to the hanging
bracket.
Loading...