Elation 5R SNIPER User Manual
5R SNIPER STAGE LIGHT
USER MANUAL
KEEP THIS MANUAL FOR FUTURE NEEDS
2
Thank you for your patronage. We are confident that our excellent products and service can
satisfy you. For your own safety, please read this user manual carefully before installing the
device.
In order to install, operate, and maintain the lighting safety correctly. We suggest that the
installation and operation should be done by the verified technician and follow the instruction
strictly.
A CAUTION!
Keep this device away from rain and moisture!
CAUTION!
Unplug mains lead before opening the housing.
Every person involved with the installation, operation and maintenance of this device has to:
-be qualified
-follow carefully the instructions of this manual
INTRODUCTION:
Thank you for having chosen this professional moving head.
You will see you have acquired a powerful and versatile device.
Unpack the device. Inside the carton box you should find:
1. One power cable
2. One user manual
（
Flight case, Safety cable and Clamps are optional, please contact your dealer
）
Please check carefully that there is no damage caused by transportation. Should there be any,
please consult your dealer and don’t install this device.
SAFETY INSTRUCTIONS
CAUTION!
Be careful with your operations. With a dangerous voltage you can suffer a
dangerous electric shock when touching wires!
This device has left the factory in perfect condition. In order to maintain this condition and to
ensure a safe operation, it is absolutely necessary for the user to follow the safety instructions
and warning notes written in this user manual.
1. In order to guarantee the product’s life, please don’t put it in the damp places or even the
environment over 60degress.
2. Always mount this unit in safe and stable matter.
The qualified professionals are allowed to carry out the lamp installation, operation and
maintenance, but they must guarantee to operate in strict accordance with the instructions
referred to.
3
3. Using lamp, the change rate of power voltage should be within±10%, if the voltage is too
high, it will shorten the light’s life; if it’s not enough, the lamp will be dark.
4. Please restart it after turning off light for 20 minutes until full-cooling. Frequent switching
will reduce the life span of lamps and bulbs; intermittent using will improve the life of bulbs
and lamps.
▲ Important:
Damages caused by the disregard of this user manual are not subject to
warranty. The dealer will not accept liability for any resulting defects or
problems.
If the device has been exposed to temperature changes due to environmental changes, do not
switch it on immediately. The arising condensation could damage the device. Leave the
device switched off until it has reached room temperatures.
This device falls under protection-classⅠ. Therefore it is essential that the device be earthed.
The electric connection must carry out by qualified person.
Make sure that the available voltage is not higher than stated at the end of this manual.
Make sure the power cord is never crimped or damaged by sharp edges. If this would be the
case, replacement of the cable must be done by an authorized dealer.
Always disconnect from the mains, when the device is not in use or before cleaning it. Only
handle the power cord by the plug. Never pull out the plug by tugging the power cord.
During initial start-up some smoke or smell may arise. This is a normal process and does not
necessarily mean that the device is defective, it should decrease gradually.
Please don’t project the beam onto combustible substances.
If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively
replaced by the manufacturer or his service agent or a similar qualified person in order to
avoid a hazard.
CAUTION!
Never touch the device during operation!
The housing may heat up!
C CAUTION!
N Never look directly into the light source,
A As sensitive persons may suffer an epileptic shock.
CLEANING AND MAINTENANCE
1. To reduce the risk of electrical shock or fire, do not expose this unit to rain or moisture.
2. Do not spill water or other liquids into or on to your unit.
3. During long periods of non-use, disconnect the unit’s main power.
4
4. It should be installed in a well-ventilated place, at a distance of 50 centimeters or more
with the walls. At the same time, please check if the fan and ventilation holes are
unobstructed.
The following points have to be considered during the inspection
1) All screws for installing the devices or parts of the device have to be tightly connected
and must not be corroded.
2) There must not be any deformations on the housing, color lenses. Fixations and
installations spots(ceiling, suspension, trussing).
3) Mechanically moved parts must not show any traces of wearing and must not rotate with
unbalances.
4) The electric power supply cables must not show any damage, material fatigue or
sediments. Further instructions depending on the installation spot and usage have to be
adhered by a skilled installer and any safety problems have to be removed.
CAUTION!
Disconnect from mains before starting maintenance operation!
In order to make the lights in good condition and extend the life time, we suggest a regular
cleaning to the lights.
1) Clean the inside and outside lens each week to avoid the weakness of the lights due to
accumulation of dust.
2) Clean the fan each week.
3) To make sure the smooth gobo rotation, we suggest adding proper lube to the wheel each
three month, avoiding the excessive lube splashes during the gobo rotating,
4) A detailed electric check by approved electrical engineer each three month, make sure
that the circuit contacts are in good condition, prevent the poor contact of circuit from
overheating.
We recommend a frequent cleaning of the device. Please use a moist, lint-free cloth. Never
use alcohol or solvents.
There are no serviceable parts inside the device except for the lamp. Please refer to the
instructions under “Installation instructions”.
Should you need any spare parts, please order genuine parts from your local dealer.
TECHNICAL PARAMETERS
POWER SUPPLIE
Input power:110-240V 50/60 Hz
Loading...