ELANT EL4331CS Datasheet
EL4331C
Triple 2:1 Mux-Amp AV = 1
EL4331C
Features
•3 ns A-B switching
• 300 MHz bandwidth
• Power down mode
• TTL/CMOS compatible controls
• Fixed gain of 1
• 400V/µs slew rate
Applications
• RGB multiplexing
• Picture-in-picture
•Cable driving
• HDTV processing
• Switched gain amplifiers
• ADC input multiplexer
Ordering Information
Part No. Temp. Range Package Outline#
EL4331CS -45°C to +85 °C 16-Lead SOIC MDP0027
General Description
The EL4331C is a trip le , ve ry hi gh sp eed , 2 :1 Mu ltip le x ing Am pl ifie r.
It is intended primarily for component vid eo multiple xing, and is es pecially suited for pixel switching. The amplifiers have their gain set to
1, internally. All three amplifiers are switched simultaneously from
their A to B inputs by the TTL/CMOS compatible, common A/B control pin.
The EL4331C has a power down mode, in which the total supply current drops to less than 1 mA. In this mode, each output will appear as
a high impedance.
The EL4331C runs fro m st an dard ±5V s uppl ie s, an d is a vai lable in the
narrow 16-pin small outline package.
© 1995 Elantec, Inc.
Connection Diagrams
October 6, 1999
EL4331C
Triple 2:1 Mux-Amp AV = 1
EL4331C
Absolute Maximum Ratings (T
VCC to V
EE
to Any GND 12V
V
CC
to Any GND 12V
V
EE
Continuous Output Current 45 mA
Any Input (except P
Input VCC-7V to VCC+0.3V
P
D
)V
D
= 25 °C)
A
-0.3V to VCC+0.3V
EE
14V
Input Current, Any Input 5 mA
Power Dissipation See curves
Operating Temperature -45°C to +85°C
Leading Temperature during Soldering 300°C
Junction Temperature 170°C
Storage Temperature -60°C to +150°C
Important Note:
All parameters having Min/Max specifications are guaranteed. The Test Level column indicates the specific device testing actually performed during
production and Quality inspection. Elantec performs most electrical tests using modern high-speed automatic test equipment, specifically the LTX77
Series system. Unless otherwise noted, all tests are pulsed tests, therefor T
= TC = TA.
J
Test Level Test Procedure
I 100% production tested and QA sample tested per QA test plan QCX0002.
II 100% production tested at T
= 25°C and QA sample tested at TA = 25°C, T
A
MAX
and T
per QA test plan QCX0002.
MIN
III QA sample tested per QA test plan QCX0002.
IV Parameter is guaranteed (but not tested) by Design and Characterization Data.
V Parameter is typical value at T
= 25°C for information purposes only.
A
DC Electrical Characteristics
VCC = +5V, VEE = -5V, Ambient Temperature =25°C, RL = 500Ω, PD = 5V
Parameter Description Min Typ Max
V
OS
dV
OS
I
B
dI
B
AV
OL
Input Referred Offset Voltage -12 30 II mV
Input A to Input B Offset Voltage
[1]
18II mV
Input Bias Current -7 -30 II µA
Input A to Input B Bias Current
[1]
0.5 4.0 II µA
Open Loop Gain (from Gain Error Calculation) 54 VdB
PSRR Power Supply Rejection Ratio 60 70
_500 Output Voltage Swing into 500Ω Load ±2.7 ±3.2 II V
V
OUT
V
_150 Output Voltage Swing into 150Ω Load +3/-2.7 VV
OUT
I
OUT
X
TALK
V
IH
V
IL
I
IL_AB
I
IH_AB
I
IL_PD
I
IH_PD
I
S
I
S(PD)
Current Output, Measured with 75Ω load Crosstalk from Non-Selected Input (at DC) -70 -85 II dB Input Logic High Level (A/B and PD) 2.0 II V Input Logic Low Level (A/B and PD) 0.8 II V Logic Low Input Current (VIN = 0.8V), A/B Pin -1 -20 -100 II µA Logic High Input Current (VIN = 2.0V), A/B Pin -5 0 5 II µA Logic Low Input Current (VIN = 0.8V), PD Pin -10 0 10 II µA Logic High Input Current (VIN = 5.0V), PD Pin 0.5 1.0 1.6 II mA Total Supply Current 38 48 60 II mA Powered Down Supply Current 0.01 1.0 II mA
[2]
30 40 II mA
1. Any channel’s A-input to its B-input.
2. There is no short circuit protection on any output.
Test Level Units
II dB
2
EL4331C
Triple 2:1 Mux-Amp AV = 1
AC Electrical Characteristics
VCC = +5V, VEE = -0.5V, Ambient Temperature = 25°C, RL = 150Ω and CL = 5 pF
Parameter Description Min Typ Max Test Level Units
BW -3 dB Bandwidth
SR Slew Rate (4V Square Wav e, Measured 25%–75%) 400 V V/µs T
S
T
AB
OS Overshoot, V
-10M Input to Input Isolation at 10 MHz 53 V dB
I
SO-AB
I
-100M Input to Input Isolation at 100 MHz 33 V dB
SO-AB
I
-10M Channel to Channel Isolation at 10 MHz 56 V dB
SO-CH
I
SO-CH-CH
Pkg Peaking with Nominal Load 0 V dB
T
ON_PD
T
OFF_PD
-3 dB BW with 250Ω and 10 pF Load
Settling Time to 0.1% of Final Value 13 V ns
Time to Switch Inputs 3 V ns
= 4V
OUT
pk-pk
-100M Channel to Channel Isolation at 100 MHz 33 V dB
Power Down Turn-On T ime 150 V ns
Power Down Turn-Off Time 1 V µs
300
400
8V%
V
V
EL4331C
MHz
MHz
3
EL4331C
Triple 2:1 Mux-Amp AV = 1
EL4331C
Typical Performance Curves
3 dB Bandwidth Small Signal Transmit Response Large Signal Transient Response
Switching from Ground to An
Uncorrelated Sine Wave and Back
Switching Glitch, 0V to 0V with 2 ns AB edges Switching Glitch, 0V to 0V with 10 ns AB Edges
Switching a Family of DC Levels to Ground and Back
4
Loading...