Elan TP7 Quick Install Manual

Job: Universal Manual

Size: 150 x 150 mm folded

02/17/2015 -> Final print pdf

ELAN & Niles & SpeakerCraft

Quick Install Guide – TP7

8 pages each - Format: 150 x 300 mm ( Metric !! )

Final Print pdf / Rev E

English only

02/17/2015 - TU

Questions?
Juergen 707 - 778 - 5826

P/N 9901341 REV. E0 02/2015

+

Folding-Method:

Folded size:

150 x 150 mm

Open:

600 mm wide x 300 mm high

No bleed

150 150 150 150

300

TP7 – 7” Touch Panel

User Interface

Quick Install Guide

English

TP7 – 7” Touch Panel

User Interface

Quick Install Guide

English

9901341_Rev-E0_Universal_TP7_QSG_0217_PRINT.indd 1-4 2/17/15 1:54 PM

Thank you for including the TP7 as part of the user interface
strategy for your customer. The TP7 has been designed to
provide years of trouble free operation when wired and installed
properly. The TP7 has been designed for installation in low
humidity indoor environments and should never be installed
outdoors or in high humidity areas.

Included in the box

• 1ea TP7 touch panel

• 1ea TP7 mounting bracket

• 4ea Mounting screws

• 1ea DC power connector

Introduction

To install the TP7 you will also need a standard 2 gang
US junction box or low voltage bracket.

FCC and IC Information:

This Class B digital apparatus complies with Part 15 of the FCC rules and with Canadian ICES-003 and RSS-210.

Operation is subject to the following two conditions:

1. This device may not cause interference and

2. This device must accept any interference, including interference that may cause undesired operation of the device.

Cet appareil numérique de classe B est conforme aux normes canadiennes ICES-003 et RSS-210. Son fonctionnement
est soumis aux deux conditions suivantes : (1) cet appareil ne doit pas causer d’interférence et (2) cet appareil doit
accepter toute interférence, notamment les interférences qui peuvent affecter son fonctionnement.

Warning: Changes or modifi cations to this unit not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.

FCC and IC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets
the exemption from the routine evaluation limits in section 2.5 of RSS 102.

1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with a minimum distance of 20 centimeters from user and bystanders.

Informations concernant l’exposition aux fréquences radio (RF):

La puissance de sortie émise par l’appareil de sans fi l est inférieure à la limite `exposition aux fréquences radio d’Industry
Canada (IC). Utilisez l’appareil de sans fi l de façon à minimiser les contacts humains lors du fonctionnement normal.
Ce périphérique a également été évalué et démontré conforme aux limites d’exposition aux RF d’IC dans des conditions
d’exposition à des appareils mobiles (antennes sont supérieures à 20 cm à partir du corps d’une personne).

Warning: The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102,
and users can obtain Canadian information on RF exposure and compliance from the Canadian Representative
Product Solutions Group at Tel: [phone].

Important Safety Instructions

1. Read, understand and follow ALL safety and installation instructions included in this manual.
Failure to follow the included documentation may damage the product and will void manufacturer’s warranty.

2. Follow ALL installation guidelines included with the product. Installation of the product in high humidity environments,
in close proximity to heat sources and /or non-recommended locations WILL impede, interfere and/or damage
the intended operation of the product

3. Only use attachments and accessories which have been specifi ed for use by the manufacturer.

4. The use of abrasive, liquid or solvent based cleaning fl uids WILL damage the product.
Please refer and follow all Product Care instructions included with the product.

5. Product Servicing may ONLY be completed by authorized or certifi ed service centers & personnel.
For a complete list of product servicing options, please follow instructions included in the product
documentation and /or contact original manufacturer for details.

FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/ TV technician for help.

Specifi cations

Dimensions Overall 8”w x 5”h

Mounting Depth 1 ¾”

Microphone Dual Digital Beam Forming
Far Field Pickup

Speaker 2w integrated

Camera 640 x 480

Display 7”

800 x 480

Network 10/100 Ethernet

802.11 B/G/N WiFi

Connections

LAN/PoE RJ- 45
Power 2 pin Phoenix
USB USB Type A
Audio Out 1/8” stereo (Future Use)

Power Requirements

Direct – 12V 1 A
PoE – IEEE 802.3at,
13w maximum draw
(@48 V 270 mA max)

TP7 – 7” Touch Panel

User Interface

Quick Install Guide

English

© 2014 Core Brands, LLC. All rights reserved.
Core Brands,LLC,aNortek company.

P/N 9901341 Rev. E0 02/2015

42

Powering up the TP7

The TP7 will automatically power on when power is applied. Wait for the unit to boot up.

- If connected to a wired Ethernet switch the TP7 will aquire a network address
via DHCP and automatically connect to the system.

- If the TP7 does not detect a wired Ethernet connection and the WiFi radio has never been confi gured
you will be presented with the Network Confi guration Utility interface. To complete the network
confi guration please refer to the most current training documentation for your system.

Setting screen orientation

The TP7 is shipped pre-confi gured for landscape orientation.

To change orientation:

– Press and hold power button for 3 seconds.
– Select Confi gure Panel from the popup menu.
– Select landscape or portrait orientation.

Removing the TP7

– Using two hands grasp it on each side or the top and bottom and pull straight
out from the wall. It will require approx. 10lbs of force to remove it from the bracket.

RESET

The recessed RESET button has two functions.

– Tap the button to reset the network confi guration.
– Press and hold the button for 10 seconds to restore the TP7 to factory default confi guration.

CAUTION:

Neither of these actions can be reversed.

53

Recessed
Reset Switch

LAN + Power
over Ethernet

Recessed
Reset Switch

Power

Paper Clip

Mounting Bracket

TP7 Frame

Top of 2 Gang Box

Dry Wall

Mounting Bracket

9901341_Rev-E0_Universal_TP7_QSG_0217_PRINT.indd 5-8 2/17/15 1:54 PM